Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

QSWO Media Cabinet

Featured Replies

  • Popular Post

I started this Media Cabinet a while back and thought I would do a journal.  I am finally getting around to posting here.  This project is almost complete, I start the ARS top coats tomorrow.  I know a lot is done here with SketchUp but I still use an older program called iDraw using A pencil and paper.  I am using Quarter Sawn White Oak and was going for some what of an Arts and Craft look, only mine is pretty simple and gets the Arts and Craft look more from the couple of pieces of hardware and the finish that I chose.  There were some things I haven't done before like doing a draw bore mortise and tenon.  This came about because I presently don't have 60 inch clamps and didn't feel like buying any at this time.  So I did the draw bore to attach the top and bottom rails to the legs, front and back.  Another first, I used a four step stain and finish process to get the color I wanted with the white oak.  Normally I let the natural color of the wood do the talking.

I will warn you ahead of time, there are some missing parts to this journal.  I get to working and in a zone of sorts and forget to take pictures but i am pretty sure we have seen milling and glue ups.

Here is a simple drawing that I worked from.  The only absolute measurements were those of the center section because of some electrical components the will be housed there.  Everything else is built off of that.

Scan.jpeg

First thing I did was layout everything, for the most part, for rough cuts.

IMG_5673.jpg

Then the first thing I glued up was the blanks for the legs.  I would have prefer to make these out of 8/4 material but my local place doesn't care quarter sawn white oak in 8/4 For some reason.

IMG_5675.jpg

I got distracted and forgot to go back and clean up the squeeze out when it skinned over so I cleaned it up with a beater block plan.

IMG_5678.jpg

While the legs were in the clamps I started on the top and bottom rails.  I was having some problems with my jointer and didn't feel like fiddling with it at the moment so I preped the rails with my low angle jack.

IMG_5679.jpg

Then I laid out the mortises in the legs.  Can't believe how ugly this wood looks in these pictures.

IMG_5682.jpg

I rigged up a couple of start and stop blocks and used my router with two edge guides to cut the mortises.

IMG_5688.jpg

Then squared them up with the chisels. 

IMG_5691.jpg

Stay tuned...

 

 

  • Replies 79
  • Views 19.8k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • As I mentioned before the finish process I used, I got from a guy named Jeff Jewitt.   It was a four step process.  I had two colors that I was interested in and fortunately only one item, the dye sta

  • So the doors are a simple frame and panel design with a little twist.  I made some cutouts in the panels. This was something that was done by a furniture maker named Charles Limbert during the Arts &a

  • I laided out the angle for the bottom of the legs. I stood them up in their orientation to double check their placement. Cut them at the band saw to the strong side of the line.

Posted Images

Looks awesome Chet!  Knowing where that's going to live in your house, that should fit in awesome!

Now I'm considering 2 edge guides for my little Dewalt plunge router, thanks for helping me spend more . Guess I had it coming, I'm sure I've done it plenty of times myself.

Nice looking project . I'll be following along.

  • Author
35 minutes ago, wdwerker said:

Now I'm considering 2 edge guides for my little Dewalt plunge router, thanks for helping me spend more

well if you want to go to the heart of the problem, I got the idea from Kev.  It works out great.

6 minutes ago, Chet said:

well if you want to go to the heart of the problem, I got the idea from Kev.  It works out great.

We used that when we cut the mortise for the leg vise on Chet's bench.  I can't take the credit but, I don't recall where I saw it.

Looking forward to watching this! A carbide paint scraper is great for removing glue. 

  • Author
  • Popular Post

I forgot to post this the other day.  This was after all the mortises were all cleaned up.  My five year grand daughter came out will I was doing this, spotted the mallet, thought it was cool looking and decided she needed to help me hit the chisel.  So I lined up the chisel, she took careful aim and hit my hand.   But after a couple of trys she got the hang of it and actually did pretty good.

IMG_5704.jpg

 

First thing I did when I got back to it was glue up the side panels so they would be ready when it came time to attach the legs.

I used some biscuits for alinement.

IMG_5697.jpg

Then into the clamps.

IMG_5701.jpg

I did some needed layout on the top and bottom rails.  Hard to see in the photo.

IMG_5680.jpg

Then I cut the tenons on the table saw and adjusted the fit with the plane.  This was the first photo fail, no pictures but here is one of the first dry fit.

IMG_5703.jpg

Thats it.  It was a short day.

 

 

 

7 minutes ago, Chet said:

she took careful aim and hit my hand.

:lol:

When my kids want to "help" me in the shop...I've got two words for ya: sandpaper - scraps

That is all.

  • Author
1 hour ago, Eric. said:

:lol:

When my kids want to "help" me in the shop...I've got two words for ya: sandpaper - scraps

That is all.

She is only five but she is to smart for that.  She wants to be were the fun is.  She is pretty tenacious at working through a problem or skill.

  • Author
  • Popular Post

I laided out the angle for the bottom of the legs.

IMG_5707.jpg

I stood them up in their orientation to double check their placement.

IMG_5708.jpg

Cut them at the band saw to the strong side of the line.

IMG_5709.jpg

And then cleaned them up back to the line with my smoother.

IMG_5710.jpg

And finally sanded them on all for sides before gluing up the legs and side panel.

IMG_5711.jpg

Along with these two side and leg glue ups, I also had the the bottom and two center dividers in the clamps.

IMG_5712.jpg

Then I made up these two pieces... what ever they're called.  The tongue that is facing down to the bench will go in dados on the top and bottom back side rails.  The 3/4 inch groove down the center will hold the two center panels that will create the center section of the cabinet and the 90 angle at the top left of the left piece and top right of the right piece when in place will create the groove for the back panels on the left and right sections.

IMG_5714.jpg

Stay tuned for more.

I'm in on this one to. Looking to see how much you can make Steve spend.

CHET!! Why is your drawing the cleanest and most beautiful handwriting ever? So precise too! All my sketches look like a 4 year old did it and my builds all look like an 8 year old built them. :( 

In one of your first pics, I noticed 4 squares on your bench next to some qswo. And I wondered why.  Now I know, you needed one square for each leg.   Makes perfect sense to me.  

30 minutes ago, Chet said:

I took two years of drafting in high school, again all pencil and paper, about 20+ years before CAD was even thought about.

Me too, except I did half and half. I won state with an autocad drawing and a pencil/paper drawing .... mine are still sloppy though when I do it myself haha.

Maybe one day I will slow down and make pretty drawings and more accurate to scale drawings.

  • Author
50 minutes ago, RichardA said:

In one of your first pics, I noticed 4 squares on your bench next to some qswo. And I wondered why.  Now I know, you needed one square for each leg.   Makes perfect sense to me.  

Each square had a different part or the measurements for the layout of the mortises at the top and bottom of the legs.  I like to leave them set up until the mortises are finished just in case I mess up and have to layout a back up part. 

  • Author
  • Popular Post

I spent one day doing nothing but milling, gluing up and putting a final size to panels.  One bottom panel, 2 center section dividers, 3 back panels, 2 selves and the top, which I wish I hadn't done because it kept getting in the way.  

The next thing I did was take the two door stiles that would get hinge mortises and the two legs to match.  

I put down some blue tape and traced the hinge onto that with my marking knife and then removed the tape were the hinge would go.  I did this with the blue tape to create a better contrast for me to remove most of the waste with my router,  easier for me to see the tape border then a pencil or knife line.

IMG_5751.jpg

Hogged out most of the waste.

IMG_5735.jpg

And finished up with the chisel.

IMG_5738.jpg

I am happy with that.

IMG_5739.jpg

And finally I stated the assembly.  First the top and bottom rails, front and back.  Again I was using a draw bore mortise and tenon joint here and because the day was a little warm and I didn't know how it was going to go for the first time down this road, I used some Titebond III to give me a little time to work.  But as it turned out all things went pretty well.   One peg snapped just as it came through on the back side but no big problems.

IMG_5750.jpg

Then I put in the bottom, the two center section panels and gave the back panels a test fit.

IMG_5754.jpg

IMG_5757.jpg

And a view of the back.

IMG_5758.jpg

There will be more to come. :)

I like the blue tape Idea.  Your very good with a chisel.   Cabinet is looking good.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.