Popular Post gee-dub Posted December 7, 2024 Author Popular Post Report Posted December 7, 2024 Ruler stops; ya gotta love ruler stops. Unfortunately the most useful I have found were offered by Garrett-Wade back in the day and do not appear to be currently offered. There are some big clunky versions from several vendors currently available. These help me set the mid-rail position accurately by referencing off the stop and the end of the rule. Time to resaw out some floating panels from this 8/4 x 11"+ x 10' board. I use my jig saw to break these down to more manageable sizes. The planer sled comes into service again. Resawing this 11"+ wide board is at about the limit of my bandsaw. I can pull three panels from the 8/4 thickness of these blanks. Due to the resaw pattern I yield a center piece with a book-matched piece on each side. Now I get to pick who goes where in the grand scheme of things. One of the anomalies of sapele is the reversing grain. The cross pattern (?) is one that can be a problem at times. Sometimes this cross-pattern (I do not know the formal term) can be open and require filling or avoiding. Once I am happy with who goes where I can cross cut things to length. These shop-made flip-stop blocks are milled square. Even so when I am doing final dimensional work I check and re-check things. Once the long section is cross cut I flip the true edge to the stop and cut the shorter piece to length. I mark each of these to keep the sections together as I continue to break things down. The next phase will be ripping to width and profiling the panels. 4 Quote
Popular Post gee-dub Posted December 8, 2024 Author Popular Post Report Posted December 8, 2024 Glad to finally be getting my energy back. I got in a couple hours before breakfast this morning. Your typical cabinet maker's marking triangle helps me keep things re-aligned after milling. I usually like to raise my panels by hand (it's one of the few things I can do decently by hand ) but there are a lot of panels in this piece and I am getting behind. I will use the tablesaw to remove the bulk of the waste. I use some scrap from the ripping-to-width process to confirm I am getting the angle, width-of-raise, and thickness of edge I am after. You have all seen this tall fence rig I built years ago. It acts as everything from a tall router table fence to a raised panel jig it seems. Anyway, I end up here. These will all see some love from the hand planes before they get pre-finished. We all know to pre-finish our floating panels so that seasonal changes don't create a peek-a-boo exposure of unfinished wood when things shrink in the winter. Here's the general look of one of the side panels. My tummy says it is time for breakfast so I'm gonna go do that. 4 Quote
Mark J Posted December 8, 2024 Report Posted December 8, 2024 Just an observation, your marking triangles on the show side get partially cut away with the bevel cut. Do you also mark the back sides? Also, any reasons that one would choose the TS over the router table for this operation (or vice-versa)? 1 Quote
Popular Post gee-dub Posted December 8, 2024 Author Popular Post Report Posted December 8, 2024 @Mark J - Good catch! I actually added a longer triangle to one of the blanks as I noticed the triangle was going to get destroyed. Even though it ended up as only a partial after the operation, as long as there is enough to match up, I'm good. As to taking a 14* bevel, 1" long, at the router table as a crosscut . . . IMHO the 3HP tablesaw does a better job. At a shaper? Heck yeah! There are some cuts where raw horsepower really makes a difference. I love my 2HP bandsaws but, if there was a way to easily upgrade them to 4HP+ I would do it in a heartbeat . Sorry . .. I digress into horsepower envy. In a previous life I was in sound reinforcement. I can guarantee you that 500 watts per channel (although staggering in your living room) is nothing like 100,000 watts per channel in an amphitheater . Another situation where technology is wonderful but, raw horsepower is something else . . . think muscle car . 5 Quote
Popular Post gee-dub Posted December 11, 2024 Author Popular Post Report Posted December 11, 2024 I've been unable to post to the forum for a couple of days due to technical difficulties. Not sure if others experienced this; maybe its just me(?). I found that gang-clamping these panels together with a bowed caul let me plane the bevels all together for consistency. Some sanding is required here and there and I thought I would show that I pre-cut a bunch of grits to size for my sanding blocks. That way when I am in full-throttle mode I can just grab a few sheets out of the drawer. Anyway . . . here is the base color coat on several of the panels that will be used. . This is a good place to stop and let the finish cure for a while. We planned to start setting up Christmas decorations today so it all works out. 5 Quote
fcschoenthal Posted December 11, 2024 Report Posted December 11, 2024 I love the way sapele looks. Nothing warmer. Quote
wtnhighlander Posted December 11, 2024 Report Posted December 11, 2024 Looking goid, @gee-dub! FYI, you weren't the only one noticing difficulties with site access. Hope it is all straight now. 1 Quote
Von Posted December 11, 2024 Report Posted December 11, 2024 On 12/10/2024 at 11:59 PM, wtnhighlander said: Looking goid, @gee-dub! +1 On 12/10/2024 at 11:59 PM, wtnhighlander said: FYI, you weren't the only one noticing difficulties with site access. Hope it is all straight now. FYI, It is from time-to-time very slow for me, but I've not seen an outright failure. No issues in the last couple of days. Quote
Mark J Posted December 11, 2024 Report Posted December 11, 2024 13 hours ago, gee-dub said: I've been unable to post to the forum for a couple of days due to technical difficulties. Not sure if others experienced this; maybe its just me(?). I had similar problems for a day or two, but only on my Android. PC was OK. Quote
Popular Post gee-dub Posted December 13, 2024 Author Popular Post Report Posted December 13, 2024 I made the panels pretty close tolerance-wise. This one was too close so I had to shave a bit more off and re-color. While I wait for that to dry I glue the rails to the last panel stile. Gluing one side at a time helps me get the rails good and square to the stile. The adjacent stile then pretty much self-squares. Then I slide the panels in and attach the other stile. Now all the side panels are glued up. I'm sure I've mentioned this before. When you are doing an epoxy job, mix a little extra and fill in your worn ZCI's. A strip of packing tape on the top allows you to pour in the extra epoxy from the back. You can then re-cut your ZCI opening. Not perfect but definitely serviceable. I use a sac-fence for this dado cut. I also use a raised panel feather board. These arced feather boards place the down pressure on the portion of the material that is not being milled. This prevents tipping. The rabbet in the face frame allows the side panel to seat well. Once in place the vertical grain of the sapele makes the joint almost disappear. I tend to call this a Garrett Hack joint since that is where I learned it. I have used it with good success on many pieces. Here's an example on a dresser. It gives the impression of a thicker side member although it is actually a 90 degree joint of 3/4" pieces. 3 Quote
BillyJack Posted December 14, 2024 Report Posted December 14, 2024 I take it you don’t want a router setup to do door panels? Quote
Popular Post gee-dub Posted December 14, 2024 Author Popular Post Report Posted December 14, 2024 @BillyJack - I have done them that way with good success. My designs tend toward a fairly simple raised panel profile so the bevel cut on the tablesaw or a quick run with a hand plane has become my usual. If I was doing more than just the few items I have planned for my own home, a router bit setup would be the way to go. My Woodcraft ogee set has set lonely in the drawer for years . . . I should probably sell it cheap to someone who would use it. Sorry for the sort of incremental update. I hardly ever do shelf pins. I do them so seldom that I have bought a new house and built a new shop since the last time I needed a shelf pin jig. By now mine is helplessly lost somewhere on the property; I picked up the Kreg version which seemed reasonably priced for someone who uses one as often as I do and based on what you get. Most of what I have ever made has been one-off custom stuff. This is even more true now that I only make stuff for our home. This means the well established standards for shelf pins, hinges, and drawer slides rarely apply. Due to my rare use and therefor minimal experience with this basic furniture feature I wanted to see some pencil marks before I started drilling holes. My Dixon long nose pencil barrel is probably some very reasonable metric dimension. Being an old stroker I think primarily in imperial and the snout would not fit into the 1/4" shelf pin holes (let alone the smaller 5mm versions). I don't know where I get this confidence but I have never shied away from modifying things to meet my needs. I reduced the diameter of the snout with files and sandpaper. I have some differing setbacks from the leading edge of the material that will receive holes. The front has to account for a 5/8" setback for the rabbet-like joinery. The rear needs to account for clearance for the 3/4" french cleats and a 1/4" birch plywood back panel. I am a big fan of figuring all this stuff out and then using setup blocks to make sure I don't get "creative". I use the usual vise-grip style clamp when the jig references off the built-in fence. For the rear (greater offset) I use a Bessey mighty mini and the outfeed / assembly table. It is amazing how often having a known flat surface with lots of dog holes and slots cut into it comes in handy. At any rate I manage to get one set of holes in the right place on both verticals. Three more to go; should be easier now that I have a process. 5 Quote
BillyJack Posted December 14, 2024 Report Posted December 14, 2024 One of stuff is common. Why someone throws one of jigs on a wall and collects them is beyond me. Some of my jigs are common and can be used in various builds.. Those should be kept. I use to make raised panels on the saw, but I stopped when I moved up to router bits.. When I hear someone made something hand made, I know everything is hand made.. Quote
Popular Post gee-dub Posted December 17, 2024 Author Popular Post Report Posted December 17, 2024 Just some time consuming sub-assembly glue up going on. I've never been sorry for collecting a gazillion clamps over the decades. This guy is waiting in the wings. Once the other upper carcass is glued up I will set them aside and start on the drawer boxes. 4 Quote
Popular Post gee-dub Posted December 20, 2024 Author Popular Post Report Posted December 20, 2024 Still loping along . . . I have some freebie plywood from a local cabinet shop. It is in odd metric thicknesses like a lot of K&B stuff. I laminate some 1/2"-ish pieces together. I can then mill these to what we here in the U.S. call "normal" imperial dimensions. I turn these blanks into French cleats at a 3/4" thickness. It is such a bother when you have been through the full material milling process to get four of something only to realize you actually need eight. Recovering my composure I finish milling out the frame parts. Next is a whole lotta mortises. Ever onward . . . BTW, I find it relaxing to listen to something soothing while mortising . . . like this for example. Michael Romeo . . . seriously!?! BTW, I also love Glenn Gould and John Coltrane 3 1 Quote
Popular Post gee-dub Posted December 21, 2024 Author Popular Post Report Posted December 21, 2024 After cutting a boat-load of mortises I need to groove some frame members for the floating panels. A typical stopped groove for the stiles on the drawer carcasses. For the top and bottom rails there is a dual stopped groove. The reason for this extra step is to allow a good amount of material around the mortise for the center dividing rail. An inexpensive ruler stop makes setting up the mirror image groove a snap. You use the first stop block as a reference point; then set up the alternate stop block. Then remove the initial stop block to complete the operation. Here's the end result of all this song and dance. And the end result of all the slot cutting mambo. Alright. Let's make some floating panels. 4 Quote
Popular Post fcschoenthal Posted December 21, 2024 Popular Post Report Posted December 21, 2024 I hadn't thought about using a ruler stop to duplicate the opposite sides. This old dog learned a new trick. Hopefully I can remember it the next time I can use it. That's the other problem with old dogs. 4 Quote
Popular Post gee-dub Posted December 23, 2024 Author Popular Post Report Posted December 23, 2024 I like panels to be bookmatched when possible so I cut these lower drawer cabinet panels from a common blank. Typical rip to width. And crosscut to length. I gang the parts to raise the panels. I apply a base color coat prior to assembly. This just makes sure no unfinished areas peek out during seasonal wood movement. 6 Quote
wtnhighlander Posted December 24, 2024 Report Posted December 24, 2024 @gee-dub, how do you deal with the difference in book-matches that results from the grain entering / leaving the show surface at opposing angles? My experience has revealed rather startling color and/or chatoyance variation when the two faces of the match are joined side by side. My last big project has one panel with a 'black eye' and a 'white eye' because the book-matched halves reflect light in opposite directions around a knot-swirl figure. 1 Quote
Popular Post gee-dub Posted December 24, 2024 Author Popular Post Report Posted December 24, 2024 @wtnhighlander - It is unfortunate that I sometimes find a surface I really want to use but the grain direction makes the post resawing match poor. It seems that quarter-sawn material lends itself to better book matching. There will always be some deviation due to the material removed by the saw kerf and figure direction. I keep a Woodslicer (narrow kerf blade stock) handy for times when I really, really want a certain piece of material, the figure on it I mean. The narrow kerf of the Woodslicer helps things match up better. A more quarter-sawn material is often a better / easier answer in my experience. I have a couple of pieces in the house that it took me a while to get comfortable with the difference in "look" based on angle of the material; cherry, walnut, and others. 3 1 Quote
Popular Post gee-dub Posted December 28, 2024 Author Popular Post Report Posted December 28, 2024 Gluing up side panels. I tend to clamp panels from the sides and also flat to a reference surface. Need some grooves for a bottom panel that will be 1/4" BB ply. This is a structural element and will not be visible unless you are laying on my bedroom floor. Only I get to do that after too many barley-pops but, I digress . . . I put some reference marks on the fence in pencil. These are easily erased and work well when I just have a few cuts to make and don't want to change over to the longer fence faces. The idea is to be able to know where to start or stop the cut (the opposite sides are mirror images) to allow the plywood to fit without blowing the groove out the front of the drawer box. A piece of scrap lets me make sure I am in the range I am after. This right angle fixture comes in handy for a lot of things. In this case it lets me control the tall panel when plunge cutting the starting point for the right hand panels. The result is a nice pair of mirror image grooves. 6 Quote
Popular Post gee-dub Posted January 5, 2025 Author Popular Post Report Posted January 5, 2025 Using some 'B' grade (no knots or patches, one face) baltic birch ply for the rear panels of the upper cabinets. I tend to cut the blank a bit oversize, confirm one side is flat and then cut the final width. I have no problem slicing a 1/32" strip off the side of a panel. The effort in setting up your saw pays dividends year after year. Smaller panels from 'BB' grade baltic birch ply that will be in a no-show position at the bottom of the drawer cabinets. Obviously missing drawers, drawer cabinet tops, pullouts and so forth but you can finally get the drift of where these piers are going. LOML is happy and I will start gluing up solid panels for the tops, pullouts, and so forth. 5 Quote
roughsawn Posted January 7, 2025 Report Posted January 7, 2025 Glen, your work is so far above my pay grade, I think I'll just keep lurking. Looking awesome! Quick question...when you cut your 14 degree bevels on your panels, how do you determine how and where they will reference in the dados in the rails and stiles? It looks like the bevel, at some point, just makes contact with the inside edge of the rails and stiles, and just butts up and stops there??? I know you have room inside for movement, and maybe even have spaceballs inside. But, how do you figure where the panels meet the frame, and how much room for movement? 2 Quote
Popular Post gee-dub Posted January 7, 2025 Author Popular Post Report Posted January 7, 2025 I generally make two calculations; how thick the edge will be (usually 1/4" and how much exposed "raise" I want to see (usually about 1"). The angle will vary with the panel thickness like so . . . This is a 1/2" and a 3/4" panel with a 1/4" edge and a 1" bevel. I will routinely draw the "look" I am after on the side of a panel . . . . . . and adjust from there. I do have space balls and sometimes use them in 3/8" deep dados. These happen to be 1/4" dados so I put blobs (I know, very technical term) of silicon rubber in the dados. Two blobs on every side (at least) and then position the panel for center. 24 hours later . . . ta-da . . . custom fitted space balls. Did that make sense? Sometimes I am not sure if I am answering the question 4 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.