Popular Post Pondhockey Posted June 10, 2017 Popular Post Report Posted June 10, 2017 (edited) My wife (aka "the Boss") requested a table for the deck in our new house. We settled on Mark's "Not So Rustic..." (NSR) table as something suitable that I might be able to handle, and could be adapted to our situation. The wood is Western Red Cedar, generally used for decking (and was use for our deck). Mark's plans were too long for the space, and we wanted to put a chair on either end, so we shortened and widened the design and moved the cross bracing up a wee bit to make room for feet on the end. Here is the table: The table top was tricky for me. I used flat sawn 2X8, joining two at a time, with opposing grain curvature, but this produced a cupped pair. I planed all pairs at the same time to produce an even thickness, but did not achieve truly flat pairs, so despite running again across the jointer, I did not have truly perpendicular edges - when put together, there was a larger gap than I expected. I finally ripped a kerf width off at the table saw, with the pairs oriented cup down. and called it good enough. Below is an image of the pairs being glued, with the base assembly in the background. By comparison, the base assembly was less troublesome for me, and even stands square without rocking (I was shocked, but later figured out why.) Not having a domino mortise cutter, I went with mortise and tenon joints. A few tenons cut on the bandsaw, and then after discussion on here I followed Eric's guidance and used the table saw for the rest (and they came out better!) I used a "bump cut" method that I saw on the FWW website since I didn't have a tenon jig. I had just acquired a drill press with mortise bit/chisels so that's how I cut most of the mortises. Below is the end view of the table: no breadboard end, cross structure raised for foot/leg room. I used battens rather than buttons to join the top to the base. I didn't appreciate just how sloppy the work was until posting it! Some cleanup is in order. Fairly tight joint (for me): Fairly gappy joint (even for me): The table looks better from a distance! But it's an outdoor table and the Boss is appreciative. I finished it with "Clear Penetrating Epoxy Sealer" to protect against the outside central Idaho weather, and then with spar varnish for UV protection. If there's interest, I'll provide an update in a year or so on how well the finish lasts. Edited June 10, 2017 by Pondhockey happy joint -> gappy joint 5 Quote
mat60 Posted June 10, 2017 Report Posted June 10, 2017 That is a fine looking outdoor table and I bet the boss likes it. 1 Quote
wtnhighlander Posted June 11, 2017 Report Posted June 11, 2017 Lovely grain selection for the top, too! 1 Quote
Pondhockey Posted June 11, 2017 Author Report Posted June 11, 2017 I appreciate the comments, guys, thanks. My own take is that I need more work on: - finishing (always), especially using epoxy to fill voids. I didn't mention, or show, but my attempts to fill three small voids from knots failed. - joinery. A discussion on this forum about cutting tenons using the table saw was helpful and improved that part of things for me, but the joints still were not always square and tight. - jointing, planing and gluing boards for a table top. I might have done better with quarter sawn boards (which I actually picked out. Due to miscommunication, the flat sawn boards were cut to length and loaded in my truck while I was paying for the boards!) The flat sawn sections did result in nice figure, that Highlander noted, but I struggled with making the boards flat and the edges perpendicular. So I guess I need practice/improvement on about everything! I'll Probably listen better when these topics come up. 1 Quote
Chet Posted June 12, 2017 Report Posted June 12, 2017 I really like the top. Some really gray looking grain. Quote
bleedinblue Posted June 12, 2017 Report Posted June 12, 2017 That's a great table for a deck. Quit pointing out your errors...those aren't even visible unless you crawl under the table. You know what you need to improve on, everyone else doesn't have to know. 2 Quote
Troy Posted June 12, 2017 Report Posted June 12, 2017 Nice table... Always fun to complete a Boss pleaser. Quote
shaneymack Posted June 12, 2017 Report Posted June 12, 2017 Turned out great! Nice work Sent from my SM-N910W8 using Tapatalk Quote
lewisc Posted June 12, 2017 Report Posted June 12, 2017 The top looks great! Will you do some matching benches? Quote
Popular Post Pondhockey Posted June 13, 2017 Author Popular Post Report Posted June 13, 2017 1 hour ago, lewisc said: The top looks great! Will you do some matching benches? Thanks, Lewis. I did one bench, as practice before doing the table. I originally thought it would wind up at our uncovered sitting area, but for the time being it has been privileged to reside in the covered deck area. 4 Quote
Steve B Anderson Posted June 13, 2017 Report Posted June 13, 2017 Very nice work! That will definitely kick your deck up a notch. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.