BillyJack Posted December 9, 2022 Author Report Share Posted December 9, 2022 I measured my 1000 chip poker case and it’s 2.25 and I have 4.25 in the center.. Did you hear that? I’m brainstorming.. Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 9, 2022 Author Report Share Posted December 9, 2022 I feel like the “God of Thunder” 2 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 11, 2022 Author Report Share Posted December 11, 2022 If I use storage all is fine and I need only build up for the playing surface. If I don’t build for storage I need to make the beauty ring, wrap the inside edges and drop down the playing surface which will be more of pit poker… 1 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 12, 2022 Author Report Share Posted December 12, 2022 I’m also considering pin lights around the playing surface. I’ve seen a lot of guys use Christmas lights. Something I’m considering.Maybe make the inne4 chip ring removable or make the inner ring removeable with wiring 1 Quote Link to comment Share on other sites More sharing options...
Mark J Posted December 13, 2022 Report Share Posted December 13, 2022 Would they be shaded from view? Personally I find looking into lights annoying, but that's hust me. Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 13, 2022 Author Report Share Posted December 13, 2022 I don’t think I’ve ever heard anyone complain about the view. Normally they will have an area behind a CNC strip that houses the lights. The aluminum or wood strip blocks the hardware, but allows light penetration. I think it’s low light. In my case I’ll make a 1/2 x2.5 band along the inside and drill tapered holes on the inside using a drill press and wrap with a another 1/8 Masonite with 1/8-1/4 holes and cover in walnut. Followed by clear plastic..Or paint it black. That’s the beauty of creating something new. My challenge is being cheap.lol Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 28, 2022 Author Report Share Posted December 28, 2022 Finally back to the build. I cut the masonite. I'll use the upholstery gun to hold it in place. 1 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 I’m going to have to make a roller for glue… Quote Link to comment Share on other sites More sharing options...
Coop Posted December 29, 2022 Report Share Posted December 29, 2022 What is an upholstery gun? Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 Wire staples. I believe they are 22guage. it won’t shot thru 1/8 Masonite. 1 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 I’ll need a minimum of 4 layers which will be 8 rips of 4 5/16. Normally I just kerf cut plywood for the radius. Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 Shops heating up. Hopefully I can get this banded today. Because the plywood is just slightly warped, so I’ll have to come up with a plan to keep it flat while I wrap it. Not sure I still have an old roller for wide glue ups. I’ll have to make something... Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 Stapler and staple used.. 1 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 First rap is done... 1 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 If you don't have patience, don't build table..lol 2 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 Hope to get this part done..Boring… Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 I’m really going have to dig in the wood pile tomorrow. If I don’t find more cherry for the outside radius , it’s going to be walnut..I couldn’t find any cherry veneer the other day. Plenty walnut and maple.. 2 Quote Link to comment Share on other sites More sharing options...
treeslayer Posted December 29, 2022 Report Share Posted December 29, 2022 And I thought I had a lot of clamps Looking great Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 29, 2022 Author Report Share Posted December 29, 2022 Looks good, but someone has to put them back up 2 Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 30, 2022 Author Report Share Posted December 30, 2022 All the layers are glue and dried. Total width of 49 5/8. Won't get much done today. Maybe the cup holder sides tomorrow. Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 30, 2022 Author Report Share Posted December 30, 2022 5" thick... 2 Quote Link to comment Share on other sites More sharing options...
Mark J Posted December 31, 2022 Report Share Posted December 31, 2022 Coming along. What do you figure the table is going to weigh when you're done? Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 31, 2022 Author Report Share Posted December 31, 2022 When I shipped the last one , I honestly don’t remember weight. I remember them charging for footage on the truck..We agreed to not ship the glass. it’s not actually that heavy, but because of its radius, it is bulky to move.. Quote Link to comment Share on other sites More sharing options...
BillyJack Posted December 31, 2022 Author Report Share Posted December 31, 2022 Eight now I'm trying tl decide on lights. 1 Quote Link to comment Share on other sites More sharing options...
Grabovetskiy Posted December 31, 2022 Report Share Posted December 31, 2022 Great job! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.