Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Do you have a limit on scrap?

Featured Replies

I spent the weekend trying to clean up the garage/shop.  My biggest obstacle is all the offcuts and small pieces, that "I may need some day".  How do you draw the line on what to keep and what to discard? Over the past several months, I have leaned towards throwing it all away, or in the firewood pile, then the time comes and I need a 1x3x 3/4 piece of whatever and I find it, completley negating my thinking.   Where do you draw the line?

The weather is warming up, so i fill up a bin for the fire pit. That helps with the overwhelming pile of scraps. Unless you have offcuts of special wood that you plan to use for small trim pieces such as pulls etc, i dont keep too much bc it adds up too fast depending on your workflow.

Its all about the flow for me. If i am doing a bunch of plywood work, the plywood scraps get thinned out. I try to keep only pieces half the size of the smallest piece of the project..

Good point spencer, I forgot to mention plywood. I have been working exclusively with plywood lately due to the task at hand. Plywood never makes it to the fire pit, with glues and all. I have yet to build a lumber rack and cutoff storage. But I have 2 cardboard boxes which are roughly 1x1 and 2 feet high. I throw pieces in there I wish to keep. Sometimes a piece of mdf ends up in there, and I cant seem to figure out why. This box fills up with walnut, cherry, mahogany and maple. Things like pine and red oak that I have to use often for work rarely make it into the keeper box. I save longer pieces for future shop use, smaller pieces go to fire. I also have a overhead storage area that is packed with all the boxes my tools come in. WHY DO I STILL HAVE THESE!!! 

I do keep some bits until I have finished a project just in case I mess up and have to put a matching piece to correct the error. Then I put the smaller bits in the burn box. Cut off ply or cut offs from ends of tops usually go straight in the burn box.

About a month ago i had one of the most pricy bonfires ive ever had. I had to do something. I still have some but i would say its a more managable collection now. Im sure I will at some point say why did I burn that stuff but for the sake of organization i had to.

I throw it in a big garbage can, cover it with planer shavings, and forget about it until I light the fire.

In a fire pit, of course. Excluding the can.

The more expensive the wood the smaller a scrap I save. Thicker stock scraps get saved smaller than 3/4 stock does, good for blocking and fillers etc. I have a box of 5/4 and 8/4 poplar scrap that is great for jigs, spacers and such.

If I am working in almost any wood I save every scrap for set ups, test cuts, spacers, finish samples and such untill the project is done. Too many times this habit has saved me . Then only the bigger more useful pieces are kept, trash the rest.

I made a scrap bin out of some scrap OSB and toss stuff in there which piles up quickly. Every few months, I check the inventory and force myself to toss out stuff despite that nagging "I'll use it someday" feeling in my head. Although the stuff does occasionally work perfect for jigs and definitely sacrificial backing boards, about 95% of the time scrap pieces always manage to be just a little undersized for what I might need them for at the moment.

 

Exotics are the only thing I keep hanging on to, they can be useful for accents or decoration, not to mention expensive to throw out.

 I burn them at the end of the day. If they wont fit across the span of my lumber rack about 4ft they go into the burn pile. If they are short and look real nice they go into the shed for my grandson.

When I started I had no money and every dollar I made selling my work went back into buying materials for the next thing to make and anything left over was saved for tools.  So every little scrap of wood was precious to me.  I don't have to do that anymore, and yet I have this wall of scrap.  I worked on cleaning it out yesterday and got down to the bottom of some of it, you know where the "good stuff" must have been and I just couldn't get to it with all the other stuff on top.  The stuff underneath was even worse.  There comes a point where, yes you might have been able to make that little thing out of scrap, but it takes more effort to find the right piece of scrap than it does to cut it off the end of a board you can just take out of the rack.

I save anything about 2 inches wide and over 12 inches long. Anything else gets split into kindling for the wood stove.

Doesn't apply for certain exotics but I attempt to follow my mentors urging. If I haven't used it in a year of saving it then it goes.

Soft hardwood drops, like poplar, cypress, and basswood, get cut into shims and wedges for use in installations. Plywood depends. Any 1/4" ply that's big enough for a drawer bottom will get saved. Any 1/2" big enough for a drawer side gets saved and any 3/4" big enough for a standard cabinet shelf gets saved. That being said, you can only use so many wedges, shims, and other "future parts" before you run out of room. That's when I do a radical clean out and it all goes on the burn pile.

I guess it all depends on what you build. I save and high-grade all of my hardwood scraps to cut them down into smaller little crafty projects. building blocks don't have to be too big, and you also don't need to purchase any wood for the project. I've also got a jenga type set in mind, and those blocks are little!

 

Small bits (less than 4"x4") of pine and plywood go directly to trash.

I actually keep primary woods at 3/4 x 6" x 16" (and over) and secondary wood are 3/4 x 6" x 24" or over in a set of bins (total storage is about 250bf for scratch stock).  When the bins get full (say quarterly), I cull through and trash the pieces that are more than about six months old -- that reduces the scrap pile by about 50%.  So it's kind of like a quarterly rolling scrap stock where the best 'floats-to-the-top'. 

 

Another criteria -- I start looking at shop-made Xmas presents around Sept.  I try to pick something small that lends itself to batch processing... I start a separate scrap bin for 'xMas stock', then trash everything after Jan 1...

 

Yet another criteria -- If I have some nice straight-grained hardwood left over, I see if I can make some clamping cauls.  I find that I can never have enough of the things...

 

Further criteria -- I typically mill moldings from 7/8 stock... So any rips from long stock at finished 7/8 (or better) with straight grain gets saved...  Since these are typically long narrow (usually 2" or less) stock, I save them in a separate bin to prevent dings...  The next time I setup to mill moldings, I pull all the 'scrap' and mill everything and store the finished moldings for final use...

 

 

==> The more expensive the wood the smaller a scrap I save. Thicker stock scraps get saved smaller than 3/4 stock does, good for blocking and fillers etc.

 

+1 -- I keep ebony, tulip, etc down to 'peg/drawer-pull/wedge'-sized.

 

 

==> I have a box of 5/4 and 8/4 poplar scrap that is great for jigs, spacers and such.

 

+1 -- I keep 'jig' sized poplar, MDF and BB-ply.  But I usually only stock 1/2 or 3/4 stock -- I try to standardize most of my jigs to that size stock.  I also save 'fence'-type stock -- say 8/4 x 3" x 24".

 

 

==> If I am working in almost any wood I save every scrap for set ups, test cuts, spacers, finish samples and such untill the project is done.

 

+2 -- If I plan a new finish schedule, I actually mill-up a separate 'finish setup' stick and keep every size that can take a reasonable amount of finish.... When the project is done, it all goes in the trash...  Sometimes I keep a 'final finish' sample and write the finish schedule on the back...

 

 

Since I try to get everything off the wide-belt at 3/4, I keep some 3/4 off the WB around for the next project for setups...

I've been making porch swings lately and I have a pile of scrap pine that is becoming dangerous.  Looks like a good weekend for the fire pit.

I don't have any "scrap", it's all part of my wood collection. ;-)

Pine, poplar and ply toss anything smaller than 4x4 any thickness. I build bird house ornaments, so I keep exotics down to perch size!

BRuce

Like TripleH, I hang on to mine for use at Christmas time. 

 

I have a few boxes that I use for different species.  The boxes are pretty good size so, if they get full I usually keep the best and burn the rest.  The fullest boxes determine what the Christmas gifts are made from.

 

I also have a couple friends that like to turn pens.  I certainly donate a bunch of scrap to their cause.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.