Recommended Posts

Posted

The hammer B3 comfort winner looks to be my choice , now I just need to convince the wife I need a saw that costs 190.000Kc (czech krone).

I've also ordered the mortice attachment for the A3 31 p/t and the wheel kit for the FB600 bandsaw

Posted
5 hours ago, wdwerker said:

That's $8975 US today. Serious machine for a small shop. 

i know:o, i'll just say it real quick when i tell her indoors.

Posted

Honestly I am not too impressed with the quality of Hammer. I have their Jointer Planer and wish I had paid extra for the Minimax or Felder lines. The quality of hte machine overall just isnt there for what is paid IMO. I would go with a sawstop or powermatic over the Hammer unless you really wanted a slider. 

Posted
44 minutes ago, Cygnus A said:

Honestly I am not too impressed with the quality of Hammer. I have their Jointer Planer and wish I had paid extra for the Minimax or Felder lines. The quality of hte machine overall just isnt there for what is paid IMO. I would go with a sawstop or powermatic over the Hammer unless you really wanted a slider. 

Which Hammer A3 do you have?

Posted
1 hour ago, ben_r_ said:

Which Hammer A3 do you have?

A3-41. I have various complaints about it but it does what it is supposed to. It seesm Hammer cuts corners to save cost but sometimes the choices the make are questionable. I don't trust the fence design to remain square to the table for example and that is kind of a big deal in a jointer.

Posted
27 minutes ago, Cygnus A said:

A3-41. I have various complaints about it but it does what it is supposed to. It seesm Hammer cuts corners to save cost but sometimes the choices the make are questionable. I don't trust the fence design to remain square to the table for example and that is kind of a big deal in a jointer.

Maybe I just got lucky, because I've seen this complaint from several sources, including Matt's excellent review. Or maybe it's just because I don't tilt my fence for bevel work - I use my table saw. My A3-41 fence was so close to square out of the box that I only needed a tweak on the outfeed side of the bracket to bring it into square. 5 minutes of adjustment and it's stayed square after numerous removals and reinstallations. 

I have a friend who has the A3-31 and he said he spent hours getting it into alignment the first time. I suspect that the real problem all along was that his front rail was out of parallel to the table.

I've been thrilled with mine.

Posted

in the end i've ordered the K3 COMFORT WINNER as i can have it here sooner and i also have my name on a hammer spindle moulder that's going to be displayed at an expo at the end of february. the sales rep has told me it will come with all the extras and free delivery and set up :).

i've had my A3 31 a few years now and the only thing i've changed are the blades , runs like a dream.

Posted

Congrats on the saw! Any particular reason why you went with separates instead of saving $2ish grand on a combo? Everyone pushes separates if you have the room, but the cost savings were too enticing for me to pass on. 

Posted

I have the Hammer K3 Winner with the 49" slider. I purchase it a few months ago in preference to a Saw Stop. I am very happy with my decision. The K3 is a different beast to the SS. It does require you tomrethink how you use a tablesaw, but once this gets through, you would not consider a traditional type tablesaw again.

The build quality is excellent. I have had a N4400 bandsaw for about 7 years and a A3-31 combo for 3 years. They are substantial machines that deliver.

11a.jpg

Regards from Perth

Derek

 

  • Like 2
Posted
1 hour ago, Pwk5017 said:

Congrats on the saw! Any particular reason why you went with separates instead of saving $2ish grand on a combo? Everyone pushes separates if you have the room, but the cost savings were too enticing for me to pass on. 

thanks PWK,

i have a large workshop which is a plus, also i would like to have dedicated machines so on that odd time when i have two people working in the shop we can just get on with what needs doing.

Posted
On 1/5/2018 at 8:03 PM, Mick S said:

Maybe I just got lucky, because I've seen this complaint from several sources, including Matt's excellent review. Or maybe it's just because I don't tilt my fence for bevel work - I use my table saw. My A3-41 fence was so close to square out of the box that I only needed a tweak on the outfeed side of the bracket to bring it into square. 5 minutes of adjustment and it's stayed square after numerous removals and reinstallations. 

I have a friend who has the A3-31 and he said he spent hours getting it into alignment the first time. I suspect that the real problem all along was that his front rail was out of parallel to the table.

I've been thrilled with mine.

I don't think it's about tilting the fence for bevels being an issue, I think it's just a weakness of the fence system in general. It seems like a few of us have had this issue. I personally got frustrated with Hammer tech support as I work nights and the hours I can talk to them are when I sleep and it's a lot of voicemail phone tag. It also never seemed that they could not figure out the issue trying to pretend as if the fence was not known to be an issue. I can use mine reliably now for edge jointing only if the fence is set within four inches of the front. Anywhere else and it will start slipping from 90. I like a lot about the machine but hate that fence after days of screwing with it. Only tool to ever give me hell.

 

Personally I'd buy a SawStop again any day of the week or else I'd buy a powermatic if that wasn't a feature I wanted. Hammer / Felder sales reps are great, haven't been impressed enough with tech support.

Posted

I will second the Frits and franz jig as one of the first things you make. Traditional ripping on a slider is very awkward. The jig lets you rip off the wagon. It also acts as a safe way to cut small parts and a tapering jig. I didn't make one until a couple weeks ago and that was a mistake. The carriage support on a 80"+ sliding table is exactly where you want to stand when ripping traditionally. I kept my unisaw and I don't plan on ripping or dadoing much with my slider, but the FF jig is still worth making. Derek's is one of the pricier versions I've seen, but they can be as simple as two pieces of plywood with a a handle on the one. I made mine with the inexpensive incra t track with tape and woodpecker jig knobs for my homemade stops. Cost me about $30 and an hour to make. 

 

Two people are are a good reason to have separates! Let me know what tooling you get for the shaper. I haven't purchased anything yet. Get ready for some sticker shock when it comes to equipping the shaper. The cutter heads are expensive and I've yet to pick a feeder. 

  • Like 1
  • 1 month later...
Posted

Nice, thats a great looking bandsaw too! I cant read the number, but is it the 20" or 24" model? Did you get a blade guard with the machine?

 

Seriously, make the F&F jig immediately. I waited a month or two and complained about the effectiveness of the machine the whole time. 

  • Like 1
Posted

The bandsaw is a FB600, with 24" wheels, I do have the blade guard but the blades won't be here until tomorrow.

I will put an order in for the incra F&F jig set up soon or I might jump on the coach to Berlin to get them.(only incra dealer near me).

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 36 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined