Popular Post Gixxerjoe04 Posted July 14, 2017 Popular Post Report Posted July 14, 2017 Been working on these end tables for my wife for the past few weeks and finally got them finished, well enough for her liking. Used my track saw to cut the miters, there was a ton of tension in the wood, was a pain in the asprin. My ts75 bogged down and didn't want to cut through, made 3 cuts at 20mm each and it was still too much for my tracksaw. After that pain, used my domino on the joints to strengthen them. Finished them with arm-r-seal, of course something went wrong with my last coat, not sure what but I want to strip them and do it again but the wife said no she thought they were fine. Glued on waste blocks near the miters to clamp the joint down, the glue stained the wood or something, sanded and card scraped the hell out of it but you can still tell if you look hard enough. Needless to say, I cussed a lot during this build haha, but the wife is happy so it's all good. I like how they came out overall but wanted them a little longer but didn't have a longer slab to work with. I had better pics from my good camera but didn't feel like waiting to upload and resize them. 11 Quote
shaneymack Posted July 14, 2017 Report Posted July 14, 2017 Nice job, Joe, they turned out great. Did you make your crosscut first and then cut your miter? Sent from my SM-N910W8 using Tapatalk Quote
Brendon_t Posted July 14, 2017 Report Posted July 14, 2017 That looks great Joe. I'm also interested in what was causing the saw to bog down. The only time I've seen that is when the stock wasn't flat before starting the cut. Quote
gee-dub Posted July 14, 2017 Report Posted July 14, 2017 Beautiful material, nice tight miters and clean butterfly Dutchman . . . simple, clean lines and a custom fit for their role . . . what's not to like? Are the dark markings on the edges of the sapwood where the bark was removed? I really like the satiny finish. Quote
Gixxerjoe04 Posted July 14, 2017 Author Report Posted July 14, 2017 13 minutes ago, shaneymack said: Nice job, Joe, they turned out great. Did you make your crosscut first and then cut your miter? Sent from my SM-N910W8 using Tapatalk No, the first cuts both ways were too rough so had to clean them up after the initial cut but as you can see, making a cross cut first wouldn't have mattered. Thought about sending in my ts because it sounded so underpowered, it's only 1.5" walnut. 8 minutes ago, Brendon_t said: That looks great Joe. I'm also interested in what was causing the saw to bog down. The only time I've seen that is when the stock wasn't flat before starting the cut. Was pinching the blade. Quote
Gixxerjoe04 Posted July 14, 2017 Author Report Posted July 14, 2017 2 minutes ago, gee-dub said: Beautiful material, nice tight miters and clean butterfly Dutchman . . . simple, clean lines and a custom fit for their role . . . what's not to like? Are the dark markings on the edges of the sapwood where the bark was removed? I really like the satiny finish. Yea it's from the bark, I was gonna sand it all off but it didn't want to come off, so I left it. Not a fan of semi gloss or gloss, I satin everything except stuff I turn. Quote
shaneymack Posted July 14, 2017 Report Posted July 14, 2017 i would check the toe in adjustment on your saw. At full plunge you should have .002" from the front teeth to the back. Quote
pkinneb Posted July 14, 2017 Report Posted July 14, 2017 Those turned out great! Like the design as well. Quote
Gixxerjoe04 Posted July 14, 2017 Author Report Posted July 14, 2017 4 minutes ago, shaneymack said: i would check the toe in adjustment on your saw. At full plunge you should have .002" from the front teeth to the back. Did that and it was fine, I didn't like how much side to side play there is but saw nothing in the manual on how to adjust or tighten it. Quote
wtnhighlander Posted July 14, 2017 Report Posted July 14, 2017 Nice work, Joe! I love how clean the miter cuts came out. The grain alignment looks perfect! Quote
Pondhockey Posted July 14, 2017 Report Posted July 14, 2017 Very nice. The butterflied boards make it look like you used the full width of the tree, with matching sapwood ends. Nice effect. Quote
Gixxerjoe04 Posted July 14, 2017 Author Report Posted July 14, 2017 8 minutes ago, Pondhockey said: Very nice. The butterflied boards make it look like you used the full width of the tree, with matching sapwood ends. Nice effect. It's a solid 17" wide slab, the butterflies were for the cracks. Both tables came from an 8.5' slab, wish is would have been a foot longer. Quote
wdwerker Posted July 14, 2017 Report Posted July 14, 2017 Clean the blade first ! Nice tables ! Quote
Eric. Posted July 14, 2017 Report Posted July 14, 2017 I get bitching, moaning, whining, complaining...and burning...from my track saw too. I even sent mine to Festool for them to re-calibrate and it came back exactly the same way. Same story with the Kapex. New blade, flat stock, doesn't matter. It's a wuss. I try to only use it for sheet goods like it was intended, but if I do use it on thick hardwood I'll always make a skim cut after the initial cut because the first one is never that great. The 75 should have more balls than the 55 but it still doesn't surprise me. Quote
Popular Post Gixxerjoe04 Posted July 15, 2017 Author Popular Post Report Posted July 15, 2017 I was hoping the way I situated them my son wouldn't be able to climb on them since he's not walking yet but I was wrong. They're a lot more stable than the last tables at least. 3 Quote
Chet Posted July 15, 2017 Report Posted July 15, 2017 Those are some great looking tables and they appear to be the perfect hight for the little guy. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.