Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Cabriole Thing

Featured Replies

  • Popular Post

After the prototype I've started into this. It could be a jewellery box, but really it's just a skills building exercise.

Lay out the legs:

http://IMG_1631_zpsubbdvohn.jpg

Rough them out on the bandsaw:

http://IMG_1638_zps5vkj5ebh.jpg

Rough shaping of the legs:

http://IMG_1639_zps2bs39ekf.jpg

They're a little stouter than the prototype:

http://IMG_1644_zpsnary9b0k.jpg

Did up some front/back and sides:

http://IMG_1646_zpsevqqxzvo.jpg

Dry fit:

http://IMG_1645_zpsrb4sawlo.jpg

  • Replies 632
  • Views 80.1k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Some final photos of the Thing: The doors don't close firmly because of the SOSS hinges (I don't recommend them) so I will probably add some magnets, but that shouldn't c

  • I am having fun watching this journals progress ! It reminded me of a chair I discovered in one of the Smithsonian art furniture galleries.

  • I cut the half lap on the doors: http:// http://

Posted Images

  • Author
25 minutes ago, h3nry said:

whatever it's going to be, it's looking good already.

Thanks h3nry! I think I see you're setting up to do some carving on the legs of your latest project. I'm looking forward to what you come up with.

Would like to see more pictures in between steps. You are like a tv show, they get a ton of work done in a commercial break. Looks very nice!

Very cool Dave ! Hard to tell on my phone, is that walnut you have there?

Sent from my SM-N910W8 using Tapatalk

I'm assuming it's this work computer but, none of the pictures are there for me..  Bummer as I was looking forward to this one when you mentioned it in the prototype leg thread.. 

  • Author
5 hours ago, Rex Edgar said:

Would like to see more pictures in between steps. You are like a tv show, they get a ton of work done in a commercial break. Looks very nice!

Thanks Rex. I'll try to post more detail during the carving.

1 hour ago, wtnhighlander said:

Doing claws on the feet, Dave? You are certainly off to a good start!

Yes, I'm going to attempt to make four "identical" ball and claw feet. We'll see how that turns out.

The sweep of the gouge dictates the curvature/size of the ball so I'm waiting for a set of gouges (which should be in today).

42 minutes ago, shaneymack said:

Very cool Dave ! Hard to tell on my phone, is that walnut you have there?

Sent from my SM-N910W8 using Tapatalk

Yeah it's walnut with some pretty good oxidation/fading on one side. I was going to make the sides of some Birch but the legs get a knee block glued on later to make the transition from the knee to the apron. I felt like it would look funny with two species of wood. I think I'll be doing some sort of inlay on the front/back/sides to dress it up. I haven't quite figured out what the lid will look like yet. There will probably be some kind of ornamentation there too.

7 minutes ago, TIODS said:

I'm assuming it's this work computer but, none of the pictures are there for me..  Bummer as I was looking forward to this one when you mentioned it in the prototype leg thread.. 

I think it must be your work computer Kev. You'll have to wait til you get home...;)

  • Author
  • Popular Post

You can see some remnants of layout lines in this photo.

http://IMG_1639_zpslbmyxxlq.jpg

To begin shaping the legs I use a rasp and card scraper to clean up the band saw marks and the bumps where the blade exits the cuts. Then I scribe two lines along each edge. Then I rasp down to the first line to take off the corner. Next I work towards the second line to round each edge further. They are still a squarish shape with the corners rounded, but after working it more later on the "ankle" should be almost round. At this stage of shaping I need to stay away from the "knee" where the filler block will be attached.

After rasping the corners I hit them with a file and then a card scraper to remove the rasp marks. Always work down hill with the grain if possible. It's not necessary to go too crazy at this point. I'm just cleaning it up to see if they all look close to the same.

Looks great, Dave. Looking forward to seeing the carving. Do you have a tenon jig for the table saw? Looks like you might have been able to cut the square top of the leg on a TS before you took it to the band saw and saved yourself some hand work.

Coming along great Dave! Take a bunch of pics and give us a good play by play when you carve the feet !!

Sent from my SM-N910W8 using Tapatalk

  • Author
On 7/7/2016 at 4:53 PM, Janello said:

Looks great, Dave. Looking forward to seeing the carving. Do you have a tenon jig for the table saw? Looks like you might have been able to cut the square top of the leg on a TS before you took it to the band saw and saved yourself some hand work.

Good point John. I don't have a tenon jig but I get what you mean. The back side of the leg is the milled square surface (marked in blue chalk in the original layout photo). When I cut the pattern on the band saw I stayed about 1/16" away from my line on the surfaces you're talking about. From what I understand I want the extra meat so that I can fair the leg to the apron rather than the other way around.

 

  • Author
  • Popular Post
On 7/7/2016 at 7:01 PM, shaneymack said:

Coming along great Dave! Take a bunch of pics and give us a good play by play when you carve the feet !!

Sent from my SM-N910W8 using Tapatalk

Here goes!

This is my set-up.

http://IMG_1668_zpspjcqbeb2.jpg

I can see how I could end up getting dozens of gouges as I go along but right now I'm using a limited set of tools.

First off I marked my lay out on the piece. The outside circle is the size of the original cylinder I shape when making the ball (shown later). The inside circle is the size of the ball when it's complete. The red lines at the corners are the talons. These can be pretty rough lines at this point.

http://IMG_1650_zpsdtxyk4m9.jpg

 

The sides are marked out as well. The graphite marks are the height and the center line of the ball and need to be consistent on all four legs..

http://IMG_1651_zpsmn4ry8xe.jpg

To start carving I strike in the arch shape and use a V gouge to start into the straight line. As I strike in along side the talons I be sure to keep this cut is perpendicular to the ball so that I'm not undercutting the shape. If I want undercutting it is done later. Right now I'm roughing out the shape.

http://IMG_1652_zpsrwtfvw7f.jpg

Make a cylinder out of what will be the ball working down to the outside line that was scribed on the bottom of the foot(not really pictured, I'll add it later).

http://IMG_1660_zpsrbjp6cm0.jpg

http://IMG_1669_zps9hd8f3fx.jpg

http://IMG_1670_zpsac6zx1lr.jpg

Then start rounding the lower and upper edges of the ball.

http://IMG_1655_zpsseowcv5d.jpg

Then take the bottom of the ball to near the edge of the inside circle( the cut is the shadow in this pic)

http://IMG_1654_zpsrgq8eqlw.jpg.

http://IMG_1655_zpsseowcv5d.jpg

 

 

http://IMG_1656_zps78ngjluo.jpg

The ball is rough at this point. It will be adjusted later. Right now I'm working to my line and moving on to the next surface without taking too much off. Taking tiny little shavings.

After the first side I worked my way around to all four sides.


http://IMG_1657_zpsuewfouoi.jpg

http://IMG_1658_zpsqxbkx8xj.jpg

http://IMG_1659_zpszmqg4vo3.jpg

Right now I have two B n' Cs roughed out.

http://IMG_1667_zpshokzoqcj.jpg

  • Popular Post

I am having fun watching this journals progress !

It reminded me of a chair I discovered in one of the Smithsonian art furniture galleries.

image.jpeg

  • Author
8 minutes ago, wdwerker said:

I am having fun watching this journals progress !

It reminded me of a chair I discovered in one of the Smithsonian art furniture galleries.

image.jpeg

Holy Crap! That's fabulous!

Am I seeing it right? The back legs sway over so the front leg can reach for the ball?

Yep ! Talk about skill. I was by myself and leaned in as close as I could. Craftsmanship was incredible. Guard looked at me funny but when I explained I built furniture and wouldn't touch he left me alone. Can't find my pictures so I grabbed one off the web.

  • Popular Post

I just noticed that the chair has eyes. Freaky!! 

  • Author
  • Popular Post

Today I roughed out the two other B/Cs.

http://IMG_1671_zpsc9dvkqrg.jpg

My next step was to compare each ball and adjust one or another just slightly so that they all look relatively similar.

 

  • Author
19 hours ago, wtnhighlander said:

I'm afraid I would pare them down to pea size, trying to get them alike!

Yeah, there's always the chance that paring things down will get out of hand. I'm really trying to keep it foremost in my mind that nothing is complete. It's all just rough until I make the final cuts, so better have some meat to carve when I get to that point.  I try to identify the high points, take off a small bit at a time, and move on to the next leg while it's still in an unfinished state.

 

My next step is to round and define the fingers and scoop out an area to make the web between them. I mark them out roughly.

http://IMG_1674_zpsfl181ja3.jpg

I also mark out the knuckles using a compass. It's important that all the knuckles are consistent across all four legs.

http://IMG_1677_zpscunyd8rk.jpg

Cut down into the ankle area to scoop out and form the web.

http://IMG_1675_zpscsbbf1dc.jpg

I keep working back and forth slowly, defining the web and rounding the fingers. Here's a comparison:

http://IMG_1678_zpsjbsan9ox.jpg

When the fingers are rounded and somewhat defined. I pare down the claw into a cone. The goal is to get the basic shape but leave some meat for later when I add in the cuticle. I taper the cone to the diagonal layout line in the bottom of the foot.

http://IMG_1680_zpsfj3kr9nv.jpg

http://IMG_1683_zpsrpcwkswj.jpg

So it's coming along on the first B/C. The web is quite low on the ball and the fingers have quite a bit more tweaking to be done. The plan is to take all 16 fingers to this state before refining them much more. I'll be at this for a while. It's slow going.

http://IMG_1682_zpslcxtcoqq.jpg

 

 

Tedious task for sure!  Looking awesome tho!

  • Author
1 hour ago, TIODS said:

Tedious task for sure!  Looking awesome tho!

It's great fun! But I'm super slow and I wish I had more tools!

The back is slightly different than the front. It doesn't get a web between the fingers and thumb.

I work my way down as before.

http://IMG_1685_zpsomfyohqx.jpg

http://IMG_1686_zpsg8k2v3pk.jpg

http://IMG_1687_zps28tht3ad.jpg

On to the fourth side of the first B/C.

http://IMG_1688_zps1y08m6pz.jpg

 

 

  • Author

And now I have one roughed out. The thumb needs a lot of work. I need to watch Phil Lowe's video again and see how it's supposed to go.

Back.

http://IMG_1689_zpsrm9ccavv.jpg

Front.

http://IMG_1690_zpswkokbr6l.jpg

Only three minor cuts on my fingers so far! :)

Next I take the first as an example and try to carve three more that "match".

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.