Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Recommendations for a 5HP cyclone?

Featured Replies

I'm thinking of upgrading my frankenstein 2HP dust collector to a 5HP cyclone.  I'm looking at the Dust Gorilla but it's pretty pricey, and there might be better options out there.  It would need to fit under my shop's 8' ceiling.

I started off with an old 2HP Delta DC that I bought used.  I replaced the filter bag with a Wynn filter, and removed the "air ramp" and built a Thein separator (similar to what April Wilkerson did here).  I suspect that it's acting as a "dust pump" since the corner of my shop with the DC has more fine dust than the other areas of my shop.  Rather than drive myself crazy trying to find and plug the leaks, I'm considering just buying a solution.  Also, I'm continually annoyed by the poor dust collection at my tools, and figure that a dust collector with more oomph couldn't hurt.

Thoughts and recommendations would be welcome.  Thanks

I have also heard good things about the Supercell.  I've also heard that it is loud, and I gotta say that a 5HP DC is going to be very loud.  

  • Author
On 11/19/2024 at 8:29 PM, Mark J said:

I have also heard good things about the Supercell.  I've also heard that it is loud, and I gotta say that a 5HP DC is going to be very loud.  

I wear hearing protection in the shop, and I've given up on keeping things quiet.  So far, the neighbors haven't complained.

The Supercell is interesting.  Higher static pressure but lower CFM.  But, with my ducting, I may actually get better CFM with a system designed to suck air through narrow pipes.  And I'd save almost $1000 and a lot of hassle if I stick with my 4" ducts instead of going up to 6".

I do very occasionally run two 4" tools at the same time.  The docs say that the Supercell can't handle that.  I'm guessing that it's not optimal, but the Supercell Turbo wouldn't catch fire and explode. 

  • Author

Hmmm, there's also the Harvey GYRO AIR G-700.  Less expensive and more quiet.  I seem to recall a couple Youtubers tried it out and eventually went back to more conventional DCs.  I'll have to find out why.

[EDIT] After doing some searching, the main problems with the Harvey is that the bins are smaller and need to be emptied more often, It's got a big footprint (but you can put things on top of it), the inlet at floor level in the front can be annoying depending on your shop layout, and cleaning out the fine dust that gets past the separator can be awkward (again, depending on your shop layout).

I think it might be a win for me in my oddly shaped basement shop.

  • Author
On 11/19/2024 at 10:40 PM, wtnhighlander said:

I've seen a lot of good reviews on tbe Harvey unit also, but pushed it out of mind because the footprint won't work for me. I'll be interested in hearing your experience, if you choose that route.

According to their website, it's $1000 off right now.  No indication of when that might change.  Soooo tempting to make an impulse purchase!

On 11/19/2024 at 10:59 PM, Beechwood Chip said:

According to their website, it's $1000 off right now.  No indication of when that might change.  Soooo tempting to make an impulse purchase!

I think Harvey pricing changes daily, if not hourly.

  • Author
On 11/20/2024 at 9:30 AM, legenddc said:

I think Harvey pricing changes daily, if not hourly.

Crap, I hate being manipulated by marketing, but I may need to hit the "buy" button on this. 

I have a question in to them and I'm waiting for a reply.  I use the iVac system to turn my DC on and off.  With the "computerized" soft start and power levels, I'm concerned that the Gyro can't be controlled this way.  That *might* be a deal breaker for me.

  • Author
On 11/20/2024 at 9:40 AM, Beechwood Chip said:

I have a question in to them and I'm waiting for a reply.  I use the iVAC system to turn my DC on and off.  With the "computerized" soft start and power levels, I'm concerned that the Gyro can't be controlled this way.  That *might* be a deal breaker for me.

iVAC has a gizmo that will learn a DC's remote RF signal to control it.  Their tech support confirms that it works with the Gyro.  I'm going to take several deep breaths before pulling the trigger.

There is a thread over on Sawmill Creek where a couple of members with the G-700 discuss their experiences. The lowdown is that they are good within a fairly narrow set of parameters. It definitely is not a replacement for a 5HP collector. I'd read up thoroughly before buying.

  • Author
On 11/20/2024 at 3:36 PM, drzaius said:

There is a thread over on Sawmill Creek where a couple of members with the G-700 discuss their experiences. The lowdown is that they are good within a fairly narrow set of parameters. It definitely is not a replacement for a 5HP collector. I'd read up thoroughly before buying.

Thanks, but too late.  I will read up though.  If it's bad enough, I may eat the cancellation charge.

  • Popular Post
On 11/20/2024 at 9:14 AM, Mark J said:

Doesn't @JohnG run a Harvey DC?

I do have one, and I have been happy with it. I bought it because it's unique form factor works well in my shop. 

I have not used it with my lunchbox planer much. I don't use the planer too often, and when I do I often take it outside and let the chips fly (I have a basement shop, and while most tool sounds don't carry through the house too well, lunchbox planer noise is something special). For my table saw, bandsaws, 6" jointer, and drum sander, it works well. My main DC run is only about 20' or so of 4" PVC but has a few turns in it. I do also occasionally run a 20' 2.5" flex line to my oscillating sander and for general cleanup. I have blast gates at most machines and I'm a solo shop, so only one machine running at a time.

I upgraded from a 2hp Harbor Freight DC with Wynn filter. I noticed a big improvement when I got the G700. But I don't know if it's fair to compare it with a 5hp Dust Gorilla. I have no idea how it would compare to a typical 3hp cyclone. Or how well it will perform in a bigger shop with longer runs.

I bought the G700 at a similar price to the current sale price, and I would personally buy it again at the same price. As I've mentioned many times, Harvey price fluctuations are ridiculous. Please nobody buy anything at their "list price." 

  • Popular Post

I have been happy with my Onieda Dust Gorilla no issues in 15+ years

  • 2 weeks later...
  • Author
  • Popular Post

Just installed my new Harvey G-700.  Taking a break before doing the ducting and hooking up the tools.

One surprise: the installation instructions say that it should be 18" away from the wall for heat dissipation.  It didn't say which side should be 18" away from the wall.  Either way, that makes an already large footprint even larger.

It was a job to get it off the pallet and down the hall into my shop.  But, I'll only have to do that once.

Only the front (side with the intake and dust bin door) of mine has 18” clearance. I think that will only really make a difference in a commercial shop running all day long every day. 

  • Author
On 12/3/2024 at 4:45 PM, JohnG said:

Only the front (side with the intake and dust bin door) of mine has 18” clearance. I think that will only really make a difference in a commercial shop running all day long every day. 

Mine has empty space on the front and right, several inches on the back, and about 2" on the left side.  I figured I'd be fine since I don't run it continuously and my shop never gets very warm.

Thanks for the confirmation.

  • 1 month later...
  • Author
  • Popular Post

Wanted to follow up now that I've had a chance to use the Harvey G-700.  So far, I've been very happy with it.  I thought that the 5 second start up time would be a problem, but the thing is that it's 5 seconds to come to full power, and it doesn't need full power to be effective.  So, I turn on the tool (which turns on the Harvey) and then reposition my hands to make the cut, pause a fraction of a second to make sure everything is lined up right, and start making the cut.  So I start the cut at 2.5 seconds (half power and rising) and that's fine.  And that's if I'm rushing.  If I'm relaxed or careful, then the Harvey is at close to full power when I start the cut.   Bottom line, I don't even think about the start up time, I just work the same way I always have.

I haven't really noticed if it's quieter than my old 2HP Jet, but I'm wearing hearing protection and I've got tools and my air cleaners going so that's not a big deal.

So, almost 2 months later, and I've got no buyer's remorse. 

 

 

On 1/30/2025 at 7:40 AM, Beechwood Chip said:

So, almost 2 months later, and I've got no buyer's remorse.

That's good to hear.  I have looked at the Harveys occasionally but my present DC is treating me well so no rush.

  • Author
  • Popular Post

I will say that before you buy a Harvey Gyro, think very carefully about where it will go in your shop.  I can't run my DC duct on my ceiling, so it has to run along the bottom of the wall.  And I happened to have a convenient corner that would fit the G-700.  So, in my shop, it fit right in and actually gave me some additional usable space.  But, in many shops, taking up twice the floor space and half the height won't be a win.

In addition to that overhead ducting allows for more direct routing which keeps efficiency up. You just have to plan around that. Definatly won't work in some shops through, like mine.

  • Popular Post

Folks looking at the G-700 may want to check the used market.  I have seen three in the last 6 months for sale on various forums.  Could be good way to save a few bucks if the sellers happen to be near you.

  • Author
On 2/1/2025 at 1:45 PM, gee-dub said:

Folks looking at the G-700 may want to check the used market.  I have seen three in the last 6 months for sale on various forums.  Could be good way to save a few bucks if the sellers happen to be near you.

Makes sense!  When I was researching it I found several Youtubers who posted videos about getting the G-700, and then posted videos explaining why they were getting rid of it.  All of them said that it worked great, but didn't fit in their shop.  All of those G-700s must have gone somewhere!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.