bholland Posted April 30, 2019 Report Share Posted April 30, 2019 Hi everyone. I got a question about building a bench top. I can get 16/4 ash for about 6.50 a bf and 6/4 for 3.50 with 12/4 for 4.90. I would personally like a 3 inch table top or around there. What makes the most sense? Would I try and get 6/4 boards with 3ish-inch increments wide (3.5 wide, 7in wide) or 16/4 boards and set them wide? I can't figure out what is cheaper. I assume I am going to just edge glue them all. I assume I want the cheapest board per board ft but with 6/4, I would probably need about 15 boards. Is that right? Quote Link to comment Share on other sites More sharing options...
Brendon_t Posted April 30, 2019 Report Share Posted April 30, 2019 Ooh man, if I could get 16/4, I happily would use that over a big glue up of 6/4 boards. With no functional difference, I prefer the look of thick sticks for the top. Between face and edge there shouldn't be much of a difference since board footage is a volumetric measurement. 1 Quote Link to comment Share on other sites More sharing options...
wtnhighlander Posted April 30, 2019 Report Share Posted April 30, 2019 As Brendon said, board feet is the same, so 6/4 is your least costly option. I would pick the thinner boards and laminate them, as they are more likely to be fully dried, and less likely to warp or twist. Thick beams look really cool, but if they aren't dry through and through, they can cause trouble. Quote Link to comment Share on other sites More sharing options...
gee-dub Posted April 30, 2019 Report Share Posted April 30, 2019 I agree that thinner boards laminated together will offer more stability and require less re-flattening over time. Depending on how you use your bench, you may re-flatten more often. Some folks cut into the bench and scar it with chisel, saw and other marks and then re-flatten once things get too chewed up. I use a bench hook and other such items since my preferred bench top is laminate layers of ply and MDF. Any errant scars of any size get filled with epoxy and flattened the next time I am using some. Oddly, the deepest scar on my bench came from dropping something on it from the rafters, not woodworking 1 1 Quote Link to comment Share on other sites More sharing options...
drzaius Posted April 30, 2019 Report Share Posted April 30, 2019 Yes, many thinner laminations will give a more stable top that fewer, thicker pieces, even if it is properly dried. My 3.5" thick bench top is made of 3/4 hard maple laminated & is very stable. But I agree with @Brendon_t that it doesn't look a good as if it were made of 2 or 3 bigger boards. Quote Link to comment Share on other sites More sharing options...
Brendon_t Posted April 30, 2019 Report Share Posted April 30, 2019 So it sounds like everyone's scared of wood movement and reflattening in the future.. But why? We all know it should be dry no matter what thickness so Getting properly dried lumber should make this all but a non issue. Building with 16/4 would be a LOT faster and waste much less wood. Instead of face jointing and planing 20 6/4 sticks which still remove thickness from each, I would happily do 7 16/4 with less than half the glue ups. After movement and ease of work, you have looks: totally subjective but imo, thicker looks better Quote Link to comment Share on other sites More sharing options...
Chestnut Posted April 30, 2019 Report Share Posted April 30, 2019 33 minutes ago, Brendon_t said: So it sounds like everyone's scared of wood movement and reflattening in the future.. But why? We all know it should be dry no matter what thickness so Getting properly dried lumber should make this all but a non issue. On the face i agree with you entirely. In practice i have a bench that isn't flat and it bothers me a ton. Have i flattened it? Nope I'd rather build projects than flatten my bench. On the flip side the time i save now can get me back to projects faster and then i can invest time in the future to re-flatten it when i might have more. This is appealing to me and i might try and find some nice thick stuff to make my bench from. From my reading it seems like there is no avoiding re flattening your bench either it's just how long until you have to. Quote Link to comment Share on other sites More sharing options...
drzaius Posted April 30, 2019 Report Share Posted April 30, 2019 1 hour ago, Brendon_t said: So it sounds like everyone's scared of wood movement and reflattening in the future.. But why? We all know it should be dry no matter what thickness so Getting properly dried lumber should make this all but a non issue. Building with 16/4 would be a LOT faster and waste much less wood. Instead of face jointing and planing 20 6/4 sticks which still remove thickness from each, I would happily do 7 16/4 with less than half the glue ups. After movement and ease of work, you have looks: totally subjective but imo, thicker looks better Once wood is properly & fully dried, that's not the end of movement. Seasonal RH easily varies by tens of percent, so it's gonna move. The twisting & warping is usually minor enough to not be an issue in the case of furniture, but with a bench, I want it to be as flat as possible season to season. I might expect to have to flatten that bench (I haven't with mine) at some point a year or 2 after construction but beyond that I'd rather be using the bench than flattening it. I have no argument with you regarding looks. Quote Link to comment Share on other sites More sharing options...
Brendon_t Posted April 30, 2019 Report Share Posted April 30, 2019 2 hours ago, Chestnut said: On the face i agree with you entirely. In practice i have a bench that isn't flat and it bothers me a ton. Have i flattened it? Nope I'd rather build projects than flatten my bench. On the flip side the time i save now can get me back to projects faster and then i can invest time in the future to re-flatten it when i might have more. This is appealing to me and i might try and find some nice thick stuff to make my bench from. Imo, if you work on it and it's made of wood, you'll like have to flatten it eventually. You're working on your bench that's out of flat and you don't care to flatten it so it's not that big of a deal to you. Honestly, it isn't to me either. But I still haven't heard anything that's different between the glue ups that make a difference Like stated below, Even if you don't work on it, seasonal changes may make it needed anyway... Sooo... With that said.. why not go with the easiest construction? 1 hour ago, drzaius said: Once wood is properly & fully dried, that's not the end of movement. Seasonal RH easily varies by tens of percent, so it's gonna move. The twisting & warping is usually minor enough to not be an issue in the case of furniture, but with a bench, I want it to be as flat as possible season to season. I might expect to have to flatten that bench (I haven't with mine) at some point a year or 2 after construction but beyond that I'd rather be using the bench than flattening it. It feels to me like were giving advice that we don't follow because of an ideal.. Quote Link to comment Share on other sites More sharing options...
Popular Post Ronn W Posted April 30, 2019 Popular Post Report Share Posted April 30, 2019 I come down on the side of using 6/4 and more pieces. Hint. when you laminate the pieces, try to have all the peices with the grain in the same direction, so that if you ever use a plane on it, you 1won't get tearout. 6 Quote Link to comment Share on other sites More sharing options...
Chestnut Posted April 30, 2019 Report Share Posted April 30, 2019 18 minutes ago, Ronn W said: I come down on the side of using 6/4 and more pieces. Hint. when you laminate the pieces, try to have all the peices with the grain in the same direction, so that if you ever use a plane on it, you 1won't get tearout. This is excellent advice in more than just bench making. 1 Quote Link to comment Share on other sites More sharing options...
Brendon_t Posted April 30, 2019 Report Share Posted April 30, 2019 1 hour ago, Ronn W said: I come down on the side of using 6/4 and more pieces. Hint. when you laminate the pieces, try to have all the peices with the grain in the same direction, so that if you ever use a plane on it, you 1won't get tearout. Can you give any reason as to why you come down there? Good hint too no matter the thickness used. Quote Link to comment Share on other sites More sharing options...
drzaius Posted April 30, 2019 Report Share Posted April 30, 2019 2 hours ago, Brendon_t said: It feels to me like were giving advice that we don't follow because of an ideal.. Not at all. To each their own. I just wanted to make clear my rationale & to inform others of the implications of the lumber choices made. I know sometimes I come off as being preachy, but that's not my intention at all. I think I get it from my dad, who was the master lecturer of all time 1 Quote Link to comment Share on other sites More sharing options...
Brendon_t Posted April 30, 2019 Report Share Posted April 30, 2019 36 minutes ago, drzaius said: Not at all. To each their own. I just wanted to make clear my rationale & to inform others of the implications of the lumber choices made. I know sometimes I come off as being preachy, but that's not my intention at all. I think I get it from my dad, who was the master lecturer of all time I'm not trying to start crap or call anyone out. I just can't figure out why people would recommend more glue ups, more milling, more room for error and use thinner lumber when Both are presumably equally dry, both being face glued giving edge grain show faces. I've seen many threads over the years when someone asks about gluing together 845, 4/4 boards for a top and everyone tells them to get thicker lumber. Now, someone has the option and is told to go thin and I haven't heard a reason that isn't the same with both.. If the general idea is that the 3.5" thick dressed lumber will move substantially More, than 1.5" in a glue up, enough to warp your whole thing, while also acknowledging that most people will flatten their bench regardless of thickness of laminations, And knowing it's so little of an issue that some leave it....., I can't get on board. I'm confused honestly and trying to follow the train of thought. Quote Link to comment Share on other sites More sharing options...
Art Posted April 30, 2019 Report Share Posted April 30, 2019 33 minutes ago, Brendon_t said: I'm not trying to start crap or call anyone out. I just can't figure out why people would recommend more glue ups, more milling, more room for error and use thinner lumber when Both are presumably equally dry, both being face glued giving edge grain show faces. I've seen many threads over the years when someone asks about gluing together 845, 4/4 boards for a top and everyone tells them to get thicker lumber. Now, someone has the option and is told to go thin and I haven't heard a reason that isn't the same with both.. If the general idea is that the 3.5" thick dressed lumber will move substantially More, than 1.5" in a glue up, enough to warp your whole thing, while also acknowledging that most people will flatten their bench regardless of thickness of laminations, And knowing it's so little of an issue that some leave it....., I can't get on board. I'm confused honestly and trying to follow the train of thought. I agree. If I had the option (without spending a fortune) I would have to loved to use 12/4 or 16/4 lumber for my bench. 1 Quote Link to comment Share on other sites More sharing options...
wtnhighlander Posted May 1, 2019 Report Share Posted May 1, 2019 Well, there is also the fact that the 6/4 mentioned above is $3 less per board foot. Quote Link to comment Share on other sites More sharing options...
Art Posted May 1, 2019 Report Share Posted May 1, 2019 4 minutes ago, wtnhighlander said: Well, there is also the fact that the 6/4 mentioned above is $3 less per board foot. To me, that's the big factor, particularly on a project that uses as much lumber as a bench top. Quote Link to comment Share on other sites More sharing options...
Popular Post Chestnut Posted May 1, 2019 Popular Post Report Share Posted May 1, 2019 So now that we're all worked up.... . What is the consensus on shorts. If some of the lamination in the top are 2 shorter boards ended together is that bad? In my mind i can't see how it would make a difference especially if they have a floating tenon or 2 between them. I'm asking for a friend that may or may not have a lot of 8/4 cherry shorts they don't know what to do with . 2 1 Quote Link to comment Share on other sites More sharing options...
Popular Post drzaius Posted May 1, 2019 Popular Post Report Share Posted May 1, 2019 Okay, let's look at a top that is make of 3 pieces of lumber, all properly dried, milled & glued up. When moisture content changes, as with the seasons, the wood moves. But wood does not move in a perfectly linear fashion throughout the board. What will happen is that the board will twist, cup, or curve slightly. With only 3 boards in the top, that's going to mean the top is going to go out of flat. Our next top is made of a series of 3/4 boards all glued up to give us that same size & thickness top. Then we get some seasonal moisture changes and the accompanying movement. But in this case, each small board is moving in its own way, and because each board is just a small part of the whole, those movements will work to cancel each other out. One board tries to curve a little to the left, while the other attempts a little curve to the right, and so on. The law of averages sees to it that the overall deviation from flat will be minimized. Of course, there are workbench tops all over the place that stay flat, but there are also many that just don't. My goal was to maximize my chances of getting a top that would stay flat, so I went the route of lots of milling & gluing. There are other factors as well. I enjoy milling and I enjoy glue ups. And last, but not least, 4/4 maple was $1.90/bf vs $6.50/bf for 12/4 maple. But the overriding goal was to get a good, heavy, stable top. My intent was not to claim my way is best, but to express a view that while not popular, presents viable alternate choices for someone who is planning a bench build. 43 minutes ago, Chestnut said: What is the consensus on shorts. If some of the lamination in the top are 2 shorter boards ended together is that bad? In my mind i can't see how it would make a difference especially if they have a floating tenon or 2 between them. Not bad at all. I didn't do any butt joints, but I did glue up a few narrow pieces that were less than the 4" I wanted for the top. 5 Quote Link to comment Share on other sites More sharing options...
Chris208 Posted May 1, 2019 Report Share Posted May 1, 2019 Only my 2 pennies. I built my 8.5 foot roubo using silver maple slabs for everything. I flattened the top 2 years ago, and it’s as flat as the day I finished. That said, I don’t think it matters in use. The decision (as always) is do you want to pay more, or do you want to work harder. Either way you end up with a cool bench. Only you know if you have excess time, or excess money. Chris Quote Link to comment Share on other sites More sharing options...
gee-dub Posted May 1, 2019 Report Share Posted May 1, 2019 19 hours ago, drzaius said: Once wood is properly & fully dried, that's not the end of movement. Seasonal RH easily varies by tens of percent, so it's gonna move. Ding, ding, ding I also use mine as an assembly surface at times so being flat, true and level to mother earth is important to me. This is not the primary use of a workbench. It is a material holding tool and used in that fashion, true flatness is not as much of a concern. We sometimes get caught up splitting hairs on fairly general issues; I apologize for when I contribute to that :) 1 Quote Link to comment Share on other sites More sharing options...
Chestnut Posted May 1, 2019 Report Share Posted May 1, 2019 36 minutes ago, gee-dub said: Ding, ding, ding I also use mine as an assembly surface at times so being flat, true and level to mother earth is important to me. This is not the primary use of a workbench. It is a material holding tool and used in that fashion, true flatness is not as much of a concern. We sometimes get caught up splitting hairs on fairly general issues; I apologize for when I contribute to that Do you level off your bench that often? I know i don't have a level in my shop. I know this because i spent 30 min last night trying to find one. 11 hours ago, drzaius said: Not bad at all. I didn't do any butt joints, but I did glue up a few narrow pieces that were less than the 4" I wanted for the top. This is what i thought. I never see anyone do it in benches. I got quite a few 10 foot boards which would create quite a few awkward length cut offs so i was thinking of just putting them in the center of the slabs. Quote Link to comment Share on other sites More sharing options...
Popular Post pkinneb Posted May 1, 2019 Popular Post Report Share Posted May 1, 2019 Ok i'm not touching this one but...I will tell you having a proper woodworking bench improved the quality of my work. So how ever you make it just get on with it and see how it helps you improve the work coming out of your shop 3 Quote Link to comment Share on other sites More sharing options...
SawDustB Posted May 1, 2019 Report Share Posted May 1, 2019 3 hours ago, Chestnut said: This is what i thought. I never see anyone do it in benches. I got quite a few 10 foot boards which would create quite a few awkward length cut offs so i was thinking of just putting them in the center of the slabs. I don't see any reason not to use shorts. I had some defects in a couple of the long 8/4 boards that I cut out and laminated a piece in, although I just faced it to the bottom. There's so much glue surface in the bench top that even if you didn't reinforce the ends I don't think it's going anywhere. Quote Link to comment Share on other sites More sharing options...
Brendon_t Posted May 1, 2019 Report Share Posted May 1, 2019 16 hours ago, Chestnut said: So now that we're all worked up.... . What is the consensus on shorts. If some of the lamination in the top are 2 shorter boards ended together is that bad? In my mind i can't see how it would make a difference especially if they have a floating tenon or 2 between them. I'm asking for a friend that may or may not have a lot of 8/4 cherry shorts they don't know what to do with . Honestly, I about went with scarf joined shorts when I about ran out of material. I'd have zero issue. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.