Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

What? Surface plane MDF?

Featured Replies

I was reading an article the other day in a magazine and it suggested to plane MDF down to the appropriate size for a 0 clearance insert.

My knee-jerk reaction is "Not in my planer!!!"

Is there something I am missing here? Seems like a terrible idea to me.

I think I read the same article, as a newb, my first thought was, "oh, you can do that?" assuming this particular magazine wouldn't steer me wrong.

Curious to see what everyone else thinks.

When I have reduced MDF in thickness it has thrown the balance and it usually bends. You loose the nice hard surface too. Not to mention dust and all the abrasion on the tools. There must be better options! 

I always use plywood as zero clearance insert on tablesaw. I should have thought planing mdf would fill the air with horribleness even with the dust extractor on. What mag suggested that Pug?

No ZCI needs to have a complete thickness adjustment. Most ride on very narrow tangs or a ledge around the outer edge. A quick pass at a router station would be preferable in my opinion. This can utilize carbide bits that hold up much better cutting MDF.

==> Run it through the drum sander and flip it every pass.

+1

 

Just make sure your DC is working well... I can imagine this making an unholy mess...

  • Author

I always use plywood as zero clearance insert on tablesaw. I should have thought planing mdf would fill the air with horribleness even with the dust extractor on. What mag suggested that Pug?

I typically use ply or laminate floor scraps. Whatever is close to final dimension, and then shim it with blue tape (or reduce it with a router, as was mentioned).

The magazine was the newest issue of FWW, on page 50.

Is there something I am missing here? Seems like a terrible idea to me.

 

Nope, it's just a terrible idea.  I once took a jack plane to some MDF even that made a godawful mess, of the shop and the workpiece!  I can't imagine sending that stuff through a thicknesser.

 

As C Schaffer points out, table saw throat inserts sit on a small ledge around the opening.  I make my ZCI's out of anything at hand, so long as it's thin enough to sit below the table when resting on that ledge.  Once I have it sized to the opening, I put four short screws at the corners and use those to bring it up and get it perfectly leveled to the table.

I just replace the insert on my throat plate. I have 2 aluminum throat plates that have a dovetailed slot cut in them. A 1/4 " Baltic birch piece slides in.

MDF wiill never get near my planer.

 

For ZCIs, I do what Rob does except I use 1/4" Allen set screws.  I drill pilot holes and then tap threads all the way through so the adjustments can be made from the top without removing the plate.  I prefer to use ply because it takes a beating a little better than MDF.

when i bought my saw used, it had so much crap piled on it that i couldn't see what the insert situation was. after several hours of moving the crap, i saw that he had modified the original aluminum one with bondo to get a sweet zero clearance. he quickly removed it, and the forrest blade in there and brought back a very well used shop made insert. baltic birch with laminate on top and phillips wood screws for the leveling. :/

 

i just buy those ones from lee craft... maybe i will join the cool kids club one day & make my own. 

 

what about planing HDF? i wonder if that would hold up better or be even worse for the planer.... 

No ZCI needs to have a complete thickness adjustment. Most ride on very narrow tangs or a ledge around the outer edge. A quick pass at a router station would be preferable in my opinion. This can utilize carbide bits that hold up much better cutting MDF.

 

+1

MDF isn't really strong enough to make a good insert anyway, unless you maybe used 3/4" and like others said just route out where the ledges are.  I made a dado insert out of 1/2" MDF and had to add hardwood strips underneath on both sides to keep it from flexing.  I keep using it, but I made them out of 12mm Baltic birch from them on.  They do shrink in thickness in the winter and I have to shim them up with self adhesive paper to keep them flush with the table.

I'm guessing there will be a lot of 'letters to the editor' on this. It will be interesting to see the author's response.

Dont put MDF in a planer.  It will dull your blades so fast. 

 

I read a planer review a while back and they put a piece of MDF through them to simulate somthing like a 1000 linear feet of planing. 

==> I was reading an article the other day in a magazine and it suggested to plane MDF

 

What magazine?  The more I think about this, the more ridiculous it sounds...  I just hope it's not a mag that I pay a subscription...

 

 

I think about the only way to do this would be a wide-belt or drum sander -- but even so, the integrity of MDF will be compromised when the outer layers are gone...

 

It's a bad idea no matter how you look at it...

  • Author

==> I was reading an article the other day in a magazine and it suggested to plane MDF

 

What magazine?  The more I think about this, the more ridiculous it sounds...  I just hope it's not a mag that I pay a subscription...

 

 

I think about the only way to do this would be a wide-belt or drum sander -- but even so, the integrity of MDF will be compromised when the outer layers are gone...

 

It's a bad idea no matter how you look at it...

Newest issue of fine wood working. It's in the section about creating a zero clearance insert for a mitre saw.

Here is the exact quote from the magazine:

"You might have to plane the MDF to make it flush with the base"
 
They are not specific as to which tool/machine would be best for this operation.  Honestly when I read it my mind automatically translated "plane" into "sand".  I would not put a piece that small through a thickness planer, even if it were solid material.  

==> Run it through the drum sander and flip it every pass.

+1

 

Just make sure your DC is working well... I can imagine this making an unholy mess...

 

This works great.

 

This is how I set my sander parallel...   Stripe an MDF sheet with a fat pencil, and adjust as the sheet slowly feeds.

 

I'm also in the camp of start thinner, and add set screws to adjust up.   1/4" set screws are available everywhere, even big boxes...  Drill and appropriate hole, tap with a 1/4-20 tap (also cheap and easy to find).  Dribble thin CA glue into the threaded holes to harden them, if desired.  Let the glue dry completely and install the set screws.

==> This works great.

==> This is how I set my sander parallel...   Stripe an MDF sheet with a fat pencil, and adjust as the sheet slowly feeds.

 

Yea, but you goal is to adjust a sander, not surface the MDF to make something usable...  Next time I get some MDF scrap, I'm tempted to run it through the wide-belt just to see what I'm left with -- talk about a test of the shop's DC...

 

 

 

==> I'm also in the camp of start thinner, and add set screws to adjust up.   1/4" set screws are available everywhere, even big boxes...  Drill and appropriate hole, tap with a 1/4-20 tap (also cheap and easy to find).  Dribble thin CA glue into the threaded holes to harden them, if desired.  Let the glue dry completely and install the set screws.

 

Exactly what I do, but I use Epoxy...  Same difference...

This got me thinking...  

 

We shape MDF with routers, etc... and it works very well.   Mountains of MDF molding is sold daily.  I've even made stile and rail raised panel doors of 100% MDF.   I do understand all these are created with carbide blades, not the HSS installed in most planers. Don't forget, I'm a guy who edge planes batches of 1/4" baltic birch ply for sled and jig runners. 

 

Since I'm due to swap out my DW733 planer blades for a sharp set, I don't have a ton to lose. 

 

I volunteer to try it and report back!   :rolleyes:    More to follow...

Good luck!  Will be interested to hear how it goes!

http://forum.canadianwoodworking.com/showthread.php?34876-Thickness-Planing-MDF-my-own-little-moment-of-discovery

If these guys can be trusted (because they are strangers, not because they may be Canadian) you can save yourself a little knife wear.

 

Makes sense to me, so I'm going to try it anyway.   'Cause I can! 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.