Popular Post gee-dub Posted October 25, 2024 Author Popular Post Report Posted October 25, 2024 I needed a helping hand to hold one end of these longer pieces during dry-fit and glue up so I cobbled these together. I normally final mill and hand tool parts right before glue up. Due to being sick I have let parts set longer than normal. Wood being what it is the parts moved and things don't align as well as they once did. I found tapering the ends of the tenons help me slip long and awkward parts together more easily. I hook some clamps together to get the reach I require. Now I can test fit the door dimensions. My original plan was going to require a deeper groove in the 3/4" top piece than I was comfortable with. I decided to employ some sliding door hardware. This meant the bottom groove had to be deeper and narrower (to accept the hardware track). Router plane to the rescue. The orignal plan called for a 3/8" wide lower groove. The hardware track calls for 1/4". I ripped down some scrap to glue in as a filler. The track will hide all evidence of this. Here's the lower guide pieces that fit in standard 35mm cup holes. I make up a dummy stile so I can be sure I've got the new dimensions right. Second times the charm. Now I can go ahead and finish sand the interior surfaces and pre-finish them. While they are curing I will build the doors. 7 Quote
Ron Swanson Jr. Posted October 25, 2024 Report Posted October 25, 2024 Always impressed with your meticulous work! Quote
Popular Post gee-dub Posted October 31, 2024 Author Popular Post Report Posted October 31, 2024 Thanks Doug. I appreciate the encouragement. I need to do the joinery for these dividers. These panels provide some minor structure but are really just to hide the compartment behind the sliding doors when they are closed to give a clean look. I grab a big enough piece of scrap ply out of the bin and do a mock up. The Matchfit sled makes these angle cuts really easy. A square lets me line thing up and clamp them down basically by eye. I check the fit and the door clearance. Cut the real blanks. I use some shop made clamping squares as stops for the Domino. I use a setup block as a stand off to give me the position I want. I use a plane stop and the same setup block to place the mating mortise. I use an off cut from the divider to help me square the odd shaped piece for mortising. The setup is a mirror image for the other divider. OK, I'm happy with that. Now can I finally start the door parts breakdown!?! 7 Quote
Von Posted October 31, 2024 Report Posted October 31, 2024 On 10/31/2024 at 2:02 PM, gee-dub said: I grab a big enough piece of scrap ply out of the bin and do a mock up. Thank you for showing this. Doing a mock up is a great idea and one I wouldn't of thought of. Quote The Matchfit sled makes these angle cuts really easy. A square lets me line thing up and clamp them down basically by eye. +1! Between my mini Matchfit sled, the t-tracks on my main sled, and an L-fence, I feel like the number of things I'm comfortable doing on the table saw has increased dramatically. 1 Quote
Popular Post gee-dub Posted October 31, 2024 Author Popular Post Report Posted October 31, 2024 On 10/31/2024 at 12:29 PM, Von said: Thank you for showing this. Doing a mock up is a great idea and one I wouldn't of thought of. Even though I do a fair amount of SketchUp and use it for detailed joinery studies I generally only use plans as (read as Capt. Barbosa from Pirates of the Caribbean) guidelines. I reach a point in any project where I start to measure off of the piece as opposed to off of the plans. Mock ups come in really handy for this . . . or maybe this is just how I justify scrounging old Ikea furniture off the side of the road. 4 Quote
Popular Post gee-dub Posted November 2, 2024 Author Popular Post Report Posted November 2, 2024 Finally breaking down parts for the sliding doors. I was lucky on this board. I found figure areas that yielded the top and bottom rail pretty easily. As you can see the stiles are at a bit of an angle. This is to get me the figure I want. You can often see furniture where the next part is just taken out of whatever happens to be in hand. This can give you figure that makes doors or drawers look slanted even though they are dead square. I used to wonder why there was so much spoil, percentage-wise, reported by seasoned furniture makers. Once I got my head around it their numbers made sense. I meant to show this in the previous post although I am sure I am preaching to the choir and sometimes just type to "hear" myself talk. ZCI's are great but the friction of spoil will widen the slots. If I want to use the slots for a reference mark during an operation BUT, don't want to replace the ZCI yet . . . I place some tape over the slots, run the blade through and presto . . . an exact reference of where the blade will cut. I take the measurements for the upper tongue off of the dummy part I made earlier. Feather boards and a push shoe help me control the material and make a clean cut. Some material likes to tear out despite sharp cutters and good technique. If I see this I just use a wheel gauge or a striking knife to score the material at the location I plan to cut. An extra minute or two of time can save you from re-making a part. I am a belt and suspenders guy. Even though I have laid these parts out and marked them I do one last orientation to check for how things look. Sapele, like cherry or white oak, has a lot of chatoyance. This means things can look very different from one point of view or another. That is not big deal unless you mix parts. Then you end up with a dark-looking top or bottom rail and a light-looking bottom or top rail no matter what angle you view it from. Once I am happy I confirm my markings. Your standard cabinet makers triangle markings will keep your parts identified through out the joinery process. Here's yet another use of the 1-2-3 block. A magnet captured in stage grip tape (or whatever you use) . . . Will stick to the tablesaw top as a stand off block for cross cutting. I set the fence 3" longer than the desired length of the part and confidently cut away. The dummy part (v2 shown here) acts as a story stick. This dimension is the exact length of my stile for the sliding doors. I roughly set the adjustable stop block, dial it in and make the cuts for both doors. Ta-Da! I like doing things in a way that keep even me from screwing things up 7 Quote
Popular Post gee-dub Posted November 4, 2024 Author Popular Post Report Posted November 4, 2024 I just wanted a look at the dry assembled frame in the carcass. These extrusions get used for many things; cove cutting on the table saw, fence extensions, and long stop positions at the router table. Here they serve that purpose. Anyone who has had a plunge cut at the router table turn into a javelin knows the value of a back stop when doing this sort of operation. All the frame parts get grooves; through cuts for the stiles, and stopped cuts for the rails. A few whacks with a butt chisel square out the ends of the router bit cut grooves. Floating tenons (dominoes in this case) make frame assembly pretty straight forward. The sliding door panels are wider than my jointer. This means I have to trudge out to one of the sheds and retrieve my age-old friend the planer sled. Once one surface is true you can plane the other side to parallel, I put marks at two perpendicular edges to let me know how far I can go in positioning the frame on the panel. I want a look that I like but don't want to wander off the reservation. Once I have the rough look I want I generally center the figure in the frame and mark it. I cut the panels to square and end up here. When doing machine work, setup bars can be helpful. Here I want a 3/8" depth on my wheel gauge to match the router bit I will use for the back relief on the panels. A cutoff from the original panel blank lets me confirm the back relief depth. I scribe the panel backs on all four edges to avoid tear out on the reversing grain material. I cut the relief, dry fit the panels and finally get a peek at what is starting to look like furniture ;-) We need to do some shopping but I will be back at it as soon as I can. 4 Quote
Von Posted November 5, 2024 Report Posted November 5, 2024 Your planer sled looks like it has a rope running down the middle? Would you mind explaining its purpose? TIA Quote
gee-dub Posted November 5, 2024 Author Report Posted November 5, 2024 It is the early Keith Rust version. The rope is a bungee cord to hold the leveling blocks. Shop Notes magazine # 137 has a more refined version. Planer_Sled_Rust.pdf 2 Quote
Mark J Posted November 5, 2024 Report Posted November 5, 2024 Clever trick with the set up bars. 1 1 Quote
Popular Post gee-dub Posted November 5, 2024 Author Popular Post Report Posted November 5, 2024 I am at the point where I need to pre-finish the door panel inserts. This means it is color sample board time. The two choices in the first pic have a more brown (blue) tint. The second pic has a more red tint. These do not look nearly as different from each other as they do in real life. LOML picked the right side of the second pic. It has a bit of red to pull toward the dressers and blanket chest as well as a bit of brown to pull toward the flooring. Whatever Lola wants . . . 4 Quote
wtnhighlander Posted November 6, 2024 Report Posted November 6, 2024 Don't quote me, but I'd bet the grain pattern of that sample skewed the preference. Those stripes are gorgeous. 2 Quote
Popular Post gee-dub Posted November 6, 2024 Author Popular Post Report Posted November 6, 2024 Base color pre-finish on the floating panels. SWMBO is happy so I'm happy ;-) 5 Quote
Popular Post gee-dub Posted November 7, 2024 Author Popular Post Report Posted November 7, 2024 Sometimes I ease edges with a small plane, sometimes with sandpaper, this time I will use a 1/16" round over bit. I sometimes clamp a frame together and run it around the bit at the router table. This gives me a kinda cool stopped profile via the bearing guide. I do a dry run before glue ups. This helps me be sure I have every thing I am going to need right at hand. And here's the real deal. I will let this set for about an hour and then do the other one. 5 Quote
Popular Post gee-dub Posted November 10, 2024 Author Popular Post Report Posted November 10, 2024 Had a bit of tearout on the reversing grain on this piece. A card scraper takes care of that pretty quick. A Millers Falls No. 9 puts a clean show edge on this divider panel. Here's one of those weird, inexpensive things that is a lot more useful than you thought it would be. A Milescraft Edge Sander with some 320 grit on it eases edges easily and consistently. All non-glue no-show surfaces and internal surfaces get a shellac sealer coat. I find using oil based finishes on enclosed surfaces leaves a smell for way too long. I tape off areas that will be glue surfaces. And so the finishing dance begins. No pics but I do have oil based colorant coats on several surfaces as well. 4 Quote
Popular Post gee-dub Posted November 11, 2024 Author Popular Post Report Posted November 11, 2024 Moving into one of those phases where I feel like I have done a lot but I don't really see anything . I don't know when I became such a wimp at working with long / heavy parts but it seems to have happened between the sideboard project and the headboard project . Enough whining. For the last 22 years or so I have been gathering clamps. It is nice to have a variety. This part of the assembly can set in the clamps while we entertain for a birthday. Then I can attach the top, start final surface prep and slap on some finish. I really cannot wait to get started on the side table (piers?). They are much more like the type of thing I enjoy working on but, they are pretty useless without the center console part of this headboard . 5 Quote
Mark J Posted November 12, 2024 Report Posted November 12, 2024 20 hours ago, gee-dub said: I don't know when I became such a wimp at working with long / heavy parts Yeah, tell me about it . What constitutes too heavy has been undergoing "deflation". This is going to be a substantial piece when you're finished. Does it disassemble for moving? 1 Quote
gee-dub Posted November 12, 2024 Author Report Posted November 12, 2024 @Mark J - It will be three pieces; the center console and each end fixture. They will each mount separately to the wall and then to each other. I will use french cleats so I can just have my neighbor help me lift them onto the cleats and then I will screw them to studs through rear bracing made for that purpose. I have used this method on other heavy items in the past with good long term result. Fingers crossed ;-) 2 Quote
Popular Post gee-dub Posted November 12, 2024 Author Popular Post Report Posted November 12, 2024 I broke my own rule and changed horses in the middle of the stream. I had planned on a plywood back but decided to go with the lap joint bead board shown earlier in the thread. Some of this will make better sense as I get farther along. The design change meant that my lower mounting cleat cannot be captured via mortise and tenon between the sides. I will switch to pocket holes at the ends and screws into the lower base panel along the length. I glue dominoes into the mortises that I had already cut into the mounting cleat and cut them flush. A block plane smooths these out the same way we plane dovetail ends or through dowels. The inset electrical service device did not come with a template so I made one real quick out of a piece of an old manila folder. If you don't have a self-healing cutting mat they are pretty handy. I pulled a bonehead maneuver and failed to put in the cutouts for the electrical devices before I glued the base panel in place. When I tried to learn to golf I learned that playing well is best but knowing how to recover when things go wrong is a valuable skill. With the vertical dividers in place I will have to cut them from below. I choose the location for the devices and mark them on the top of the lower panel. I place the template and use an awl to mark the four corner positions. A raking light helps my old eyes see the dimples. I drill 1/16" through holes at the corners to transfer the positions to the underside of the panel. I line up the template on the underside using the corner holes. I draw a white pencil line around the inside of the hole and take a jigsaw to it. The jigsaw effort is basically the same. It just would have been easier doing it at the bench before the panel was installed instead of sideways. And it looks like so. There will be one of these behind each sliding door. We have hearing aids, phones, and whatnot so I knew I wanted power built in as opposed to "exension-corded" in as we did in the old master bedroom. 6 Quote
Popular Post curlyoak Posted November 13, 2024 Popular Post Report Posted November 13, 2024 On 11/4/2024 at 11:31 AM, gee-dub said: The sliding door panels are wider than my jointer. This means I have to trudge out to one of the sheds and retrieve my age-old friend the planer sled. Sometimes the sled is the best answer. When I have a need for wide boards that I have a different answer. If there is some straight grain I'll rip it, dress both parts and glue them together. Then there is the benevolent beast. This tool resides nearby. I have earned access any time I want. In return I oversee the property when they leave for the hot summer. Both parties enjoy the trade. This machine has been completely overhauled. 12". If you look at the spot where the fence ends there is a small turned piece of wood. It is a mini ships wheel to raise or lower the bed. It is a joy to use! And that is where I can avoid the sled. 5 Quote
Popular Post gee-dub Posted November 14, 2024 Author Popular Post Report Posted November 14, 2024 @curlyoak - What a beautiful beast! I cannot believe how long this project is taking . I finally start installing the pre-finished back slats. As usual I use 1/8" strips to set the gap for wood movement. There we go. The rear lower cleat was going to be M&T attached. My shift from a plywood back to back slats made that untenable assembly-wise. As shown earlier I filled the mortises and drilled pocket holes. I use a shooting board / plane to fine tune the fit lengthwise. And there we go. Instead of a bunch of tenons I simply used screws in the proposed tenon locations plus a few extra for strength. We live in earthquake country and you never take mounting anything to the wall for granted. . This cleat cannot be glued except for the ends. Otherwise it would interfere with the seasonal movement of the slats. So here we are with the first finish application for the bulk of the piece. The back slats are darker since this is their second coat of finish. Tomorrow I will endeavor to persevere. <-- Josey Wales reference. 4 Quote
wtnhighlander Posted November 15, 2024 Report Posted November 15, 2024 @gee-dub, what dictates the width of that lower cleat? And since you mentioned earthquakes, do you add any method to lock the piece to the wall cleat? Quote
Popular Post gee-dub Posted November 15, 2024 Author Popular Post Report Posted November 15, 2024 @wtnhighlander - I was shooting for a width that would help the long open carcass deal with any racking under stress. When I changed the design of the back panel from plywood to slats I wanted something to back them up so it had to be at least big enough to come up past the bottom of the slats. Part of it was kind of like the "how wide do I make the stretcher on my table?" sort of thing. I knew I wanted at least 6" but the board was a bit wider and the spoil would have become scrap so I just used the whole 7-1/2" or so. The whole fixture will "hang" from a full width french cleat at the top, once hung I will drive screws through the cleat into the studs. The lower cleat will also be screwed into studs. The top horizontal and bottom horizontal are locked together via the sides and dividers so a fairly solid unit sharing supporting members throughout (I hope). The side piers will also hang from french cleats and connect to the wall via upper and lower cleats. The piers will also connect to the center console. I believe with this many distributed and interconnecting attachment points the load should be pretty well spread out. 2 1 Quote
Popular Post gee-dub Posted November 16, 2024 Author Popular Post Report Posted November 16, 2024 A lot of you know that I use an oil:varnish blend that I wipe on / wipe off similar to Sam Maloof and many others. The first coat (sometimes following a tint / color coat . . . so maybe second?) seals things, applies color evening, and normally cures in 24 hours here in sunny SoCal. The weather lately caused the finish to take an additional 24 hours but is ready for sanding today at 800 grit in preparation for coat number two. After sanding any nibs off I wipe all surfaces with a tack cloth which in this case is a paper towel sprayed with mineral spirits. Here is the second coat wet. Here is the second coat wiped off. The gloss varnish takes on a satin level gloss due to the wiping process. This is my preferred level of gloss for most things. I will apply coat three tomorrow or the next day depending on the weather and curing time. It is important that the previous layer of finish be hard-cured before you try to work it any further. Anyone who has tried to work a not-yet-cured or soft finish knows how things 'pill' and create a lot more work than just taking the day off and waiting. 6 Quote
Popular Post gee-dub Posted November 19, 2024 Author Popular Post Report Posted November 19, 2024 A little off topic but . . . related to the overall project. Having stated my defense I offer the following. We have a split-king with independently adjustable frames under each half of the bed for various reasons. LOML's matress is 1" thicker than mine since she likes a pillow top and I like "road side motel firm". The frames are adjustable but not in those increments(?). I made one of these for each of the six legs on my side. The beds get moved about a little during house cleaning so they need to be pretty stout. I make an insert core for each leg. The elevator disc gets glued and screwed to the core insert. And the original cap that prevents scratching fits over the new elevator cap. The bed(s) have a sort of floating appearance that LOML wanted to be sure did not get compromised. These additions will be stained black with Transtint and lacquered with a finish to match the gloss of the metal legs. they will not be invisible but, unless you are really looking for them they should go unnoticed )I hope, I hope, I hope). 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.