wtnhighlander Posted January 7, 2025 Report Posted January 7, 2025 Maybe a little different question than @roughsawn, but I sometimes wonder if the wedge shape of the panel, as drawn above, risks splitting the rail or stile if fitted a little too tight. I've tried it like you show, and also tried flattening the section that actually goes into the groove. No failures either way, but my sample size is fairly small. 1 Quote
roughsawn Posted January 7, 2025 Report Posted January 7, 2025 Ya, same question here...that's what I was getting at. Whenever I profile panels, I leave an "ear" 1/4" wide that slides into the grove in the rails and stiles. About 1/8" long, just shy of touching the bottom of the grove all the way around. Then stabilize with spaceballs. I see the edge of the wedge touching the edge of the groove, and no room for movement. I know that is not the case...thus my question as to where and how movement is accounted for??? Thanks gee-man. My next panels are going to have wedges. I like the simple design. I made several urn lids with a wedge top design, and they look great. 2 Quote
Popular Post gee-dub Posted January 7, 2025 Author Popular Post Report Posted January 7, 2025 @wtnhighlander - @roughsawn - Valid questions. On wider panels (maybe 10" plus) I do profile a flat tongue and use a 3/8" to 1/2" deep groove and space balls. For smaller panels (and possibly because I am in SoCal) I get away with a 1/4" deep x skinny-5/16" high groove and the profiles shown above. I do still take time of year into account. It is winter so I make the fit a bit loose. The silicone blobs (space balls) take care of keeping the panels centered, rattle-free, and the seasonal shifts. I haven't had a split yet and we all tend to move toward what works for us. I would not try this in Louisiana 6 1 Quote
roughsawn Posted January 8, 2025 Report Posted January 8, 2025 gee-man, how thick are your solid panels? 5/8"? 3/4"? Quote
Popular Post gee-dub Posted January 8, 2025 Author Popular Post Report Posted January 8, 2025 On 1/7/2025 at 5:17 PM, roughsawn said: gee-man, how thick are your solid panels? 5/8"? 3/4"? In the picture the panels are 5/8". On the current project they are 7/16" or less. This is a wall-hung, floating-look headboard so I cut the weight wherever I can. 4 Quote
Popular Post gee-dub Posted January 13, 2025 Author Popular Post Report Posted January 13, 2025 We have been without city power for days. I rolled a table over by the double doors and used good old fashioned solar power to see enough to continue gluing panels. Got our power back so I quickly rip to final width and crosscut to length. This is why I use task specific blades; knife edge cross cuts even in fibrous things like sapele. So there are the tops and pull outs. Grace under pressure, that's me . I was using a striking knife to put a center groove on a shop made drawing bow. I slipped and cut the string. New string. I layout the arc that I am after. I gang the parts together back to back. Since I am free handing the arc, if I am a bit off they will at least be a mirror image of each other. Rough it out at the bandsaw. Sand to the line at the edge sander. If you want to check that you have a fair curve you can rock the arc on its edge. There should be no stutters or flat spots. Final clean up is with a shave at the bench. LOML says it is time for lunch. 6 Quote
pkinneb Posted January 13, 2025 Report Posted January 13, 2025 Very nice! I am right there with you on the task specific blades for clean cuts! Quote
Popular Post gee-dub Posted January 14, 2025 Author Popular Post Report Posted January 14, 2025 On 1/14/2025 at 6:05 AM, Mark J said: Hopefully the power stays on! So far, so good. Going to pick up a generator in a few in case the . . . er . . . wind blows !?! Around here that's like saying their might be a hurricane this year in the south / southeast. In Cali it is not if there is going to be a fire season, it is when. Fires have been happening naturally and unnaturally in this region since the seas receded. It's like congress being surprised that "there's a budget due this year too???" 3 4 Quote
roughsawn Posted January 15, 2025 Report Posted January 15, 2025 gman, what is the material you made your marking bow out of? Picture looks like a strip of...cork? Quote
Popular Post gee-dub Posted January 15, 2025 Author Popular Post Report Posted January 15, 2025 On 1/14/2025 at 7:20 PM, roughsawn said: gman, what is the material you made your marking bow out of? Picture looks like a strip of...cork? That one happens to be single sided tempered hardboard. Dual tempered hardboard is better although I have a long one made out of 1/4" MDF. The dual tempered hardboard is more resilient and consistent but one doesn't often stumble across long narrow scraps of it and a full sheet will last you the rest of your life 5 Quote
Popular Post roughsawn Posted January 16, 2025 Popular Post Report Posted January 16, 2025 Thank you for the pictures. I'm gonna make one now. I just finished the live edge coffee table, and put a curve on all the 4" aprons. I jerry rigged a bow out of a 1/4" strip of hardboard...but used clamps on the ends of the aprons, and bent the strip around that. What a struggle. You are definitely the king of jigs! I'm learning...this woodworking game is all about the jigs!!! 2 1 Quote
Popular Post gee-dub Posted January 18, 2025 Author Popular Post Report Posted January 18, 2025 More incidental steps (but all lead to completion) . . . I needed to lay in a couple of mechanical fasteners that will help me when I am hanging this rig on the wall and doing final assembly. I needed to be pretty spot-on with the locations of these so I took a few minutes and made a drill-guide block. Here's my victim. The problem here is I am joining a couple of separate carcasses on a "top" that has grain running perpendicular. I need to allow for movement and also affix the two carcasses together. This means I have visible elevations that I want to remain consistent. The movement has to take place to the hidden side and rear. I do the layout and then use an awl (made for me by my dad) to dimple the locations. I put a screw through the jig with the tip just poking out. I will register this screw tip in the dimple to locate the "jig". Square it up. Clamp it on and back the screw out. Drill the hole. I should mention that I put a backer block behind this area to assure a clean exit hole. This is not the actual fastener but it does demonstrate what I am after. In other news I am applying the shellac sealer to the interior areas of the cabinets. I know I have mentioned using shellac for interior areas that will store clothes. It gasses off pretty quick and by the time I apply a top coat and it cures there will be no danger of clothing stored in the cabinets of getting stinky due to oil based finishes. 5 Quote
fcschoenthal Posted January 18, 2025 Report Posted January 18, 2025 Glenn, you always seem to go the extra mile on your projects. I find myself too many times using the practice of GETMO (Good Enough To Move On). 2 Quote
Popular Post gee-dub Posted January 19, 2025 Author Popular Post Report Posted January 19, 2025 @fcschoenthal - I definitely have some pieces in my own home from early on where I did things or let things go that I never would on a commission. Now that I mostly make things for myself and am retired I can take the time to futz around more with the little things. 4 Quote
Popular Post fcschoenthal Posted January 19, 2025 Popular Post Report Posted January 19, 2025 On 1/19/2025 at 11:07 AM, gee-dub said: Now that I mostly make things for myself and am retired I can take the time to futz around more with the little things. I've been retired a couple of years and only make things for family. I find my wife has more projects and a stricter timeline than any of my former employers, hence the GETMO. My pieces aren't showroom quality, but figured out a long time ago that my family only cares that I made it (and that it's free), and don't notice the things that are off that I do. 4 Quote
Coop Posted January 20, 2025 Report Posted January 20, 2025 On 1/19/2025 at 4:56 PM, fcschoenthal said: My pieces aren't showroom quality, but figured out a long time ago that my family only cares that I made it (and that it's free), and don't notice the things that are off that I do. Ain’t that a neat deal!! 1 Quote
Popular Post gee-dub Posted January 21, 2025 Author Popular Post Report Posted January 21, 2025 Just a quick check in. I'm working the edge profiles and wanted to show what I call the Garrett Hack frame joint. I mentioned this earlier in the thread. I ran some pencil lines here to exaggerate the joint. Before profiling the seam is still visible but not bad. Once the corner edge is chamfered or rounded the seam all but disappears. 4 Quote
fcschoenthal Posted January 21, 2025 Report Posted January 21, 2025 On 1/21/2025 at 11:31 AM, gee-dub said: Once the corner edge is chamfered or rounded the seam all but disappears. I'm assuming that the amount of material left on the outside joint is equal to the chamfer width you plan on using. Brilliant for not having any joint lines. I'll probably have to practice that a couple of times to remember to use it in a project. I've also seen someone leave just the outside layer on plywood to cover the plys on the joint. They were cutting on a CNC, so no issue with the thickness. I'd have a hard time keeping the thickness consistent enough to look worthwhile. 2 Quote
gee-dub Posted January 21, 2025 Author Report Posted January 21, 2025 @fcschoenthal - Correct. 1/8" overlay with an 1/8" chamfer or roundover. 2 Quote
curlyoak Posted January 21, 2025 Report Posted January 21, 2025 On 1/21/2025 at 5:45 PM, gee-dub said: with an 1/8" chamfer or roundover. I have made the same joint with the face 3/8" thick and a matching chamfer. it hides the joint. 2 Quote
gee-dub Posted January 22, 2025 Author Report Posted January 22, 2025 @curlyoak - Yep, 3'15" here: https://www.finewoodworking.com/2012/08/07/2-face-frames-grooves-and-dadoes although mine is opposite. Quote
Popular Post Chestnut Posted January 22, 2025 Popular Post Report Posted January 22, 2025 Do you have issues getting the glue line to close really nicely? Without diligent clamping or cauls would that 1/8" lip have enough stiffness to close all the gaps? That's a great idea. I'm in the planning stages of a full set of kitchen cabinets so I'll be borrowing that soonish. Edited to say thanks. Thanks Gee-dub for being an awesome resource on this forum. It's a pleasure being able to look over the shoulder of a master. 3 Quote
Popular Post gee-dub Posted January 22, 2025 Author Popular Post Report Posted January 22, 2025 I don't know about being a master of anything outside of baiting hooks . Clamping cauls are certainly a benefit. I had some pecan left over from a project and made some curved cauls out of that. Never been sorry Made a little rack for them and some riser blocks that I use for panel clamping. 4 2 Quote
Popular Post curlyoak Posted January 23, 2025 Popular Post Report Posted January 23, 2025 I finally found the picture. I accidentally found this joint. I initially intended to have a rabbit joint. Then a light bulb went off in my head. I've repeated this joint many times. 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.