Popular Post Ron Swanson Jr. Posted August 10, 2025 Author Popular Post Report Posted August 10, 2025 I guess I'll go into a little more detail on a few things. I'm never really sure how much detail to include in these things, and half the time i forget to take pictures anyway. So this morning i was in the shop early and didn't think the neighbors would appreciate hearing my planer before 0600, so i cut and thicknessed the 4 spacers by hand. Here's a little bit on that process, in case anyone struggles with this process. After creating a flat reference face and edge, use a marking gauge referenced off that face to scribe thickness on all 4 sides and darken it with pencil to see it better. Once I start seeing little hairs coming off the side grain, that means I am now hitting the scribe line and it's time to stop or slow way down. Sorry my phone only zooms so much but that's is a little hair and not bench grain that the pencil is pointing at. For quick reference i keep a finished piece right next to the one I'm planing. This really helps me to not go too far. And last thing, I've noticed over time when I'm planing face grain, that the corner below gets cut faster and more aggressively than the rest of the piece. So i try to avoid it early on, bring everything else down to size, and then hit it last. This is a technique issue that's gotten a little better with practice but it's still something i need to watch out for. Next up is the runners and kickers. 4 Quote
wtnhighlander Posted August 10, 2025 Report Posted August 10, 2025 Something I learned to do when thicknessing multiple parts by hand, is to set up a wide stop, and plane them all together. Really helps nail the uniformity. 2 Quote
Popular Post Ron Swanson Jr. Posted August 10, 2025 Author Popular Post Report Posted August 10, 2025 On 8/10/2025 at 9:57 AM, wtnhighlander said: Something I learned to do when thicknessing multiple parts by hand, is to set up a wide stop, and plane them all together. Really helps nail the uniformity. That's a great idea, thanks The thing I'm learning about hand work is that I need to treat it more like machine work and do all operations for a project at one time. I have this bad habit of cutting and fitting a single joint and then moving on to the next one, when i know I'm better served to, for example, cut all the mortises first, cut all the tenons next and then fit each one. This suggestion falls into that camp. I appreciate the suggestion! 3 Quote
Popular Post h3nry Posted August 10, 2025 Popular Post Report Posted August 10, 2025 Enjoying watching this table come together. I find that there are very few pieces that need to be planed to exactly 100% the same thickness, 98% is usually quite good enough. I always use the first piece I do as a reference to compare later pieces with, that way errors do not accumulate over multiple pieces. Ron's technique above is pretty much how I thickness something. 4 Quote
Popular Post Von Posted August 10, 2025 Popular Post Report Posted August 10, 2025 On 8/10/2025 at 12:58 PM, h3nry said: Enjoying watching this table come together. Ditto. On 8/10/2025 at 12:58 PM, h3nry said: I find that there are very few pieces that need to be planed to exactly 100% the same thickness, 98% is usually quite good enough. I have friends who pride themselves on their milling (by hand or machine) to get everything identical and precise. I tend to have a frame of mind that everything will just be a little different, either because that how wood works or because of limits to my skills. In any case, I find not assuming that I will make things identical works well for me. 3 Quote
Chet Posted August 11, 2025 Report Posted August 11, 2025 On 8/9/2025 at 3:09 PM, Ron Swanson Jr. said: taper the 2 inside faces of a leg, This has always been my choice. Looking good so far. 1 1 Quote
curlyoak Posted August 11, 2025 Report Posted August 11, 2025 Some parts need to be the same thickness. Like doors or face plates. I find that the more accurate I dress the lumber the better the project looks and the work is faster. Definitely places that it makes no difference on thickness. I have an 8" delta jointer for face flattening and a neighbor with a 12" jointer and the keys to his shop for the occasional wider piece. I have ripped and rejoined after it gets dressed. With straight grain it is hard to see the joint. If I get lumber s4s I worry abut the thickness side to side. I make sure it is equal across the board. I do find some milled uneven. Already too thin to dress the imperfections. I mostly buy rough lumber. I have been down the rabbit hole trying to build a project and a little too late find out the lumber was not equal across the board. Gave me religion about dressing lumber myself. Before I had thickness planer I would dress one face on the jointer and true it to thickness on my table saw board on edge. No more than 6". My 10" table saw will cut 3" with the blade all the way up. Glad I got the thickness planer. I like taper inside also. I am enjoying the build! Thanks for sharing. 1 1 Quote
Popular Post Ron Swanson Jr. Posted August 17, 2025 Author Popular Post Report Posted August 17, 2025 I got the spacers, runners and kickers installed I was going to attach the top with pocket screws and drilled pocket holes in the 2 sides and 1 in the back. I hadnt considered that the internal pieces would cover the pocket holes on the 2 sides, so had to pivot to a mortise and button attachment for the 2 sides. The pocket hole in the back can stay. Got the drawer sides milled and the bottom glued up though i don't think I'll going to put the drawer together today. 6 Quote
BillyJack Posted August 17, 2025 Report Posted August 17, 2025 Turning out good. Completion is sneaking up on you 1 Quote
Popular Post Ron Swanson Jr. Posted August 24, 2025 Author Popular Post Report Posted August 24, 2025 Drawer box this weekend. Everything was going along fine until i blew through the lap and made a small hole. and tore off a larger part of the lap covering that socket. You can see the larger piece that broke off surrounding the hole. Got that pretty well repaired, but have to deal with that hole. Right now I'm thinking about inlaying a small patch piece, but I'm open to suggestions. Other than that the rest of it went fairly well. This is dry fit. Still working on the bottom and will glue up when that's in. Should've made that lap a little wider. Another 1/32 or so would've made a big difference. 4 Quote
wtnhighlander Posted August 24, 2025 Report Posted August 24, 2025 Ouch, that's a tough break. Drawers look great, though! Personally, I have better luck with inlays that purposefully do not try to match the surrounding wood. That works best if you can incorporate an inlay shape or pattern that covers the damaged area. If you have some scraps from the same board, you might be able to inlay a near-invisible patch. You'll always see it, but almost no one else will. 2 Quote
Popular Post Ron Swanson Jr. Posted August 25, 2025 Author Popular Post Report Posted August 25, 2025 On 8/24/2025 at 6:35 PM, wtnhighlander said: Ouch, that's a tough break. Drawers look great, though! Personally, I have better luck with inlays that purposefully do not try to match the surrounding wood. That works best if you can incorporate an inlay shape or pattern that covers the damaged area. If you have some scraps from the same board, you might be able to inlay a near-invisible patch. You'll always see it, but almost no one else will. That's the plan, i do have some scrap left over to try a patch. Otherwise, worst case scenario,I have one piece of scrap large enough to replace that drawer front. Depends on how ambitious i get. 3 Quote
Popular Post gee-dub Posted August 25, 2025 Popular Post Report Posted August 25, 2025 I say try to repair. If you aren’t happy then replace. I have gotten away with some pretty invisible repairs once the finish is done. I do try to be reasonable about how much time I spend on the repair though. It is easy to get lost down the rabbit hole. 3 Quote
curlyoak Posted August 25, 2025 Report Posted August 25, 2025 when I damage a part or cut something too short I get angry at me. Throw something and or yell at me few foul words. Then I leave the shop for the day and think about what is my best solution....Then a new day, back to the privilege of being a woodworker. Ron, you seem in full control. I admire that! 1 1 Quote
Popular Post Ron Swanson Jr. Posted August 25, 2025 Author Popular Post Report Posted August 25, 2025 On 8/25/2025 at 4:42 AM, curlyoak said: when I damage a part or cut something too short I get angry at me. Throw something and or yell at me few foul words. Then I leave the shop for the day and think about what is my best solution....Then a new day, back to the privilege of being a woodworker. Ron, you seem in full control. I admire that! We have very similar reactions! I drive truck all day which gives me plenty of time to think about next steps on a project. I do my best thinking outside of the shop it seems. 3 Quote
Von Posted August 25, 2025 Report Posted August 25, 2025 The grain around the hole is strong, but consistent. If you can use a scrap from that same piece, I would be optimistic. Given that one strong horizontal grain line, I'd even be tempted to use a brown marker to blend it in if needed. 1 Quote
Mark J Posted August 25, 2025 Report Posted August 25, 2025 If you had a piece of veneer, you could cover over the entire drawer front. That would cover the defect and be a difficult to see repair. 2 Quote
Tom King Posted August 25, 2025 Report Posted August 25, 2025 Not a suggestion, but I would replace the front. Use that one for a back sometime. Are you marking the dovetail with a knife? I never had much luck with knife marking. I only use one if a sharp no.4 pencil tip won't fit in. It is harder for me to leave a knife line than a pencil line. PM me your address and I'll send you some pencils worth using. I like these pencils, but not this much. Besides, these are no.2's. I use 3's and 4's. I have multiple lifetime supplies anyway. https://www.ebay.com/itm/167740240188? Those are pre WWII. After the Japanese bombed Pearl Harbor they changed the name to Mirado and stopped making them in the early 1980's. 1 Quote
Popular Post Ron Swanson Jr. Posted August 25, 2025 Author Popular Post Report Posted August 25, 2025 On 8/25/2025 at 7:58 AM, Tom King said: Not a suggestion, but I would replace the front. Use that one for a back sometime. Are you marking the dovetail with a knife? I never had much luck with knife marking. I only use one if a sharp no.4 pencil tip won't fit in. It is harder for me to leave a knife line than a pencil line. PM me your address and I'll send you some pencils worth using. I like these pencils, but not this much. Besides, these are no.2's. I use 3's and 4's. I have multiple lifetime supplies anyway. https://www.ebay.com/itm/167740240188? Those are pre WWII. After the Japanese bombed Pearl Harbor they changed the name to Mirado and stopped making them in the early 1980's. I use both a knife and a pencil. I scribe the tails onto the pin board with a knife and then go in with a .07 mechanical pencil to darken the line so i can see it better. I also use a jig for transferring. It took me a couple iterations to get this jig just right but i find it's far more reliable than the usual method. The other thing worth mentioning is that i adopted the way that Christian Becksvoort for removing waste, which consists of chopping down on the shoulder line, and then in from the end grain. I find this to be by far the most efficient and cleanest method, and i can do it while seated in a chair. On 8/25/2025 at 7:25 AM, Von said: The grain around the hole is strong, but consistent. If you can use a scrap from that same piece, I would be optimistic. Given that one strong horizontal grain line, I'd even be tempted to use a brown marker to blend it in if needed. Von I have had similar thoughts of filing it with hide glue and dust. Thanks for weighing in! 3 Quote
Ron Swanson Jr. Posted August 25, 2025 Author Report Posted August 25, 2025 On 8/25/2025 at 7:53 AM, Mark J said: If you had a piece of veneer, you could cover over the entire drawer front. That would cover the defect and be a difficult to see repair. Mark i have thought about this too! Definitely a possibility. Thanks 2 Quote
Tom King Posted August 25, 2025 Report Posted August 25, 2025 The offer stands about the pencils. No mechanical pencil will let you put as fine of a line right where you want it as easily. You can skip the knife which puts the line right where you need to leave the line. 2 Quote
Ron Swanson Jr. Posted August 25, 2025 Author Report Posted August 25, 2025 On 8/25/2025 at 10:31 AM, Tom King said: The offer stands about the pencils. No mechanical pencil will let you put as fine of a line right where you want it as easily. You can skip the knife which puts the line right where you need to leave the line. PM sent. Thanks Tom! Quote
Popular Post Ron Swanson Jr. Posted September 7, 2025 Author Popular Post Report Posted September 7, 2025 Back to work on this. Life has been conspiring to keep me out of the shop lately. Drawer bottom gets chamfered for the groove in the two sides and in the front. The back piece is shorter and does not have a groove, to allow for movement. The chamfer gives a nice friction fit. The back: And the top is glued up. Spent some time on it with a smoother this morning and the surface is like glass, it gives a reflection if viewed from an angle. I was happy with how this came out. There's more to be done on the top but I'm hoping to get that done later in the day. 6 Quote
gee-dub Posted September 11, 2025 Report Posted September 11, 2025 Me like-ee Ron. Looking good! 1 Quote
Coop Posted September 12, 2025 Report Posted September 12, 2025 I like the way you treated the bottom! 1 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.