Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Fence for the bandsaw

Featured Replies

Does anyone have any recommendations/plans for buying/making a bandsaw fence? I've got a 14"bandsaw that I am looking to tune up a bit, but the cheapest fence I can see for sale is $140 and if there's a good way to make one for cheap I'd like to go that route instead. 

  • Popular Post

The cheap(est) route is 2 C-clamps and an "L" shaped fence made from a couple of scraps.  

I've got the 14" Craftsman bandsaw (gasp!) that didn't come with a fence.  The saw is supposedly a copy of the Rikon, and the Rikon fence bolts right on.  Last I checked it's $70 on Amazon.

Cheapest option is what HuxleyWood said. Just clamp a board to the table.

That works fine if you just need a fence for a few cuts but if you are planning a long term solution then a real fence is needed. Frankly unless you have a lot of scrap metal and the skills to cut and weld you are best off just buying a fence. After looking into a lot of options I bought a Kreg fence and I have been quite happy with it. 

https://www.amazon.com/Kreg-KMS7200-Bandsaw-Fence/dp/B0007VYL48/ref=sr_1_1?ie=UTF8&qid=1485260031&sr=8-1&keywords=bandsaw+fence

9 minutes ago, minorhero said:

but if you are planning a long term solution then a real fence is needed. Frankly unless you have a lot of scrap metal and the skills to cut and weld you are best off just buying a fence.

Actually the c-clamp and board option is not all that bad on a bandsaw.  It is far less critical that the fence aligns exactly with blade since the blade is narrow and the kerf wide enough and the blade narrow enough to accommodate a bit of misalignment.

Also a bit more elaborate wooden shop built fence can be quite functional and not that hard to make.

The "real" fence that came with my 14" saw is nice, but I have a shop built fence that I use for re-sawing veneers and other wide thin pieces.  In actual practice it typically stays on the saw most of the time even for setups that would normally be done with the "real" fence.  It works well enough and is less effort than swapping fences.

My little 9" bandsaw didn't come with a fence and I make a lot of small parts on it so after successfully using a piece of wood and two c-clamps for a few years I finally built a fence for it as well.

Yep on the Kreg fence. Only hurts once to buy and you're not messing around with clamps and scrap wood. In the heat of battle it's a lot easier to make the small adjustments with a decent fence. 

 

-Ace-

10 hours ago, bleedinblue said:

I've got the 14" Craftsman bandsaw (gasp!) that didn't come with a fence.  The saw is supposedly a copy of the Rikon, and the Rikon fence bolts right on.  Last I checked it's $70 on Amazon.

I've got the same saw and fence. I'm very happy with both the fence and saw. Just carved up nearly 50 pinewood derby cars for the kids in our pack last month. A great tool, and to my eyes, pretty well built. 

  • Author

Lee Valley just started carrying Rikon bandsaws, so I'll wait a little and see if they start offering the fence for sale separately. With the exchange rate, it's $108 CDN on Amazon, and the Kreg is $140 (ie, same as Lee Valley), so if I can buy it in town it's that much easier to return if it doesn't attach. 

  • 3 months later...

I'm going to bump this because I am now debating between the Rikon fence and the Kreg fence.  Does anyone have any comparison or pros or cons?  

The price difference is about $30.  The Kreg requires drilling and tapping holes into the table.

On 1/23/2017 at 2:58 PM, HuxleyWood said:

The cheap(est) route is 2 C-clamps and an "L" shaped fence made from a couple of scraps.  

So I'll bump this, so you don't stop using the bandsaw while deciding on a fence.

I dadoed a board to fit over the top of my (small) bandsaw table.  It slides toward or away from the blade; I fix it with a quick connect clamp.  It makes the bandsaw usable for reasonably precise cuts (I can do reasonable, and repeatable tenons with it.)  If I had it to do over I'd have used a thicker board (hence the "L shape" that Huxley refers to.)

I do agree that I will eventually get a real fence!!

I think it was the Grizzly fence that I decided was the one I'd buy for my 14" saw, but then I realized how often I'd use it, and decided not to spend the money.  I make out just fine with the 30 seconds it takes to clamp a shop made one in place for the few times i even use a fence.

Tom makes a good point in that you need to determine your use.  The fence and miter gauge both get a good workout on my large bandsaw so they are kept nearby with my blade changing stuff. 

BS-Acc-Rack-Add-(4).jpg.31b3c13b4be21391a626ea3fbe7af2ae.jpg

On the smaller saw I just use a straight edge clamp or a piece of straight scrap.

5915d2fec4db5_BSDeltaFence(1).jpg.f770ce62b3f5daaaef692c4886da6ecf.jpg

5915d2ff6844f_BSDeltaFence(2).jpg.2e34f82d6a6b88b78e34aeecdf47abf8.jpg

The value of a fence and the complexity of one will vary with your use.  I would not want to part with my high/low fence on the larger saw, or give up my miter gauge for that matter.

 

Right now I only really use my bandsaw for ripping rough stock and occasionally long curves, such as curved table aprons.  I feel as though I under use the saw, and thought a real fence might take me a step closer to adding the saw into my usual workflow.

6 hours ago, bleedinblue said:

Right now I only really use my bandsaw for ripping rough stock and occasionally long curves, such as curved table aprons.  I feel as though I under use the saw, and thought a real fence might take me a step closer to adding the saw into my usual workflow.

I think that your instincts are correct - at least they match my own experience.  As soon as I made a fence the bandsaw got more use.  I even used more for stuff that didn't require a fence, just because I was more aware of it and more comfortable with it.  

I don't discourage you from buying a fence, but I also really think it will help you put the bandsaw to use if you construct a "shop made" fence.  Or get hold of the "straight edge clamp" that gee-dub posted a picture of.

51 minutes ago, Pondhockey said:

I think that your instincts are correct - at least they match my own experience.  As soon as I made a fence the bandsaw got more use.  I even used more for stuff that didn't require a fence, just because I was more aware of it and more comfortable with it.  

I don't discourage you from buying a fence, but I also really think it will help you put the bandsaw to use if you construct a "shop made" fence.  Or get hold of the "straight edge clamp" that gee-dub posted a picture of.

I do have a shop made fence that I clamp on when ripping.  It's kind of a pain in the arse though, the bottom of the table has voids that don't play well with the clamps.  Not a big deal, but I usually have to move the clamps two or three times to get em in a secure location.

9 hours ago, bleedinblue said:

I do have a shop made fence that I clamp on when ripping.  It's kind of a pain in the arse though, the bottom of the table has voids that don't play well with the clamps.  Not a big deal, but I usually have to move the clamps two or three times to get em in a secure location.

Cut wood blocks to fit the openings and double-stik tape, silicone rubber or rare-earth magnet them in place.  Great use for a cheap pack of rare earth magnets from HF of the last few blobs in that tube of silcone.

9 minutes ago, gee-dub said:

Cut wood blocks to fit the openings and double-stik tape, silicone rubber or rare-earth magnet them in place.  Great use for a cheap pack of rare earth magnets from HF of the last few blobs in that tube of silcone.

An amazingly simple solution.  

Drill a shallow hole for rare earth magnets to sit almost perfectly flush. They crack surprisingly easy and the pieces are razor sharp ! Or use the metal cups that screw on.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.