curlyoak Posted August 19, 2024 Report Posted August 19, 2024 On 8/19/2024 at 8:18 AM, gee-dub said: Yes. Even when material comes S2S or better I still run it through the milling steps to assure parts are square and true. For material too wide for my 8” jointer I use the planer sled. My jointer is also 8". Sometimes I will rip and glue it back. If necessary a friend in the neighborhood has a 12". It is old but completely rebuilt. An amazing tool. I call it the benevolent beast. To adjust the bed there is a mini ships wheel. Mine to use whenever I need to. They are snow birds meaning they leave during the hot summer. I have the key and permission to use the shop. gee-dub, from knowing you and your approach I expected you would true the lumber. Many people would use the wood as you bought it. Been there and won't go back. Quote
BillyJack Posted August 19, 2024 Report Posted August 19, 2024 “Many people would use the wood as you bought it.” Many do when the lumber is correct to start with. There is no reason to over process wood, but in your shop your free to do as you wish. Why I buy wood S3S. This way I don’t waste time processing and spend more time building. Now is processing brings you enjoyment, by all means do it.. My training probably conflicts with many other opinions, but hard to change Quote
BillyJack Posted August 19, 2024 Report Posted August 19, 2024 When I started at Commercial Millwork & specialty company(still in business) in 1983, all lumber came in rough. We had a warehouse full of shipped in lumber and forklifted. So I’m very familiar with trueing lumber. Skipping forward to 2010 all lumber at the furniture company was brought in fully processed. No time to processing wood. Quote
wtnhighlander Posted August 20, 2024 Report Posted August 20, 2024 I think if the pre-milled lumber was kiln dried, chances are good that it will remain true and flat. We hobby woodworkers sometimes err on the side of caution, and mill to machinist's tolerance, but that isn't always necessary. A large percentage of my stock is air dried, and even if I get some detectable movement after milling, it is very rarely enough to interfere with assembly. 2 Quote
curlyoak Posted August 20, 2024 Report Posted August 20, 2024 It is worth the time to build a true foundation. If it is true, raising the building will be so much easier and a lot more fun. Dressing lumber is the foundation of the furniture. 2 Quote
Popular Post gee-dub Posted August 21, 2024 Author Popular Post Report Posted August 21, 2024 On 8/19/2024 at 5:10 PM, wtnhighlander said: I think if the pre-milled lumber was kiln dried, chances are good that it will remain true and flat. We hobby woodworkers sometimes err on the side of caution, and mill to machinist's tolerance, but that isn't always necessary. A large percentage of my stock is air dried, and even if I get some detectable movement after milling, it is very rarely enough to interfere with assembly. Oh believe me . . . if a blank passes the bridge (arcing) or rocking (teeter-tottering) test on a reference surface I skip the face or edge jointing step. I do err on the side of caution but try to be reasonable. It took me many years to learn what to ignore. Some things that I used to automatically deal with early in the material prep stages now get ignored because I know that section of the blank is going away somewhere in the process anyway. I think we get a better vision of the end-game as we gain experience and we learn what we can ignore and what is critical to the next operation. 4 Quote
BillyJack Posted August 21, 2024 Report Posted August 21, 2024 On 8/19/2024 at 10:03 PM, curlyoak said: It is worth the time to build a true foundation. If it is true, raising the building will be so much easier and a lot more fun. Dressing lumber is the foundation of the furniture. Dressing lumber is the foundation , I would question. There is no need to over process wood because you can. You can’t take a flat board and make it flatter? Or Am I missing something? Quote
gee-dub Posted August 21, 2024 Author Report Posted August 21, 2024 On 8/21/2024 at 11:54 AM, BillyJack said: Dressing lumber is the foundation , I would question. There is no need to over process wood because you can. You can’t take a flat board and make it flatter? Or Am I missing something? Not in my opinion. If blanks, once reduced to "oversize" have an edge or a face that are true, I will use that. Quote
curlyoak Posted August 22, 2024 Report Posted August 22, 2024 On 8/19/2024 at 8:18 AM, gee-dub said: Even when material comes S2S or better I still run it through the milling steps to assure parts are square and true. Me too. I have been down the dead end road. I will not go there again! Quote
Popular Post gee-dub Posted September 2, 2024 Author Popular Post Report Posted September 2, 2024 I have been out of it for a couple of weeks with my first visitation of COVID. I guess I can cross that one off my list. Symptoms were very mild but long in duration. Be that as it may . . . back to the build. There are a lot of long boards in this build. Despite sapele being available in wide widths I needed a couple of glue ups to get the blanks I require. The sled makes it easy to do these angle cuts of a ganged pair of end panels. Shame on me; I should have swapped that 40 tooth for a 24. I got a little burning . This is a quick fix with the hand plane but changing the blade would have been quicker Stock support is essential for these longer pieces. You can kill all your effort to true things up by letting material dangle at the in and out of an operation. My modified roller stand works well for this kind of varying width stock. A couple of trips through the sander and this glue up is reasonably surfaced. There is a blue tang in a cartoon my grandkids watched back a ways . . ."Finding Nemo". She would sing "just keep swimming, just keep swimming". So . . . Just Keep Milling, Just Keep Milling. Once I am at near finished milling I will layout the tenons. 7 Quote
Popular Post gee-dub Posted September 4, 2024 Author Popular Post Report Posted September 4, 2024 Speaking of stock support; I still managed to mishandle a piece and get a bit of snipe (we don't allow snipe in my shop). Fortunately it was mild and a card scraper took care of it post haste. I need to mill the top groove for the sliding doors. The Bosch edge guide looks like some sort of death-star-defense-unit but is pretty intuitive and works well. I set the depth to "zero" and then work from there. A good check is to swipe a pocket rule over the base plate. Here's the groove I was after. If there's any clean up to be done the ultimate groove / dado clean up tool makes quick work of it. I have had this split piece of sapele around for years. I always knew there would come a time for a rail, or leg, or something that would make use of this naturally split-off section. Today is that day. I swap the 40 tooth blade on the GCS for a 24 tooth for the thicker material. I define a "jointed edge and then cut my blank. It is after 8pm here so I will quit for the day. Ever onward tomorrow! 3 Quote
Popular Post gee-dub Posted September 23, 2024 Author Popular Post Report Posted September 23, 2024 Still taking baby-steps. Here's a shot of knocking the pointy end off of the french cleats. If the points are left too sharp it doesn't take much to get in the way of a good seating of the pairs. For 3/4" cleats I knock off about an 1/8". This is an unusually long set of parts for me. The adjustable tables come into play again to allow me more work surface than I have on my bench or outfeed. When laying out the shop I made a tough decision. I normally do not use 4' x 8' sheets of stuff or other long material and I have a track saw. Therefor I set up my tablesaw with adequate clearance for 5' x 5' BB ply sheets as that is the most common sheet good I use. I stand by my decision as this is the first time in this shop that I think I could have used more infeed at the tablesaw. This rabbet would have been a two pass deal at the tablesaw but I had to rig this Franken-whatever up to make these cuts at an angle. Just a reminder to ALWAYS unplug your machine when you are going to have your pinkies in the cutter area. I was going for the smaller radii. This is where SketchUp helps out. the larger radii turned out to be the right choice. I scratch-mark some of my cutters to make finding the center line easier. The stock is 1" thick so a 1/2" setup block lets me get ready quickly. With the rabbet cut with a spiral and the thumbnail bit using the same fence and featherboard setup I get this profile pretty quickly. Ever onward . . . 7 Quote
Mark J Posted September 24, 2024 Report Posted September 24, 2024 Setting up the router fence diagonally was good thinking. 1 Quote
Popular Post gee-dub Posted September 25, 2024 Author Popular Post Report Posted September 25, 2024 I picked these up at a show back in 2005. They set in a drawer in the drum sander base and only come out now and again. They are one of those inexpensive, silly things that really help out when you need to sand an odd profile. I bought my Domino during a special that included some extra goodies. This little foot helps makes edge mortises more stable and accurate. Finally . . . No great shakes but I am just so happy to be back in the shop. This is where I thought I would be a month ago. Enough sour grapes . . . onward! 6 Quote
Mark J Posted September 26, 2024 Report Posted September 26, 2024 15 hours ago, gee-dub said: picked these up at a show back in 2005. They set in a drawer in the drum sander base and only come out now and again. They are one of those inexpensive, silly things that really help out when you need to sand an odd profile. I like these. If you have a wider cove, wrapping sandpaper around a small clump of yarn also works. 1 1 Quote
Popular Post gee-dub Posted September 29, 2024 Author Popular Post Report Posted September 29, 2024 I was trying to decide how to put this roundover profile on one edge of this trim; router table, hand held router, supporting material, etc. I finally realized the best tool for the job was just a small block plane Just a reminder; having a bit of scrap that is proportionally correct makes setup, testing, and confirmation of your operations a lot easier. Once the trim is ready to be laminated I do a dry run of the glue up. I do dry runs on even the most basic glue ups. I find this ups my success rate considerably. This is one of those times that a lot of snug clamps seem to work better than a few with crushing force. Part of my issue is that I milled parts, got sick, and let them set for a few weeks. Never a good idea. Many small clamping points and the bench as a reference surface will hopefully get me a good result. 6 Quote
Popular Post gee-dub Posted October 4, 2024 Author Popular Post Report Posted October 4, 2024 Interestingly the shooting board turned out to be a good choice for leveling up this trim lamination. A boo-boo made taking about an 1/8"off this part a requirement. I sometimes wonder how I got along without a track saw. The 1-2-3 block is perfect for laying out Domino positions as it lets you mark opposing planes at the same time. I sometimes use the base of the Domino for reference. In these cases you want to be sure your material is well secured to the same reference surface. And if you goof and mark your alignment lines on the wrong side you can just extend them into the area where the tool will stand. In the end all came out well. 6 Quote
Mark J Posted October 5, 2024 Report Posted October 5, 2024 I keep my eye out for 1-2-3 blocks, but I never see them at the hardware or woodworking stores. Are they more of a machinist tool? 2 Quote
wtnhighlander Posted October 5, 2024 Report Posted October 5, 2024 @Mark J, yes, a machinist's tool. I bought an inexpensive set of ten, similar to these, and find all sorts of uses for them. Taylor Tool Works sells a handy hardware kit for bolting these blocks together to make more elaborate fixtures. Note that these inexpensive blocks may not meet the tolerance needed for some machine work, but are more than adequate for woodwork. Also note that the holes in the blocks, threaded or not, aren't sized to allow bolting them directly together, but instead for attaching them to machine tables. That's why the Taylor hardware kit is so useful. 2 Quote
drzaius Posted October 5, 2024 Report Posted October 5, 2024 3 hours ago, Mark J said: I keep my eye out for 1-2-3 blocks, but I never see them at the hardware or woodworking stores. Are they more of a machinist tool? Lee Valley sells them 1 Quote
Popular Post gee-dub Posted October 5, 2024 Author Popular Post Report Posted October 5, 2024 Agree on the budget 1-2-3 blocks being plenty good for woodworking. Those of us who don't do precision metalwork have to remember that the dimensions we find teeny-tiny are just the starting point for precision machine work. . A lot of chores around the house today so only a little progress. Dad was a turner, I am not. When he passed I inherited a lot of cool tools. Some I would never use and I sold those to folks on the forum. This little doo-dad for checking wall thickness has come in handy many times. Obviously in the flat world we can do this calculation with a caliper and some basic math. I just enjoy a tip-of-the-hat to dad when I can read a thickness directly . The reason I need to know this dimension pretty precisely is that there will be some alignment mortise and tenon joints right under the door-slide area. The length of the joint will be glued but, this is the area where we will rest our pillows and heads so I want a belt-and-suspenders function at this joint. I have a constantly thinned collection of scraps and shorts. When I finish a project I look at the scraps I have just created, compare them to what I have and keep the better of each while maintaining a level-set of (probably too much) scrap. I was happy to be able to dig out enough leftovers from the sideboard project to make the back slats for the headboard project. Some of the material is questionable (checks and divots) so I made a little extra. If you are lucky you can place your joinery so as to mill off blemishes or put them to the back or inside and out of sight.. I don't do this for structural pieces (and never for pieces I make for others) but for trim on my own pieces I cheat on occasion. What I don't use will follow the path of natural selection to the burn pile 4 Quote
Popular Post gee-dub Posted October 6, 2024 Author Popular Post Report Posted October 6, 2024 Still bumbling ahead . . . BTW, I am loving these Shop Fox clamps I posted about being on sale a while ago. I use a typical stacked feather board setup to cut this multiple bead profile. For the lap joint I use an FTG rip blade and this tall fence fixture I made many years ago. The original purpose was for drawer lock joints at the router table but it has proven worthy of a lot of other tasks. The back slat blanks go through like so . . . One rabbet on the front and one on the back yields this loose joinery for the back slats. And it ends up looking like so . . . Onward . . . . 6 Quote
Popular Post gee-dub Posted October 13, 2024 Author Popular Post Report Posted October 13, 2024 Just a pic showing the multiple back slats for this frame. As I got to the bottom of my Taylor Tools Domino jars I found a . . . . "Dowel-mino". No . . . Hold on . . . . Forget it . . . I'm patenting that one I realized during dry fit that I was going to need some help to get through the glue up without having a stroke. Turned out that two rectangular pieces of scrap were all that were required. I picked up a Kreg 700 series pocket hole jig during an after Christmas sale or something like that. I felt it was a bit of a splurge given the number of pocket holes I use. The $20 mini has always been my go-to. I have to reassess and say that it makes things really quick when you have a lot of pocket holes to do. It waits in its bin till the next time it is needed. I do the angled router table fence thing again to thumbnail the front edge of the top to the center assembly. I use a spoke shave and a radii scraper to dress things up. Very little goes straight from the machine to the finished product in my shop. I'm happy with this surface. I need to stop saying this but . . . Ever Onward! 5 Quote
Ron Swanson Jr. Posted October 13, 2024 Report Posted October 13, 2024 I always find your attention to detail to be inspiring. This is just beautiful and can't wait until it's done! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.