Recommended Posts

Posted

A few months ago I gave in to temptation and bought a TS55 and an MFT.   Absolutely love them.

My 10 year old Ridgid Contractor saw is up for replacement.  I was looking at Grizzly offering, but got to thinking - Do I need a new saw or can I make the Festool my TS replacement with add on like the Parallel Guide and a second table?  It would reduce dust and save space as well in my small shop.

  • Like 1
Posted

I agree with wtnhighlander, depends on your needs. I have very few needs for tool portability - I mainly make furniture in my shop. I have both the TS55 and a cabinet saw. I use the TS55 for large sheets too big for me to comfortably handle on the cabinet saw and a few odds and ends things, but use the cabinet saw all the time. 

Posted

Yep.  I love my my TS55, and it's especially awesome with an MFT added.  But it does not take the place of a good table saw, especially after you add a nice sled.  Ripping narrow stock with the TS?  Nope.  Small parts?  Dadoes?  Nope.

I hear people try to make the argument all the time that a track saw can replace a table saw, and they always end up sounding stupid.

Posted
8 minutes ago, Eric. said:

I hear people try to make the argument all the time that a track saw can replace a table saw, and they always end up sounding stupid.

Sounding stupid never stopped anyone before!

Hell, I say go for it! Get the tracksaw and MFT as a full-time tablesaw replacement. Make sure you get the festool router so that can run on the track for your dadoes. I think Seneca makes something to help you out with with ripping... Small parts, meh... Cut those by hand and finish up with hand tools.

All in all, you won't save a dime. You may prove a few people wrong, but it'll cost ya.

Posted

I have a Festool Track Saw, and as a contractor I have limited space to haul around my equipment in the van. One thing I looked at was dumping the table saw and just using the track saw.

But as I studied what I cut on the job sites and considered, "Could I do this with all Festool and no table saw?" it seemed like an unrealistic idea for the very reasons Eric mentioned. 

Posted

Cutting multiple small parts on the TS55 is going to be difficult. So easy on a tablesaw. Both have advantages but neither can do it all. I would not try to build furniture without a tablesaw. 

Getting a tracksaw was a game changer after 35 years of using a circular saw and a straightedge. Ripping a quality straight edge on a long board is great but the cost of that long track was quite high.

Posted

I say do what you want. Nobody need a table saw. If they did, there wouldn't be pure hand tool woodworkers. Most people would tell you "no way." Why? Cause the table saw a huge part of their workflow. Like, I can't imagine going to work without my car. Because I live 50 miles from work and there is no public transportation and uh.. that's how I get there. Doesn't mean that every clownshoe needs a car though. Their needs may differ.

Posted

Go with the table saw! Festool is overrated and overpriced! I can this because I used to have a pretty big Festool inventory. When I found out I was having another kid and moving to HI I got rid of all of my big machines and all of my Festool Stuff. When I first got into Festool I had just a TS-75, MFT, bandsaw and no table saw. This was a frustrating setup and many times I wished I had went with a table saw instead of the TS-75 and MFT. 

I know you already have a TS and MFT but you will miss having a table saw. I do almost all my work with hand tools now but bought a portable table saw for those few times I need to make several small cuts. 

For the record I am not a Festool hater now, I just don't think they are worth cost when deciding between Festool and xxx.

Posted

I'll be the contrarian and say you can get by without a table saw. However, you'll need a router, router table and bandsaw to do so, which most here do. You can use third-party parallel guides to make small cuts, or use the bandsaw, which is safer than the table saw. Use a hand plane to skim off the blade marks and you're set.

Posted

Both are indispensable to a pro. Breaking down sheet goods by yourself on a jobsite? Yeah you'll be dying for a track saw. Ripping small trim pieces, no fun without a table saw. #fact

Posted

Ok, can any of you in the Festool club tell me how to make raised panels or coved / curved moldings with only a tracksaw and bandsaw? I've often wondered about this, maybe it IS possible to ditch the table saw.

Posted

I've seen guys build nice stuff with some lots of different tools and techniques, so I don't think any tool is a "requirement". There are usually at least a half dozen ways to do just about any operation.

That being said, there are A LOT of things I use my table saw for, and I wouldn't trade it for any other tool

Posted
15 hours ago, wtnhighlander said:

Ok, can any of you in the Festool club tell me how to make raised panels or coved / curved moldings with only a tracksaw and bandsaw? I've often wondered about this, maybe it IS possible to ditch the table saw.

I think this would be a case of the appropriate tool for the job. If you're a pro you'd definitely know the best and most efficient way to produce your work, which would mean either a router table or table saw, as far as I know.

I'm just a beginning hobbyist so I don't claim to know much. I do know there are ways around a table saw if one chooses to go without. I also know that a table saw may indeed be the best tool for certain jobs. However, hobbyists have more leeway than pros, I believe. 

Posted

I will throw in my 2 cents.  I have only been woodworking for a little over a year,  Started after I retired.  I have a Festool tracksaw and love it and considered getting rid of my table saw (which wasn't a bad one, a Delta 36-725) but I ended up buying a Grizzly 1023 cabinet type saw fairly recently.  Now it is not the greatest cabinet saw, but it has really made it much easier for me to do the cuts I wasn't able to do well before.  Now I can't see being without it.  However, I still love my Festool for breaking down sheet goods as my shop is way too small to do that on a table saw.  I get excellent cuts with the Festool track saw using it this way.  I say it is nice to have both.  Of course, also I am way to old to be trying to muscle full sheets of plywood on a table saw anyway.  You may be much younger and better suited to that.

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 64 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined