Recommended Posts

Posted

I am a do some minor home renovations and need some advice on what is a good affordable braid/nail gun. I will use for everything from putting trim back on after painting to tacking stuff together before screwing etc.

I have looked at pin nailers and unsure what purpose they are used for and what the limitations are, or is a 18g just a good all round  product to get?

My budget is under $100 as I will not use it a lot so can't justify spending $100+

 

Thanks

Jason

Posted

18 ga is a little small for most home trim; baseboard, casings etc. By the time the nail goes through 3/4" of trim & 1/2" of drywall you'll need at least a 2" nail. I found that 15 or 16 ga holds much better & will actually suck the trim tight whereas the 18 ga absolutely will not.

Posted

For most residential applications 18 gauge is fine. For most mdf trim it has plenty of bite, especially since the moldings will be latexed. 18 gauge is also preferable as the nail holes are much easier to fill. The only reason we use 15 or 16 gauge is staircases or a big heavy hardwood molding that would require a bigger gauge.

So get an 18 gauge, you will be good to go.

Sent from my SM-P550 using Tapatalk

  • Like 1
Posted

I have hitachi, senco and paslode. For the price the paslode f18-200 is hard to beat. Ive installed thousands of feet of moldings with this model without any problems. If you want cordless goes with the new senco fusion 18 gauge. I have one and it seems to work much better than the paslode cordless stuff I have used in the past.

Sent from my SM-P550 using Tapatalk

Posted

I have two senco.  one is over 20 years old and not a single problem.  One thing that steered me toward seance years ago is they are designed to let the user do repairs to them if need be.  Simply purchase the small kit of replacement parts and DIY

Posted

I have the Hitachi and the Senco and find myself going to the Hitachi most times.  They run about 100 bucks.  I'm on my second one in 25 years and that's only because I dropped the first one off of a tall ladder onto a concrete floor.  Hard to go wrong with either one tho.

Posted

I bought a 16ga Rigid recently, used it to hang my pre-hung bathroom door.  Also used it to nail my vanity together and install the door and base trim.  The nail heads are a bit big for some stuff, but I figured the wider range of nail length would be better for my use overall. 

 

I could see myself adding a 18ga nailer someday though for tacking smaller projects together.

Posted
2 hours ago, shaneymack said:

For most residential applications 18 gauge is fine. For most mdf trim it has plenty of bite, especially since the moldings will be latexed. 18 gauge is also preferable as the nail holes are much easier to fill. The only reason we use 15 or 16 gauge is staircases or a big heavy hardwood molding that would require a bigger gauge.

So get an 18 gauge, you will be good to go.

Sent from my SM-P550 using Tapatalk

No one uses 18 here except in trim that might split with 16. Maybe it is a local industry thing but casing is always shot with 16 and shoes etc with 18. 

Posted

For most residential applications 18 gauge is fine. For most mdf trim it has plenty of bite, especially since the moldings will be latexed. 18 gauge is also preferable as the nail holes are much easier to fill. The only reason we use 15 or 16 gauge is staircases or a big heavy hardwood molding that would require a bigger gauge.

So get an 18 gauge, you will be good to go.

Sent from my SM-P550 using Tapatalk

No one uses 18 here except in trim that might split with 16. Maybe it is a local industry thing but casing is always shot with 16 and shoes etc with 18. 

Interesting. Yeah probably a location thing. I've had no issues quality wise with the 18 gauge. Even all interior hollow core doors here are installed with nothing but 18 gauge nails, no shims, no screws. Of course i am talking all mdf trim which every joint ends up being latexed, which is actually stronger than the nails.

Sent from my SGH-I337M using Tapatalk

Posted

I have a 18ga Dewalt which doesn't require an air compressor:

Bare tool: http://www.amazon.com/gp/product/B003J5KT6I?psc=1&redirect=true&ref_=oh_aui_search_detailpage

Kit: http://www.amazon.com/DEWALT-DC608K-18-Volt-18-Gauge-2-Inch/dp/B0011Z5ZNU/ref=pd_sim_469_5?ie=UTF8&dpID=51vcJQvBVwL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=1V0AE57Y7QM15VP8SDAX

I use it for small projects and works fine for brads up to 2''. This nailer will sink a brad in a brick, no problem.

Posted
19 hours ago, Daniel. said:

 This nailer will sink a brad in a brick, no problem.

Have you tried this? If so,  do it again, and take pics.  I'm not doing it to mine but am happy to let you.  * )

Posted
19 hours ago, Daniel. said:

I have a 18ga Dewalt which doesn't require an air compressor:

Bare tool: http://www.amazon.com/gp/product/B003J5KT6I?psc=1&redirect=true&ref_=oh_aui_search_detailpage

Kit: http://www.amazon.com/DEWALT-DC608K-18-Volt-18-Gauge-2-Inch/dp/B0011Z5ZNU/ref=pd_sim_469_5?ie=UTF8&dpID=51vcJQvBVwL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=1V0AE57Y7QM15VP8SDAX

I use it for small projects and works fine for brads up to 2''. This nailer will sink a brad in a brick, no problem.

I'm waiting for them to make a 20v. All my batteries are 20v and I'm not going back in time for 1 nailer. I don't know what they are waiting for...they already have a 20v framing nailer.

  • Like 1
Posted
1 minute ago, Janello said:

I'm waiting for them to make a 20v. All my batteries are 20v and I'm not going back in time for 1 nailer. I don't know what they are waiting for...they already have a 20v framing nailer.

I bought the 18v bare tool version because I have plenty of 18v batteries.

  • Like 1
Posted

If you live near a harbor freight store it's worth looking at one of their central pneumatic brad nailers.  It's not uncommon to see them for $25.  I don't use a brad nailer very often so this is what I use and I've had no problems with it outside of the little rubber tip falling off of the safety bar.  Nothing a little duct tape didn't fix.  I have no experience with their compressors so I can't vouch for how well they hold up but the 3 gal oil-less pancake model was selling for about $40 this past week.

I've never used the battery powered guns but if I were looking at buying one I would let whatever battery system I'm invested in make the decision for me.

Posted

I have all 3 typical nailers - 16, 18, and 23.

Like Shane, all trim I install is with an 18g nailer.  I have installed a lot of mdf casing, baseboard, quarter round, and jambs with it.

The 16g I use rarely.  I use it to nail up quick mdf jigs or the occasional mdf project.

The 23 is a Pinner, used to hold small parts while glue dries.  I use it mostly on cabinet doors (pin the stub tenon) so I can resume using the clamps.

All 3 of my guns are ridgid air hose.  I have no complaints - they have served me very well, and continue to do so.

Posted

I have a Grex 23 gauge pin gun that shoots up to 2" nails. I use it to hang high end trim on installs . I use a tiny bead of glue and the nails hold in till the glue dries. Holes are almost invisible . But the gun alone probably cost more than a complete kits I have seen advertised.

18 gauge  and a little caulk should do fine for MDF trim.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 56 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined