jpf1182 Posted September 6, 2017 Report Posted September 6, 2017 Is it worth the extra money to buy a jointer with parallelogram beds? I understand they are much easier to adjust. I will insist on spiral cutter head. Any thoughts? Thanks. Quote
Eric. Posted September 6, 2017 Report Posted September 6, 2017 No-brainer if you're buying new. Quote
Tom King Posted September 6, 2017 Report Posted September 6, 2017 I've never owned anything but a wedge bed with straight knives, so sorry, I can't offer advice. Of the three jointers I own, only one required adjusting, and that 8" Delta came from a school auction in 1975. It's been so long ago when I straightened up that one, that I don't really remember exactly how I did it. I was young and inexperienced then, so it couldn't have been too bad. Quote
gee-dub Posted September 6, 2017 Report Posted September 6, 2017 Parallelogram beds were one item on my short list of "must haves" when I shopped for a new jointer. I imagine if you have never had the 'pleasure' of aligning dovetail-way beds you wouldn't consider it. I never wanted to have that fight again (partial disassembly and shims versus turning a cam). I went with the Grizzly G0490X about 10 years ago as it was the best bang for the buck at that time. There are more elegant machines but, the nearest competitor back then was $1000 more and showed no real signs of being a superior product. There are probably more choices today so do your own comparison. The carbide insert head paid for itself long ago in saved sharpening and replacement knife costs. The ensuing savings are more than enough for a replacement set of inserts (that I already picked up at a special price a couple years ago). Make a short list of your desired features and then compare the makes and models that fit your list. If it helps, my list was something like: P-beds Carbide insert head Long infeed Tall fence Mobility (built in or easily fit) Quote
jpf1182 Posted September 6, 2017 Author Report Posted September 6, 2017 Thanks. I am looking at the Grizzly but they have been on back order for months. I also don't want to pay another $1000 for a similar product . 95% of the reviews have been on the very positive side for the Grizzly. Guess I will wait until they are available. Thanks again for your replies. Quote
gee-dub Posted September 6, 2017 Report Posted September 6, 2017 39 minutes ago, jpf1182 said: Thanks. I am looking at the Grizzly but they have been on back order for months. I also don't want to pay another $1000 for a similar product . 95% of the reviews have been on the very positive side for the Grizzly. Guess I will wait until they are available. Thanks again for your replies. If you decide to go that way, I'd go ahead and place your order. That way you're already in line. There's a reason these things are on back order and I don't know if we actually know what it is. Obviously the old Delta DJ 20 design is reliable enough to have spawned several clones, all seem popular enough to cause people to wait for one :-) Quote
Eric. Posted September 6, 2017 Report Posted September 6, 2017 2 hours ago, jpf1182 said: Thanks. I am looking at the Grizzly but they have been on back order for months. I also don't want to pay another $1000 for a similar product . 95% of the reviews have been on the very positive side for the Grizzly. Guess I will wait until they are available. Thanks again for your replies. "Similar" is not the same as..."same." DAMHIK Quote
QHC Posted September 6, 2017 Report Posted September 6, 2017 You could buy the W1741W Shop Fox and add the sprial head for about 1600 Sent from my SM-N920P using Tapatalk Quote
collinb Posted September 6, 2017 Report Posted September 6, 2017 4 hours ago, jpf1182 said: Thanks. I am looking at the Grizzly but they have been on back order for months. I also don't want to pay another $1000 for a similar product . 95% of the reviews have been on the very positive side for the Grizzly. Guess I will wait until they are available. Thanks again for your replies. In a back-order situation waiting seems unproductive. One should enter the queue. Quote
Pwk5017 Posted September 7, 2017 Report Posted September 7, 2017 Ive only ever purchased parallelogram bed jointers--mostly because of Marc and this forum-- of which ive never had to adjust. However, last year i did adjust a friend's jet dovetail way machine. I warned him i have never adjust a DT jointer before and not to expect much. It went from being an expensive 500lb turd to giving him clean joints in about 20-30 mins. The outfeed table was sagging about 1/8" when i laid my veritas straight edge on the beds. Two shim attempts later it was ready to have the gib screws tightened. His machine has a byrd head in it, and i want to say i ended up shimming the cutterhead too during this process. Long story short, i went in thinking it was going to be a 6 hour ordeal and it ended up being easy. That 8" jet machine still sucks and i would advise everyone to avoid it like the plague, but calibrating it wasnt dreadful. Quote
woodbutcher Posted September 7, 2017 Report Posted September 7, 2017 What did you use for shim material? What dont you like about that Jet jointer? Ive had my eyes on a new 6" Jet. Quote
Eric. Posted September 7, 2017 Report Posted September 7, 2017 44 minutes ago, woodbutcher said: What did you use for shim material? What dont you like about that Jet jointer? Ive had my eyes on a new 6" Jet. If you're looking at Jet you might as well save some money and buy a Grizzly or spend a little more and get the PM. The Jet is in no-man's land when it comes to bang for your buck. Grizzly is the best value and PM is the best quality among the hobbyist options. Jet is closer to Grizzly quality and PM price. Wrong direction on both ends. Or you can lose your mind and Felderize yourself like @Llama and have everyone mumble bad words about you under their breath. Those are the real machines. We have toys. Buy the best toy you can afford. Quote
mat60 Posted September 7, 2017 Report Posted September 7, 2017 On 9/6/2017 at 0:34 PM, QHC said: You could buy the W1741W Shop Fox and add the sprial head for about 1600 Sent from my SM-N920P using Tapatalk I have the Shop Fox / Grizz jointer blade unit and have never got it set up to where im happy with it. Its ok but a jointer needs to be dead on. Some have luck with them. I would never get anything less than a PM now. A table saw is one thing as all I have is a Jet cabinet saw and its ok Quote
Tom King Posted September 7, 2017 Report Posted September 7, 2017 I remember when I shimmed the 8" Delta, that I sacrificed some leaves out of the feeler gauge set that I used to set the points in my two big blocks. I didn't use the .015 one, because that fit both sets of points. The numbers of people who knew what points were, are fastly dwindling. It was the days of carburetors, and non digital ignition. 1 Quote
QHC Posted September 7, 2017 Report Posted September 7, 2017 If you're looking at Jet you might as well save some money and buy a Grizzly or spend a little more and get the PM. The Jet is in no-man's land when it comes to bang for your buck. Grizzly is the best value and PM is the best quality among the hobbyist options. Jet is closer to Grizzly quality and PM price. Wrong direction on both ends. Or you can lose your mind and Felderize yourself like @Llama and have everyone mumble bad words about you under their breath. Those are the real machines. We have toys. Buy the best toy you can afford. If you know where you can buy a new 8" PM jointer with sprial cutter head for $1600 shipped, please share. My bet is the PM is at least double that. Sent from my SM-N920P using Tapatalk Quote
Eric. Posted September 7, 2017 Report Posted September 7, 2017 1 minute ago, QHC said: If you know where you can buy a new 8" PM jointer with sprial cutter head for $1600 shipped, please share. My bet is the PM is at least double that. I didn't say it was the same price as the Jet...I said, "spend a little more and get the PM." I'm not sure where you're finding an 8" Jet with helical head for $1600. I see $2000 for the JWJ8HH. The comparable PM (60HH) is $2300 and the comparable Grizzly (G0656XW) is $1300. My point being, there's no way the Jet is $700 better than the Grizzly, but the PM is definitely $300 better than the Jet. If you can get the Jet for $1600 then it changes the game. Where do you see that? Quote
estesbubba Posted September 7, 2017 Report Posted September 7, 2017 2 hours ago, woodbutcher said: What did you use for shim material? What dont you like about that Jet jointer? Ive had my eyes on a new 6" Jet. Pop can is great for shim material. Like Eric said, Jet often has less features than Grizzly and costs quite a bit more and probably isn't any better quality. 1 Quote
woodbutcher Posted September 7, 2017 Report Posted September 7, 2017 1 hour ago, Eric. said: If you're looking at Jet you might as well save some money and buy a Grizzly or spend a little more and get the PM. The Jet is in no-man's land when it comes to bang for your buck. Grizzly is the best value and PM is the best quality among the hobbyist options. Jet is closer to Grizzly quality and PM price. Wrong direction on both ends. Or you can lose your mind and Felderize yourself like @Llama and have everyone mumble bad words about you under their breath. Those are the real machines. We have toys. Buy the best toy you can afford. Thanks Eric. The Powermatic equivalent to the Jet I was looking at is only about $150 more. Definitely will go that direction. Why are the parallelogram bed jointers so much more expensive than dovetail way beds? Quote
Eric. Posted September 7, 2017 Report Posted September 7, 2017 Just now, woodbutcher said: Thanks Eric. The Powermatic equivalent to the Jet I was looking at is only about $150 more. Definitely will go that direction. Why are the parallelogram bed jointers so much more expensive than dovetail way beds? More parts, better technology, easier calibration. It's a "nice to have" feature, not a necessity. Shouldn't be a deal breaker but if I were buying new I'd get the parallelogram beds for sure. 1 Quote
Pwk5017 Posted September 7, 2017 Report Posted September 7, 2017 2 hours ago, woodbutcher said: What did you use for shim material? What dont you like about that Jet jointer? Ive had my eyes on a new 6" Jet. I made sure to give him the heads up to order a cheap set of feeler gauges before i came over. Long enough that you can cut them in half and have balance for both points of contact on the ways. The tables have play in them once you loosen the gib screws, so you can easily pick up the bed and put your shims into place. This is where it helps to have two sets of hands. Trial and error will get you really close to perfect. Wow, where to start on the second question. One, i think its way overpriced. Two, i think the design is antiquated. Three, the bed length sucks for the price. Four, hes had issues ranging from set screws giving out and pulleys flying off to the fence not staying square. I agree wholeheartedly with Eric's statements. If you are budget constrained then save your money and get the grizzly. If not, then save for the PM. 2 Quote
QHC Posted September 7, 2017 Report Posted September 7, 2017 I didn't say it was the same price as the Jet...I said, "spend a little more and get the PM." I'm not sure where you're finding an 8" Jet with helical head for $1600. I see $2000 for the JWJ8HH. The comparable PM (60HH) is $2300 and the comparable Grizzly (G0656XW) is $1300. My point being, there's no way the Jet is $700 better than the Grizzly, but the PM is definitely $300 better than the Jet. If you can get the Jet for $1600 then it changes the game. Where do you see that? My bad, it was a Shop Fox w/std cutter W1741W for $1213 shipped, factoryauthorizedoutlet.com. Then add the Grizz spiral head, gets you to about $1600. Sorry about that. Sent from my SM-N920P using Tapatalk Quote
QHC Posted September 7, 2017 Report Posted September 7, 2017 My bad, it was a Shop Fox w/std cutter W1741W for $1213 shipped, factoryauthorizedoutlet.com. Then add the Grizz spiral head, gets you to about $1600. Sorry about that. Sent from my SM-N920P using Tapatalk BTW, The PM60HH is not a parallagram jointer. Sent from my SM-N920P using Tapatalk Quote
Eric. Posted September 7, 2017 Report Posted September 7, 2017 6 minutes ago, QHC said: BTW, The PM60HH is not a parallagram jointer. All three of the jointers I listed were 8", spiral heads, dovetail ways. Quote
drzaius Posted September 7, 2017 Report Posted September 7, 2017 The 6" General (DT) I have now was pretty close to perfect right out of the box, but the one before that was a nightmare. I spent so many hours trying to shim that thing but it fought me at every turn, & I'm pretty mechanically inclined. My next jointer will be at least 8" & most likely parallelogram. It's so crucial for a jointer to be spot on that I'll probably spend buckets of money to get a really good brand like PM or a euro something. Quote
Llama Posted September 7, 2017 Report Posted September 7, 2017 6 hours ago, Eric. said: Or you can lose your mind and Felderize yourself like @Llama and have everyone mumble bad words about you under their breath. Those are the real machines. We have toys. Buy the best toy you can afford. It's true. DAT FELDER is a real machine. Eric has toys. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.