Popular Post Ron Swanson Jr. Posted July 13, 2025 Author Popular Post Report Posted July 13, 2025 A little progress. I do my ripping on the bandsaw to get within 1 kerf of my line and then a finishing cut on the table saw. Tapers are marked out on the legs. I need to set them up as they're going to be in the table to make sure the tapers end up where they're supposed to. Learned this one the hard way a while back. All carcase pieces are cut and sized. I left the 2 pieces of the top oversized for now. I'll cut them to final size once they're glued up. And marking the tenons on the 2 sides and back. 5 Quote
Popular Post Ron Swanson Jr. Posted July 20, 2025 Author Popular Post Report Posted July 20, 2025 Halfway done with the mortise and tenons for the sides and back. Wheel gauges are great going across the grain, but not great for end grain. I really need to get more comfortable with a pin style gauge. I find it helpful here to mark the line closest to me going Right to Left, and the back line Left to Right. 5" wide and only 3/4" deep. They came out ok. Shoulder line cuts. I was pretty happy with these. And the tenon, not yet cut to width in this pic. First mortise was a little ugly. I started with the 2 M/T for the back of the table, so any mistake aren't as visible. Second one a little better The third one was much better than the first two. I respect anyone who can chop a clean mortise. The back assembly dry fit. And I'm all out of shop time for the weekend. 5 Quote
Popular Post Ron Swanson Jr. Posted July 22, 2025 Author Popular Post Report Posted July 22, 2025 Mortises 4-6. I can see I need more practice, or a dedicated machine. 6 Quote
Von Posted July 22, 2025 Report Posted July 22, 2025 I think you're doing fine. More consistent than anything I've done. 1 1 Quote
fcschoenthal Posted July 22, 2025 Report Posted July 22, 2025 That's what shoulders are for, hiding any irregularity of the mortise. I would have put one on all four sides the way my mortises turn out. 2 Quote
Ron Swanson Jr. Posted July 22, 2025 Author Report Posted July 22, 2025 On 7/21/2025 at 10:26 PM, fcschoenthal said: That's what shoulders are for, hiding any irregularity of the mortise. I would have put one on all four sides the way my mortises turn out. Very true. You'll only ever see them if they fail! 1 Quote
curlyoak Posted July 22, 2025 Report Posted July 22, 2025 If you can get cherry dowel rod around 3/8" installed through the leg into the tenon. Some object to the end grain. I like it. And it keeps the joint tight for a long time. 1 Quote
Popular Post Ron Swanson Jr. Posted July 23, 2025 Author Popular Post Report Posted July 23, 2025 Got the remaining tenons cut today and the initial fit is promising. I have some fine tuning left to do on 3 of the 6 to get them seated properly, and 1 side isn't quite flush so more fitting to do there. But overall they came out ok. And i picked up a nice dent in one side. I'll have to try and steam it out i guess. Damnit. 5 Quote
fcschoenthal Posted July 24, 2025 Report Posted July 24, 2025 On 7/23/2025 at 5:46 PM, Ron Swanson Jr. said: And i picked up a nice dent in one side. I'll have to try and steam it out i guess. You could always put a bowtie there. Quote
Popular Post Ron Swanson Jr. Posted July 24, 2025 Author Popular Post Report Posted July 24, 2025 On 7/23/2025 at 7:51 PM, fcschoenthal said: You could always put a bowtie there. I was thinking more along the lines of a bumper sticker, but that works too! 3 2 Quote
pkinneb Posted July 30, 2025 Report Posted July 30, 2025 Grab some water, a t-shirt, and an Iron and I bet you can get that out. Quote
Ron Swanson Jr. Posted July 30, 2025 Author Report Posted July 30, 2025 On 7/30/2025 at 2:53 PM, pkinneb said: Grab some water, a t-shirt, and an Iron and I bet you can get that out. That's the plan! 1 Quote
Popular Post Ron Swanson Jr. Posted August 3, 2025 Author Popular Post Report Posted August 3, 2025 Front rails are done. Bottom is a double M/T Top is DT'd. While this is coming along ok, I think I'll probably build another one right after this and try to improve in a few areas. 4 Quote
Mark J Posted August 3, 2025 Report Posted August 3, 2025 I'm impressed you were able to do a double M&T in that slender rail. BTW, are you using mostly hand tools for this project? Quote
Ron Swanson Jr. Posted August 3, 2025 Author Report Posted August 3, 2025 On 8/3/2025 at 10:14 AM, Mark J said: I'm impressed you were able to do a double M&T in that slender rail. BTW, are you using mostly hand tools for this project? Thanks @Mark J . It's about 80/20 hand work. Most of the initial milling was done by machine and the joinery done by hand. I will taper the legs on the table saw when i get there. 1 Quote
Popular Post gee-dub Posted August 3, 2025 Popular Post Report Posted August 3, 2025 This jig has paid off big time for tapering and for straight-line ripping of irregular stock. 3 Quote
Ron Swanson Jr. Posted August 3, 2025 Author Report Posted August 3, 2025 On 8/3/2025 at 2:03 PM, gee-dub said: This jig has paid off big time for tapering and for straight-line ripping of irregular stock. I have Rocklers very similar tapering jig, it has served me very well in the past! 1 Quote
Von Posted August 4, 2025 Report Posted August 4, 2025 On 8/3/2025 at 3:15 PM, Ron Swanson Jr. said: I have Rocklers very similar tapering jig, it has served me very well in the past! +1 Quote
Chet Posted August 4, 2025 Report Posted August 4, 2025 That is some good work so far. Keep it coming. 1 Quote
Popular Post Ron Swanson Jr. Posted August 9, 2025 Author Popular Post Report Posted August 9, 2025 Added taper to the inside faces of the legs. I was taught years ago to either taper the 2 inside faces of a leg, or all 4 faces. So that's what I've always rollled with. Cleaned everything up with a plane And assembly. It's starting to come together. Time to start on the top and drawer and runners/kickers and spacers. 5 Quote
Von Posted August 9, 2025 Report Posted August 9, 2025 Looking good! Nice simple elegant lines emerging. Quote
Ron Swanson Jr. Posted August 9, 2025 Author Report Posted August 9, 2025 On 8/9/2025 at 5:40 PM, Von said: Looking good! Nice simple elegant lines emerging. Thanks @Von! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.