Popular Post wtnhighlander Posted November 20, 2024 Popular Post Report Posted November 20, 2024 So you can take down the sign above your headboard now? 6 Quote
Popular Post gee-dub Posted November 20, 2024 Author Popular Post Report Posted November 20, 2024 Wipe on / wipe off of the final top coat. I add a little more varnish to the blend for this coat to be sure I have enough film. Woods like sapele, the oaks, pecan, shedua, and others have a pretty open pore structure so the final coat requires a bit of tending. I try not to "flood" surfaces but I do set a repeating 20 minute timer to return and check for weeping. As it turned out that was a good idea on this phase as I got some weeping on an area of reversing grain on the top and along one side of one of the doors. This is no big deal as long as you deal with it. A little wipe with a rag to remove the excess is all it takes. Where you get into trouble is if you don't check back and the finish starts to cure with the weeping still present. 6 1 Quote
Popular Post gee-dub Posted November 22, 2024 Author Popular Post Report Posted November 22, 2024 For the side pier build I decided to continue on in this thread even though it is swelling to the size of War and Peace. In my defense I did have COVID mid-build and that made this waffle about a bit. Be that as it may . . . I have some relatively straight grained ribbon sapele that I will use for the frame parts. The side piers have a lot of frame and panel construction so I need a lot of frame material . When I did my re-org on the lumber racks I left this stuff on top in a rare forward-thinking event . These pieces will yield the door frame rails and stiles. I am using overlay doors and drawers on this piece which is different for me; I normally favor inset. This means the doors and drawers will be focal points and as such will be pulled from the same boards and book matched wherever possible. I realized I had a good board for all of the door frame parts after already marking it for other use. One of the good things about marking rough parts with chalk is that when you change your mind a damp paper towel cleans everything right up. After choosing the source material it is just the same old, same old milling process. I get the door frame parts. And some of the frame parts for the pier sides. I am under no illusion that I can control wood's movements after being ripped or resawn. Despite this I do clamp or plastic-film parts groups and tag them with felt pen and tape to help me keep track of these larger projects. 4 Quote
Popular Post Mark J Posted November 22, 2024 Popular Post Report Posted November 22, 2024 Consider this a suggestion for some future build journal. I think it would be interesting to see how you go from plans to figuring out what pieces you need, and then how you go about deciding what board to use for which pieces and how to lay them out. If I did much flatwork, I think those are the kinds of decisions that would leave me paralyzed. 2 1 Quote
Popular Post Coop Posted November 23, 2024 Popular Post Report Posted November 23, 2024 Ahhh! Earthquake country. I remember when our bedroom could be described as that! 5 Quote
Popular Post gee-dub Posted November 25, 2024 Author Popular Post Report Posted November 25, 2024 So the center console is rubbed out and waxed. The door hardware provides a nylon roller that rides against the nylon track at the bottom. The depth is adjustable which is nice for fine tuning the reveal. I run some paraffin along the tongue that will ride in the top groove. So we end up here . . . The doors move really smoothly with the 35mm hardware and track. I did find buying the hardware and track was more cost effective from a cabinet hardware source than from somewhere like Rockler . . . Just FYI. 5 Quote
pkinneb Posted November 26, 2024 Report Posted November 26, 2024 Those panels are AWESOME!! 1 1 Quote
Popular Post gee-dub Posted November 26, 2024 Author Popular Post Report Posted November 26, 2024 I added bumpers to the outer edges of the doors as I found the "clunk" disturbing. Usually a neighbor or my buddy Dan are around to help out. With the holidays support personnel are scarce. I grab some scrap plywood and knock out a couple of "third hand" thing-a-ma-bobs. I name them Dan-1 and Dan-2 after the Cat in the Hat's Thing-1 and Thing-2. They do Dan's job and I don't have to listen to him talk smack . I mark the stud positions and take the cleat to the shop for drilling. Ten #10 screws in the top cleat with ten more planned for the bottom cleat . . . I think it will be OK. I'm gonna break for lunch and then contemplate hanging the beast. 4 Quote
Mark J Posted November 26, 2024 Report Posted November 26, 2024 That's gotta be a two person job. Quote
wtnhighlander Posted November 27, 2024 Report Posted November 27, 2024 Slick little helpers ther, @gee-dub! Did you do anything special to keep the from slipping on the hardwood floor? 1 Quote
gee-dub Posted November 27, 2024 Author Report Posted November 27, 2024 On 11/26/2024 at 4:58 PM, wtnhighlander said: Slick little helpers ther, @gee-dub! Did you do anything special to keep the from slipping on the hardwood floor? Wrapped the ends with painters tape and that seemed to do it. I had more tape on hand in case I needed to tape things to the floor. 1 1 Quote
wtnhighlander Posted November 27, 2024 Report Posted November 27, 2024 I bet some sport wrap would work incredibly well, if painter's tape didn't grip well enough. https://www.amazon.com/Breathable-Adherent-Athletic-Elastic-Cohesive/dp/B07WWW4KS6/ref=asc_df_B07WWW4KS6?mcid=fd56f071952a369681fda369114ad2b6&tag=hyprod-20&linkCode=df0&hvadid=693651996446&hvpos=&hvnetw=g&hvrand=7166882606338544994&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=1026012&hvtargid=pla-839494269029&psc=1 1 Quote
Popular Post gee-dub Posted November 27, 2024 Author Popular Post Report Posted November 27, 2024 Here’s a quick video showing the chatoyant effect. 4 Quote
Popular Post gee-dub Posted November 27, 2024 Author Popular Post Report Posted November 27, 2024 Here's where we are so far. LOML is looking forward to getting rid of the TV tray as a side table 7 Quote
Coop Posted November 28, 2024 Report Posted November 28, 2024 Darn! From shop to service in just a few hours. Very well done. 1 Quote
curlyoak Posted November 28, 2024 Report Posted November 28, 2024 An heirloom as always gee-dub! It needs to be signed dated! 1 Quote
Mark J Posted November 28, 2024 Report Posted November 28, 2024 Looks good already. It will be super when it's finished. Is the bed anchored so it won't move if you're sitting up and leaning against the headboard? Quote
gee-dub Posted November 28, 2024 Author Report Posted November 28, 2024 On 11/28/2024 at 6:43 AM, Mark J said: Looks good already. It will be super when it's finished. Is the bed anchored so it won't move if you're sitting up and leaning against the headboard? The bed frames adjust independently for TV, reading, leg elevation, and so forth so that shouldn’t be an issue. The frames are surprisingly heavy and seem to stay put. I do have hardware to attach them to the wall if that becomes an issue. 2 Quote
Popular Post gee-dub Posted December 4, 2024 Author Popular Post Report Posted December 4, 2024 The long and winding tale . . . I rip some more frame material at the bandsaw. I have shown these before but I find it helpful to take blown up screen shots of smaller details when turning blanks into final dimensioned parts; my memory is not what it once was. This is also helpful for joinery dimensions. After the oversize blank breakdown it is milling as usual. I do a lot of dry fitting at this stage because I tend to measure parts off the assembly as opposed to off the plans. I need a lot of frame parts for this piece. A board that suits my color requirement is a bit longer than I have room for. I planned the shop for a maximum of workspace as opposed to a more specific tool clearance. A couple of times a year this doesn't work out. The rest of the year I enjoy all the room I have to work in . The fit in this case is close enough that I remove one of my grinding wheel rests. This lets me lay in this board. and clear the blade by this much. End result is I get the cut I am after. I then break down those blanks and mill them square. As long as you end up square and true, life is good. I am going to knock off for now and pick it up in the morning. 4 Quote
wtnhighlander Posted December 4, 2024 Report Posted December 4, 2024 That's known as 'cutting it close', right? @gee-dub, is that sled base made from 3/4" stock, or something thicker? Quote
gee-dub Posted December 4, 2024 Author Report Posted December 4, 2024 @wtnhighlander - All of my crosscut sleds for the tablesaw have 3/4" BB ply bases except the taper jig (and a coping jig for the router table). The taper jig was made back in the day and has 3/4" BB ply with a laminated 1/8" hardboard for the t-slots. The coping sled has a 1/2" base with a commercial aluminum miter bar. No great plan on either of these. It is just how they turned out. 1 1 Quote
Popular Post gee-dub Posted December 5, 2024 Author Popular Post Report Posted December 5, 2024 I keep getting surprised by how many parts and steps are involved in this thing. I started getting lost so I built a quick spreadsheet to list components and their status. Years ago I standardized on 4 bin sizes for my storage; a 58 quart bin from Wal Mart, the bin shown below from Costco, a shoe box sized bin from Home Depot and Plano tackle boxes from wherever Plano is sold. The Costco bins let me gather small accessory items together in a place where I know they will be when I want them. In this case the Bosch Jig Saw and Domino flotsam and jetsam end up together. It may seem odd but it works. the Domino table comes with a variety of doo-dads as does the 1591 jig saw that I love so much. They all live here. I lay out the face frame parts and arrange as intended. This is my chance to make any last minute position changes before joinery commences. I then flip the assembly so I can mark it from the rear. The reason for this is that the front face is the reference face and when using the table the reference face is rested on the table surface. Granpa's old cross peen hammer is used as a micro-adjustment tools to position parts just where I want them. I then mark for the domino mortises. Again surprised by how may parts are in this thing . . . I haven't even started the drawer carcass yet. I do a dry run before glue up. I find this reduces my blood pressure during glue up. This is where you find out all those pesky little details that cause you grief when wet glue is in play like removing the little red clamp pad so that the clamp jaw fits under the table raising mechanism on this table. The face frames are glued and in the clamps which looks just like the dry run pic above. While these are setting up I will start grooving the side frames to accept the raised panels. 6 Quote
Popular Post gee-dub Posted December 5, 2024 Author Popular Post Report Posted December 5, 2024 We all tend to recommend those things that work for us. Just because they work for us does not mean they are for everyone. The Grr-Ripper has been a part of how I think about and perform operations for many years. Sorry if I sound like an info-mmercial for them. They excel at handling small parts, especially multiple operations with small parts. Here I am cutting the grooves in the rails for the frame and panel sides of this piece. For the longer stiles I place witness marks at the start and stop points for the stopped grooves. I plunge the cut at one mark . . . . . . and cut the groove till the next mark. And there we go. I started early today and after these many repeated operations I think I am done for today. Tomorrow is "resawing-the-floating-panels" day. 6 Quote
Beechwood Chip Posted December 6, 2024 Report Posted December 6, 2024 I used to use the Grr-Ripper a lot, but I like my blade guard for dust collection and safety. So, now I only use the Grr-Ripper when I take off the blade guard and switch to the riving knife. Wish there was a way to have my cake and eat it, too. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.