Popular Post Ron Swanson Jr. Posted September 14, 2025 Author Popular Post Report Posted September 14, 2025 Drawer box #2. I'm not crazy about it. I used thicker pieces for the front and back, so the tails are bigger. But it fits respectably and unlike the first one, our stupid cat* isn't going to get the chance to knock it off my bench. --- * Ok, so maybe I'm the stupid one who left it sitting near the edge of the bench and on its side. 6 Quote
Coop Posted September 15, 2025 Report Posted September 15, 2025 On 9/14/2025 at 6:22 PM, Ron Swanson Jr. said: Drawer box #2. I'm not crazy about it. I used thicker pieces for the front and back, so the tails are bigger. But it fits respectably and unlike the first one, our stupid cat* isn't going to get the chance to knock it off my bench. --- * Ok, so maybe I'm the stupid one who left it sitting near the edge of the bench and on its side. Did I/we miss something involving a sweet kitty? 1 Quote
Popular Post Ron Swanson Jr. Posted September 15, 2025 Author Popular Post Report Posted September 15, 2025 On 9/14/2025 at 8:57 PM, Coop said: Did I/we miss something involving a sweet kitty? Lol. More like a cascade of unfortunate events. The first drawer box had a hole in the front, from a slip while cutting the joint. I patched it, and i was planing the patch down, i apparently went too far and 1 largeish hole became 2 small ones. Strike 1. After the glue was applied and before the box was assembled, i realized i forgot to cut a small bit off the back piece. In my rush to make that cut quickly, (glue was already on at this point),i cut the wrong side of the back. This wasn't a huge deal as it was the back of the drawer, but it still bothered me. You can see the back is no longer flush along the top. Strike 2. And then....i had the drawer sitting on its side on my bench. Kitty came in for a visit and jumped up on the bench. He rubbed to on it and it fell off onto the concrete floor. Which took a chunk out in a very visible area. Strike 3. The Culprit on the left, aka Ruthless Overseer of Quality Control: While none of these were catastrophic,i made the decision to make a new one. Box #1 will become a shop box, I'll find a use for it! 5 Quote
Popular Post Ron Swanson Jr. Posted September 15, 2025 Author Popular Post Report Posted September 15, 2025 On 9/15/2025 at 3:01 PM, Coop said: “Kitty litter” shop box? Not sure it's nice enough for those two for that purpose. They're pretty spoiled and would definitely complain about the workmanship. Lol 4 Quote
Popular Post Ron Swanson Jr. Posted September 20, 2025 Author Popular Post Report Posted September 20, 2025 I think I've dragged it this journal long enough. Last steps.... I used a track saw for the cross cuts on the tabletop. Then cut the bevel each side by marking the boundaries on the bottom (1-1/4") and the side grain (1/2") and then just went at it with a 5-1/2, set for a fairly heavy cut. And made some buttons for securing the top. And that's it. Ready for finishing. 6 Quote
Popular Post gee-dub Posted September 20, 2025 Popular Post Report Posted September 20, 2025 Don't stop now. I know what it is like to feel like you have over-shared when something takes longer than you planned. Believe me, many of the things you post that you were thinking about NOT posting will help someone else down the road. Sweet job on the raising on the underside of the top. I have never kept count of how often I touch up my plane iron when raising end grain but it is more than a few before I am done. The leg tapers look good. The scale looks good. I'm not just polishing apples here. It is a good looking piece in a classic form. What are you going to do for pulls? Tell me you're gonna make you own . Demilunes or small drop pulls look great on small pieces like this. A contrasting wood like Peruvian walnut or a curly maple can make them really pop. 4 Quote
Popular Post Ron Swanson Jr. Posted September 20, 2025 Author Popular Post Report Posted September 20, 2025 On 9/20/2025 at 2:45 PM, gee-dub said: Don't stop now. I know what it is like to feel like you have over-shared when something takes longer than you planned. Believe me, many of the things you post that you were thinking about NOT posting will help someone else down the road. Sweet job on the raising on the underside of the top. I have never kept count of how often I touch up my plane iron when raising end grain but it is more than a few before I am done. The leg tapers look good. The scale looks good. I'm not just polishing apples here. It is a good looking piece in a classic form. What are you going to do for pulls? Tell me you're gonna make you own . Demilunes or small drop pulls look great on small pieces like this. A contrasting wood like Peruvian walnut or a curly maple can make them really pop. Thanks for the kind words @gee-dub. They are appreciated. Sadly I'm going to use this black iron pull I bought. It's pretty simple and understated. As to the blade, the answer is 3! I did 2 touch-up sharpenings and then when i got down to the end, i did a very thorough, as-sharp-as-I'm-capable-of-producing sharpening. I also resmoothed the top with that edge and the plane set very, very fine. That old saying is true.. Sharp Fixes EVERYTHING! 4 Quote
Popular Post gee-dub Posted September 20, 2025 Popular Post Report Posted September 20, 2025 No harm in that. I have a couple of shoe boxes full of odd ball cast, stamped or milled knobs. There are times when they are just the thing. IIRC I even used some old VW bug headlamp pull knobs on a piece for a small wall cabinet's drawers. 3 Quote
Popular Post Ron Swanson Jr. Posted September 20, 2025 Author Popular Post Report Posted September 20, 2025 That's awesome. I work out of a couple rail yards and am always picking up old iron track spikes. I really want to use one in as a locking pin on a chest someday. I think it would look really cool. So many plans, so little time! 3 Quote
Popular Post wtnhighlander Posted September 21, 2025 Popular Post Report Posted September 21, 2025 Table turned out beautifully! Hey, you can cut the head off a spike, drill & tap for a machine screw into the cut end, and use that spike head as a drawer pull. The steel on those is soft enough to shape and smooth nicely with a belt sander made for wood. If you happen across any with a double "G" (mirror imaged) embossed on the head, it was made by the company I work for, but a different plant. 5 Quote
Ron Swanson Jr. Posted September 21, 2025 Author Report Posted September 21, 2025 On 9/20/2025 at 9:03 PM, wtnhighlander said: Table turned out beautifully! Hey, you can cut the head off a spike, drill & tap for a machine screw into the cut end, and use that spike head as a drawer pull. The steel on those is soft enough to shape and smooth nicely with a belt sander made for wood. If you happen across any with a double "G" (mirror imaged) embossed on the head, it was made by the company I work for, but a different plant. That's a good idea! And i will keep my eyes out for the GG!! 2 Quote
Von Posted September 21, 2025 Report Posted September 21, 2025 Looks great! Echoing gee-dub, please keep sharing - I enjoy following your work and learn from it. How did you do your bevels on the top? 1 Quote
Popular Post Ron Swanson Jr. Posted September 21, 2025 Author Popular Post Report Posted September 21, 2025 On 9/21/2025 at 7:09 AM, Von said: Looks great! Echoing gee-dub, please keep sharing - I enjoy following your work and learn from it. How did you do your bevels on the top? Hi @Von , thanks for the kind words! I used a bench plane - a 5-1/2 set to a pretty heavy cut for most of it and then to a finer cut at the end. The layout is here in a piece of scrap. Mark one line on the face and 1 in the side and end grain. Hold the plane at that approximate angle and just try not to go past either line. Seems like it would take a while but in reality it was about an hour. 2 2 Quote
Mark J Posted September 21, 2025 Report Posted September 21, 2025 Table looks great. It's a shame those hand planed bevels are hidden on the underside of the top, but that is the table's style. I didn't get the part about the "buttons". How do they hold the top on? 1 Quote
Popular Post Ron Swanson Jr. Posted September 21, 2025 Author Popular Post Report Posted September 21, 2025 On 9/21/2025 at 9:56 AM, Mark J said: Table looks great. It's a shame those hand planed bevels are hidden on the underside of the top, but that is the table's style. I didn't get the part about the "buttons". How do they hold the top on? Thanks @Mark J I took the picture of the buttons before a drilled them, but basically they just hold a screw that goes into the top. I had originally planned on pocket screws to secure the top (notice the hole in the side piece to the right of the button in the first picture?) But i didn't think it through well enough and the 2 pocket holes on the sides ended up getting covered by the spacer pieces. So, i went this way instead. I haven't actually screwed the top into them yet, I'll do that after finishing. 3 Quote
Mark J Posted September 21, 2025 Report Posted September 21, 2025 I get it. A handcrafted "z" clip. 2 Quote
Ron Swanson Jr. Posted September 21, 2025 Author Report Posted September 21, 2025 On 9/21/2025 at 12:29 PM, Mark J said: I get it. A handcrafted "z" clip. Exactly!! 1 Quote
Popular Post Ron Swanson Jr. Posted October 4, 2025 Author Popular Post Report Posted October 4, 2025 All done. I don't know if i have a strong suit in this game, but it definitely isn't finishing. Finish is 2 coats of BLO and 5 of progressively thicker shellac, and paste wax. This was a fun and educational project. Learned a lot and hopefully the next one will be just a little bit better as a result. 5 Quote
wtnhighlander Posted October 4, 2025 Report Posted October 4, 2025 It is hard to imagine how a piece that seems simple can be so elegant. Well done, sir! 1 1 Quote
Von Posted October 4, 2025 Report Posted October 4, 2025 Nice job. The taper on the legs and the dovetails on the drawer are the highlights to me. 1 Quote
gee-dub Posted October 4, 2025 Report Posted October 4, 2025 Came out sweet Ron. Witness marks are definitely your friend when you plane to a line. Love the classic form. A real treat. 1 Quote
Chet Posted October 4, 2025 Report Posted October 4, 2025 That came out really nice. It's always fun to get the finish on a project and bring things to life. Your work really paid off. 1 Quote
curlyoak Posted October 5, 2025 Report Posted October 5, 2025 I enjoyed the ride! One more thing to do, sign and date that heirloom! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.