Popular Post Ron Swanson Jr. Posted July 7, 2025 Popular Post Report Posted July 7, 2025 I'm not too far along but thought I'd try to capture the steps as they happen instead of putting together a journal after the fact. This is a pretty straightforward shaker table with one drawer. At least it looks straightforward. Time will tell though. With my dimensions pretty well finalized, i draw them out in chalk on each board. I don't have the 8/4 for the legs yet. I'll get that this weekend and let it acclimate while i work on everything else. For the 2 pieces that will make up the top i flattened 1 face by hand because they're too wide for the jointer. My method is pretty simple. Start with the convex cupped face up and use a scrub plane across the grain to knock it down. This gives me a chance to use the gap stop in my bench as a planing stop. Note: i try to stay away from the corners at this point. Then, winding sticks And when those are playing nice together, it's time to break out the jointer plane. I have a cheap rockler Jointer, but it gets the job done. All that mass helps. Once those big shavings start flying it is very soothing. I could do that all day. I flattened the top face of one side and the bottom face of the other. Because I'm using the jointer for the edges, and this way any little bit that my jointer fence is off from a perfect 90* will be offset between the two pieces and give a nice tight glue line. And that's it for now. 8 Quote
fcschoenthal Posted July 7, 2025 Report Posted July 7, 2025 Looking forward to seeing the progress Ron. I hope the rest goes easier than the first step. 1 Quote
Ron Swanson Jr. Posted July 8, 2025 Author Report Posted July 8, 2025 On 7/7/2025 at 8:34 PM, Coop said: Nicely done! Is that cherry? Yes it is cherry 1 Quote
curlyoak Posted July 9, 2025 Report Posted July 9, 2025 Thank you for sharing your work. Do you have a drawing or sketch you are working with? Quote
Popular Post Ron Swanson Jr. Posted July 9, 2025 Author Popular Post Report Posted July 9, 2025 On 7/9/2025 at 2:51 PM, curlyoak said: Thank you for sharing your work. Do you have a drawing or sketch you are working with? Sort of. Really more working off a picture and made some educated guesses at the sizes of the pieces. 5 Quote
Ron Swanson Jr. Posted July 9, 2025 Author Report Posted July 9, 2025 https://woodandshop.com/tableanatomy/ This is my guide. They do sell a plan, but my darn Scandinavian frugality convinced me that i didn't need it. Of course, that can always change if it comes out looking like crap. Quote
Popular Post Tom King Posted July 9, 2025 Popular Post Report Posted July 9, 2025 Skip to about 28 minutes in this, and watch the interview with Jim Tolpin. Watch the part where he goes over proportions of a side table and how he arrived at them. This method works without needing to resolve an old puzzle. 4 1 Quote
Ron Swanson Jr. Posted July 9, 2025 Author Report Posted July 9, 2025 On 7/9/2025 at 4:34 PM, Tom King said: Skip to about 28 minutes in this, and watch the interview with Jim Tolpin. Watch the part where he goes over proportions of a side table and how he arrived at them. This method works without needing to resolve an old puzzle. @Tom King Thank you so much! That's one area (design/proportion) that has always been a gray area for me. So i end up duplicating things instead of designing myself. I'll definitely be ordering his book! There's another one i saw recently, i believe called The Principles of Design. Very good stuff in that video, sir! 1 Quote
Popular Post Beechwood Chip Posted July 9, 2025 Popular Post Report Posted July 9, 2025 On 7/9/2025 at 5:34 PM, Tom King said: Watch the part where he goes over proportions of a side table and how he arrived at them. I learned the same thing from a DVD called Unlocking the Secrets of Traditional Design with George Walker from Lie-Nielsen. Long story short, simple integer ratios look good. Everything should be proportional to everything else. 4 Quote
Popular Post wtnhighlander Posted July 9, 2025 Popular Post Report Posted July 9, 2025 Another good principle that Tolpin & Walker espouse, is establishing critical dimensions for your furniture that are based on dimensions of human anatomy (ergonomics). The advantage of making custom pieces is basing them on measurements of the intended individual user(s), rather than a standardized general average. I really like establishing one critical dimension as the master 'unit' of measurement for the piece. All other dimensions can be ratios against that unit, and measure with dividers. No standard rulers, and very little math required! 3 Quote
Popular Post gee-dub Posted July 10, 2025 Popular Post Report Posted July 10, 2025 On 7/9/2025 at 1:51 PM, Ron Swanson Jr. said: Sort of. Really more working off a picture and made some educated guesses at the sizes of the pieces. Funny. Those look sort of familiar. This is a classic form that never seems to go out of date. 7 Quote
Coop Posted July 10, 2025 Report Posted July 10, 2025 I love me some maple accents on walnut furniture. Also maple and cherry. @gee-dub, did you use the wood rail on the sides and groove in the drawers ( I’m sure there’s a rightful name for these?) or mechanical slides/glides? 1 Quote
Popular Post curlyoak Posted July 10, 2025 Popular Post Report Posted July 10, 2025 Here is my version. For the guest room... 6 Quote
Popular Post Tom King Posted July 10, 2025 Popular Post Report Posted July 10, 2025 The book By Hand and Eye is a very good book, but very long winded. You could get what you need to know in a couple of pages. About half of it is in that video. Here is another very good book on proportions, but this one on houses and buildings. Worth the price if you're going to build anything. Dumb title, but good book. https://www.amazon.com/Get-Your-House-Right-Architectural/dp/1402791038/ref=sr_1_1? 3 Quote
gee-dub Posted July 10, 2025 Report Posted July 10, 2025 On 7/9/2025 at 7:46 PM, Coop said: I love me some maple accents on walnut furniture. Also maple and cherry. @gee-dub, did you use the wood rail on the sides and groove in the drawers ( I’m sure there’s a rightful name for these?) or mechanical slides/glides? It is a piston fit. That is there is a partial "box" built into the aprons and the drawer just slides in and out like a piston. The drawers are quite small and light so with a bit of wax rubbed on the surfaces this has worked out well. Build thread here. 1 Quote
gee-dub Posted July 10, 2025 Report Posted July 10, 2025 On 7/10/2025 at 3:59 AM, curlyoak said: Here is my version. For the guest room... Sweet. Love the conch shell decorative item. 1 Quote
Popular Post curlyoak Posted July 10, 2025 Popular Post Report Posted July 10, 2025 On 7/10/2025 at 10:58 AM, gee-dub said: It is a piston fit. For me when I dont use ball bearing slides. I make a bottom mounted u shaped dado channel with a corresponding strip of wood on the bottom center of the drawer. and paraffin wax. The friction is the bottom of the drawer sides. The plywood drawer bottom is in a dado giving 1/2" of space under the drawer to install the guidance pieces of the drawer. Adjustment is easy from the back including a stop. A picture is much easier than words... 4 Quote
Coop Posted July 11, 2025 Report Posted July 11, 2025 So @curlyoak, the bottom of the left and right drawer sides rest on the dust frame and the center strip gives it guidance? Quote
Coop Posted July 11, 2025 Report Posted July 11, 2025 Thanks @Tom King for posting the video. Pretty cool, the whole thing! 1 Quote
Popular Post curlyoak Posted July 11, 2025 Popular Post Report Posted July 11, 2025 On 7/10/2025 at 9:02 PM, Coop said: So @curlyoak, the bottom of the left and right drawer sides rest on the dust frame and the center strip gives it guidance? Exactly. The bottom of the drawer sides must extend down a teeny beyond the bottom of the drawer face to accomplish the bottom reveal. 3 Quote
BillyJack Posted July 11, 2025 Report Posted July 11, 2025 Looks like a table I made in 2000. 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.