Woodworking_Hobby Posted March 4, 2025 Report Posted March 4, 2025 I have a very basic Grizzly 14-inch bandsaw that I am trying to incorporate more into my wood working processes. I have been using it to rough cut parts for my builds and I want to get to the point where I can re-saw wood or use the saw for other functions in the shop. I currently have a 93.5" long 3/8-inch wide AccuRight blade installed. I also purchased the carter upper and lower guide bearings (the ones with the two wheels on the left and right of the blade and the one thrust bearing wheel behind the blade). I also have the EZtension Bandsaw Tension Gauge that I use to try and get the bade set to the correct "tension". It seems like when I tension the blade it is always at a different setting but assume some of that is due to the wear and stretching of the blade as it is used more. When I first turn on the saw the blade seems to run good and does not touch the side or trust bearings. When I make a cut on the saw, the blade seems to touch the upper and lower bearing on the right side of the blade making the bearing wheel spin and will also touch the thrust bearing behind the blade making it spin as well. Sometimes when the blade touches the bearings the saw makes a noise, not really a vibration but almost like a low pitch whine almost like the saw is talking to me, it is a little hard to explain. I know this is a hard question to ask without seeing the saw in action and I am trying to start with is it normal for the blade to touch the side and/or thrust bearings and make them spin when I am making a straight cut or does that mean I have the bearings set incorrectly or the blade not at the right tension? I am not trying to make any curved cuts yet and only doing straight cuts. The saw is actually making a pretty straight cut without much drift that is not super rough. It is by no means smooth enough that you could use for re-sawing without some heavy sanding or a pass through the jointer or especially veneer, but I think I would really need to put in a much wider blade to make those types of cuts like the woodmiser or a re-sawing specific blade. Just looking for any thoughts, suggestions, or experiences you might have had with your bandsaw. Also looking to see if anyone has any good resources they suggest that I can read-up on to get better at using the band saw, to address any setup and operation issues like this, and how to better incorporate it into my work processes. Thanks in advance!!! 2 Quote
Popular Post fcschoenthal Posted March 4, 2025 Popular Post Report Posted March 4, 2025 I think I have the same Grizzly bandsaw (G0555) and run a fairly cheap 3/4" Timberwolf resaw blade on it. Try following this video by Alex Snodgrass to get it set up. He's one of the best. 2 1 Quote
Popular Post Beechwood Chip Posted March 4, 2025 Popular Post Report Posted March 4, 2025 I also have that saw, and I never worry about which bearings are spinning. I assume that the thrust bearing should spin with normal use, but I'm not authoritative. I use it a lot for rough cuts, and always finish on a sander, jointer, planer, etc. 2 1 Quote
Coop Posted March 5, 2025 Report Posted March 5, 2025 On 3/4/2025 at 5:00 PM, Beechwood Chip said: I also have that saw, and I never worry about which bearings are spinning. I assume that the thrust bearing should spin with normal use, but I'm not authoritative. I use it a lot for rough cuts, and always finish on a sander, jointer, planer, etc. +3 My saw makes the same, I guess, noise and when I finally realized that it was not going to blow up on me, I started talking back to it. We’ve been having this conversation for 4 years now. I like the Timberwolf blade for resawing and have been getting great results. 1 1 Quote
Mark J Posted March 5, 2025 Report Posted March 5, 2025 My understanding: When setting up a bandsaw blade with roller bearings all 6 bearings (upper & lower) should be just clear of the blade. But when manually turning the BS wheels even slight finger pressure against the blade's teeth or sides should cause the bearing to turn. 1 Quote
Tom King Posted March 5, 2025 Report Posted March 5, 2025 Sounds to me like it's working about as good as you would expect a 14" saw to. 1 Quote
pkinneb Posted March 5, 2025 Report Posted March 5, 2025 I use the Highland Woodworking Wood Slicer blades (1/2") for all my resaw needs. I also use there set up see the document at the bottom of this web page. https://www.highlandwoodworking.com/wood-slicer-resaw-bandsaw-blades.aspx 1 Quote
Chet Posted March 6, 2025 Report Posted March 6, 2025 On 3/5/2025 at 10:34 AM, pkinneb said: I use the Highland Woodworking Wood Slicer blades (1/2") for all my resaw needs. I also use there set up see the document at the bottom of this web page. https://www.highlandwoodworking.com/wood-slicer-resaw-bandsaw-blades.aspx Plus 1 2 Quote
Coop Posted March 6, 2025 Report Posted March 6, 2025 On 3/5/2025 at 6:17 PM, Chet said: Plus 1 Yo tambien! 2 Quote
Popular Post Chestnut Posted March 6, 2025 Popular Post Report Posted March 6, 2025 The blades should almost always touch the thrust bearings. The side bearings will depend on a lot of factors, in a perfect world the tension would prevent the blade from wandering but in reality it needs help. Assume it'll always be touching one or the other. I like ceramic guide blocks as they are quieter. That said they make a spark show that can sometimes look like fireworks. On 3/4/2025 at 1:19 PM, Woodworking_Hobby said: Just looking for any thoughts, suggestions, or experiences you might have had with your bandsaw. Also looking to see if anyone has any good resources they suggest that I can read-up on to get better at using the band saw, to address any setup and operation issues like this, and how to better incorporate it into my work processes. Use the saw. Use it a LOT. Mine gets used for curve cuts, rip cuts. Some times gets used for short cross cuts that will get further refinement later on. Tilt the table for bevel cuts. Using the saw, wearing out blades replacing blades etc is the only way you'll get better with the tool. The band saw is an odd tool where it just takes experience. If it seems like it's cutting odd after a bit redo the tune up process. If you've ran a lot of material through the balde maybe a new blade is needed. Dulling happens slowly over time so it's hard to say what a dull blade is like but that AH-HA moment after you put a fresh one on will help. Just rest assured that the tool is probably well built and as long as you haven't defeated the safety items, should be safe to operate (blade guards, guides, cabinet doors, etc. The worst thing that can happen under normal safe operation is the blade will break, or jump off the wheel. If you have previously mentioned safety items nothing happens except a noise and the cutting stops. 3 1 Quote
Popular Post gee-dub Posted March 6, 2025 Popular Post Report Posted March 6, 2025 I think everyone has it covered here. I set my guide bearings with a piece of paper or a backlight to place them a few thou away from the blade body. The thrust bearing keeps the teeth from moving back in between the bearings and fouling the set. My thrust bearings come into play immediately as I start the cut. Guide bearings may or may not start to spin based on hardness of material (and therefor blade "bellying", height of cut, feed rate, feather boards or other guide mechanisms, blah, blah, blah. The bearings, blocks, plates, or other guiding materials will contact the blade on and off throughout an operation in my experience. Blade belly can be eliminated with an adjustment of feed rate to match blade condition and material. I think you are generally OK. P.s. That terrible howling that you hear when the bearings engage may mean they are due for a swap. Often it is just movement noise of bearings that are still serviceable. I do recommend buying "tubes" of guide bearings and having them on hand. Like trying to get more life out of your plane irons or jointer knives . . . it doesn't really work out. Guide bearings are disposable items like the brake pads in your car. When they need changing . . . change them 2 1 Quote
wtnhighlander Posted March 7, 2025 Report Posted March 7, 2025 9 hours ago, Chestnut said: If you have previously mentioned safety items nothing happens except a noise and the cutting stops. @Chestnut, you forgot to mention the requisite wardrobe change ... 1 Quote
Chestnut Posted March 7, 2025 Report Posted March 7, 2025 50 minutes ago, wtnhighlander said: @Chestnut, you forgot to mention the requisite wardrobe change ... I was going to but my rambling post was long enough. 2 Quote
Popular Post Woodworking_Hobby Posted March 9, 2025 Author Popular Post Report Posted March 9, 2025 As always thank you for everyone who helped provide some thoughts and suggestions. There are lots of times I would be lost without the insight of this group! I did also emailed Carter, I was not sure if I would get a response as it was just a web form so I posted my question here in the forum as well. Just for info here is the response I got back on their bearings. ——- The bearings should not be touching the blade or spinning under no load. But as soon as you touch the wood to the blade, the bearings will support the blade and spin as you move through the cut. Sometimes only one side will contact the blade, especially when making contour cuts. Other reasons could be that your guide or fence is not actually square to the blade or maybe the set of the blade's teeth is duller on one side than the other, causing a tendency for it to cut slightly in one direction. ( this can happen if the blade was used a lot for cutting circles. If this is the case, try a new blade.) ——- 4 Quote
zxc19 Posted May 15, 2025 Report Posted May 15, 2025 Sounds like you’re on the right track with your setup and asking all the right questions. Yes, it’s normal for the blade to lightly contact the side and thrust bearings during a cut and that’s exactly what they’re there for. The key is to have them just behind the “at rest” blade position so they only engage under pressure. The light whine you're hearing is also pretty common when the blade touches the bearings—especially if it's just grazing them. For resawing, you're spot-on: a wider blade (like 1/2"–3/4" with a low TPI) will help a lot with cut quality and tracking. As for learning resources, I highly recommend Sawblade.tv for video tutorials. it's a great deep dive into setup, tuning, and technique. Also, Alex Snodgrass (from Carter Products) has some excellent setup videos on YouTube that walk through proper alignment in a really clear, practical way. 1 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.