freedhardwoods Posted March 11, 2017 Report Posted March 11, 2017 After reading the "I don't get it" thread, I am seriously thinking about buying a Festool sander (or 2). The Festool website lists a Rotex RO 90, ETS 150/3, ETS 150/5, DTS 400, RTS 400, I read what Festool says. I am going to be building cabinets mostly, and other things possibly. Is there one sander that would be a good, overall sander, or would I be better off getting 2 of them for different jobs? If 2 sanders would save 5 or 10 minutes per day over having just 1, it would pay for itself fairly quickly, so the up front cost of 2 doesn't bother me. Quote
drdabrown Posted March 11, 2017 Report Posted March 11, 2017 If you are considering Festool sanders, be sure to plan on getting one of their dust collector's for your sanding station. They are made to go together and you will find that their "CT" dust collector will all but eliminate the dust and make your abrasives last so much longer. I own the RO90, my first Festool purchase with the CT26. It is so versatile with the two heads (the 3" round and the delta head) and perfect for getting into difficult areas like corners and the small size works great on the rails and stiles and edges. My second Festool sander was the ETS 150/3, which is a finish sander with a 3mm orbit pattern compared to the 5mm pattern on the ETS 150/5. I use both of these sanders most of the time. I have found that the RTS 400 is often difficult to control on larger panels due to the excellent suction. I've had to go to skewing the abrasive pad to partly cover the suction holes for it to work on the panel, but it's great for narrower rails and edges, etc., but the RO 90 can do that. The RO 90 also can do much of what the DTS 400 can do because of its shape, but the RO 90 is a little heavier. Therefore, I'd go for the RO 90 & ETS 150/3, but be sure to include one of their CT dust extractor. BTW if you are looking for the perfect sander to sand large panels without the danger of ditching them look at the RS2. Sent from my iPad using Tapatalk Pro Quote
Eric. Posted March 11, 2017 Report Posted March 11, 2017 If you're after a finish sander, ETS 150, either /3 or /5 makes little difference IMO. The /5 will be imperceptibly faster. RO sanders are more for REfinishing...IMO Quote
sheperd80 Posted March 11, 2017 Report Posted March 11, 2017 Depends on the scope of your work really. Since you say you do alot of cabinets i dont think the big rotex sanders are necessary. The ets ec 150/5 is an all around sander that can do rough work and fine finish. Its suprisingly light and controllable with one hand for a 6". Or the cheaper 125/3. I test drove it and its definitely not as aggressive as the 150/5 but for cabinets that may be ok. For face frames and inside corners of panels i think the ro90 would be a great addition but i wouldnt want a 3-1/2" as my go-to sander. Sent from my SAMSUNG-SM-G890A using Tapatalk Quote
Dknapp34 Posted March 11, 2017 Report Posted March 11, 2017 Just got the 150/5 and it is an excellent all around sander, as others have noted. Sent from my iPhone using Tapatalk Pro Quote
Woodenskye Posted March 11, 2017 Report Posted March 11, 2017 I will be a bit different, I really like the RO150 and use it in both modes with great success and actually prefer to the ETS150/3. The RO 90 is good if you do a lot of face frame cabinets. I agree 100% about combining with the dust extractor. If staying in the shop, get the CT26, because that will allow for the boom arm to be attached Quote
Eric. Posted March 11, 2017 Report Posted March 11, 2017 17 minutes ago, sheperd80 said: The ets ec 150/5 is an all around sander that can do rough work Huh? Quote
rodger. Posted March 11, 2017 Report Posted March 11, 2017 I have 150/3 with a ct26. Perfect combo for furniture making. Quote
jussi Posted March 11, 2017 Report Posted March 11, 2017 I'd go with the newer ETS EC models. IMO the ergonomics are much better. The 3 stroke should be fine. I also like the RO90 for sanding face frames because of it's small size it's less likely to tip over and round the edges. Quote
Eric. Posted March 11, 2017 Report Posted March 11, 2017 IMO a more efficient workflow building cabinets would be to run all your parts through the drum sander at 120 grit before joinery and assembly so only finish sanding needs to be done afterward. I don't see the usefulness of any RO sander in cabinetmaking. For refinishing or slab work, the RO150 would be great for heavy material removal; and the RO90 is great for the final stages of sculpting and curved work. But for flat work I don't think the RO sanders fit into any efficient workflow. If you could only afford one sander and you needed a jack of all trades, then the RO makes more sense. For finish sanding, buy a finish sander. Quote
Llama Posted March 11, 2017 Report Posted March 11, 2017 I have two Festool sanders... The 5" Rotex and the 5" finish sander (the one that's around $200) Those two sanders get me through anything I've needed. I will end up picking up the smaller Rotex for sanding areas the 5" can't get to. What works for me is to use the Rotex on the geared mechanism up to 150-180 or whatever, then repeat that grit on the finish sander and finish up with higher grits if you want. Quote
Gnarlywoodguy Posted March 11, 2017 Report Posted March 11, 2017 ETS150/5 and RO125 plus a CT26. Sent from my iPhone using Tapatalk Ask 10 woodworkers you'll get 11 answers. Sent from my iPhone using Tapatalk Quote
ben_r_ Posted March 11, 2017 Report Posted March 11, 2017 Pro 5 and ETS EC 150/3 with a CT36 here. Been much nicer than any cheaper setup Ive owned previously. Same goes for all the other Festool products I own. Really it some top notch stuff. Just wish it was cheaper. Planning to add a DTS 400 REQ for tight spaces and edging soon. Quote
Eric. Posted March 11, 2017 Report Posted March 11, 2017 20 minutes ago, Gnarlywoodguy said: ETS150/5 and RO125 plus a CT26. Only problem with that is now you have to buy two sizes of paper. But let's not go there again. 2 Quote
Brendon_t Posted March 11, 2017 Report Posted March 11, 2017 2 hours ago, Eric. said: Only problem with that is now you have to buy two sizes of paper. But let's not go there again. Or let's. Quote
Barron Posted March 11, 2017 Report Posted March 11, 2017 I have the 150/5 and the RO90 and find it's a good combo. The RO90 is handy for shaping chair legs and seats using coarse paper, and the 150 for everything else. Oh, and the delta pad on the 90 works well in corners. Quote
HuxleyWood Posted March 12, 2017 Report Posted March 12, 2017 I have a few Festool sanders RO90, RO150, ETS EC 150, Pro 5, DTS, RS 2 and have had a couple of others in the past. if you are getting one Festool sander for general woodworking I think the ETS EC 150/5 (note the EC is the brushless version and a whole different ballgame than the non-brushless version and nearly as good as the Mirka Ceros/Deros). I also have a soft spot for the RO90 and find all sorts of uses for it on both flat and sculpted work and despite the fact it looks unwieldy it is usually my go to sander for tight corners and other detail sanding. If I had to drop down to only two hand sanders it would be the RO90 and the Mirka Deros 650 (or in keeping with the Festool theme the ETS EC 150). Honestly, I think the best thing to do is go actually play with them at a dealer and see for yourself the capabilities and the ergonomics of each one, the path will be much clearer them. I don;t worry too much about having extra sized sandpapers, I have about 6 different "sets". If you do enough work to make owning multiple Festool sanders sensible then you will go through a decent amount of paper and the only issue is the first time kit out. I also find that while there is some overlap I often don't have the full range of grits in any one size since some sanders fit naturally into a particular grit range. You will want a good vacuum setup and Festool makes very good ones but it doesn't have to be a Festool, especially if you want to spread out the purchases, though you do get a 10% discount on the extractors when you bundle it with a tool. Whatever you get for the long run I suggest you get quality hoses, I really prefer 27mm hoses with sanders and while the 33mm Bosch is good and cheap I will pay the extra money for a 27mm Festool for sanders. I also suggest you run a Plug It cord in a hose sleeve with the vac hose, sanding will be much more pleasurable only dealing with one appendage that doesn't catch on everything! Quote
sheperd80 Posted March 12, 2017 Report Posted March 12, 2017 Huh? Meaning its aggressive enough to sand down rough surfaces... IMO ;-) Sent from my SAMSUNG-SM-G890A using Tapatalk Quote
Eric. Posted March 12, 2017 Report Posted March 12, 2017 1 minute ago, sheperd80 said: Meaning its aggressive enough to sand down rough surfaces... Well, sure...I mean on a long enough timeline jagged rocks become smooth pebbles in flowing water. I wouldn't classify ETS sanders as "aggressive" on any scale. They can sand down rough surfaces, but it takes fo-eva. That's a job for the RO. Quote
freedhardwoods Posted March 19, 2017 Author Report Posted March 19, 2017 Thanks for all the replies and info. It gives me plenty to think on before I get my sanders(s). Quote
wdwerker Posted March 19, 2017 Report Posted March 19, 2017 For years I used my ETS 150/3 with a Fein vac w a HEPA filter. I did have to drill some holes in the hose end plastic to regulate the suction (too much suction leads to wearing out $40 pads quickly ) . If I was getting one sander I would get the ETS 150/5 today. I just got one last year and it does take down uneven joints a little faster. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.