Recommended Posts

Posted

So far I've been using my belt sander or my router to round the end grain sides on a board. I wanted to do it with hand tools, so I put my block planes to work. Other than scratching the sole of my plane and some tear out, I'm not getting good results. I think maybe rasps could do the job, but mine are a bit on the coarse side so I didn't try them.

What's the best hand tool or technique for this task?

Posted

If I use hand tools I always do what you are doing. I use a block plane to establish the roundover, working in from both ends to avoid tear out, and finish with hand sanding. You can use a rasp as well and finish up with hand sanding it should work with little to no tear out.  As long as a router doesn't burn the end grain I just use a router though.

  • Like 1
Posted

everything said already ... but he did ask what the _best_ hand-tool would be, so especially for a larger roundover >1/4" I'd say go 75% of the way with the block-plane, then to 99+% of the way with a moulding plane, finish with sand-paper if you really have to.

  • Like 1
Posted

Assuming that your wood is not 'cumbly', i.e. brittle grain that breaks away, get the shape right with a very sharp block plane then go straight to an engineers file, preferably one that is a bit worn. Rub it down the grain, from high spot to low, in straight, even strokes, following the contour.

It will produce a surface that is ready for a mild abrasive, say 240 grit, followed by the finish of your choice. 

I've used this approach for 40 odd years and it works well on most timbers.

Good luck

  • Like 2
Posted

Yep, block plane.  If the wood is soft like fir or pine, hand tools have to be ridiculously sharp to slice fibers as opposed to just pushing then over.  If it is poplar or harder you handplane should do fine.  If not, sharpen.

GnG Low CoD (202).jpg

  • Like 1
Posted
1 hour ago, sjk said:

And skew the plane

As a matter of fact the first plane I used on the edge was a skew block plane. And that's the one that got scratched (bronze...). So I switched to a regular block plane that could use some extra sharpening

 

1 hour ago, sjk said:
22 minutes ago, Eric. said:

 

Diablo 1/2 in. Rounding Over Bit

You kidding. That plane doesn't even have a handle!

 

  • Like 1
  • 3 weeks later...
Posted

If it scratched the sole of your plane, my guess is there is still some grit from sanding (which will have a negative effect on whatever sharpening you did).  I had that happen on one of my first cutting boards, now my rule is sandpaper only after all the planing is done.

As far as tear out; always go from the long grain to the end grain with your strokes(or skew) and not the other way

  • Like 2
Posted

For large radius, If the board in question is not too unweildy, and you could take the corners off quickly with the table saw with the blade set at 45 deg.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 53 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined