Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Anyone have any tips for a frozen pipe?

Featured Replies

The hot water pipe to my kitchen is frozen and I am having a hell of a time getting it thawed.

 

Most of the pipe runs behind a bank of wall cabinets on an exterior wall. I only have about 10" of exposed pipe, and I can't see where the actual freeze is.

 

I've tried rigging up a cable pipe heater, but the thermostat wouldn't keep the thing on. I then tried a heating pad but there just weren't enough BTUs, now I have a directional shop space heater blasting in the cabinet.

 

Anyone who is used to this sort of thing have any tips short of dismantling my kitchen and opening up the wall?

Is it copper, PEX, something else?  If it was copper, I'd point my propane torch at the exposed piece and figure that since copper is a good conductor of heat, the heat will get to the frozen part.  In the Home Depot plumbing department I got some flexible asbestos mats which I put behind a pipe to prevent other stuff from scorching when I torch the pipe.

 

[ EDIT - don't do this: use a space heater, heat gun, or hair dryer ]

  • Author

It's copper. It's pretty tight (maybe two inches from the rear of the cabinet so I would definitely need to invest in some asbestos.

 

Thanks Chip

I used a hair dryer to thaw a pipe before, but may not work in your situation.

  • Author

The solution was to put the space heater in the cabinet and then come post on WTO.

 

It started flowing within 10 minutes of me posting after dicking around with it for three hours.

 

I was thinking I was going to have to follow chips suggestion and Get Medieval on it.

==> Anyone who is used to this sort of thing have any tips

Yea, wait for spring.. :)

 

Sorry, couldn't resist...

 

If you're not comfortable with a propane torch, use a heat gun. If you don't have a heat gun (and have lot's of time on your hands), use a hair dryer... Hint.. hint... hint, buy yourself a propane torch and/or heat gun...

I think you are probably better off using a slow heat in that area and giving it a night to work.   Keep any downstream taps open, and if there are any in the same branch that are upstream, set one of them to drip.  If you can find the tape type of heater rather than the cable type, they seem to work better for thawing.

 

edit: Just saw your follow up, looks like it did not even need a night.

 

Next time it gets that cold, leave a slow drip open.

Hair dryer. The copper will conduct heat. It usually only takes about 15 minutes to heat the copper so that a trickle will seep around. From there it takes very little time for the water flow to remove the rest of the ice. I've used propane and mapp torches but they tend to heat too fast and boil the water right where you heat it.

I only suggested the propane torch because I thought the heating pad and space heater didn't work.  Glad that you solved the problem with no damage.  I once found several inches of ice on my floor, due to a frozen and burst pipe.  Winter Wonderland in my kitchen - Whoopie!

 

[ EDIT - don't use a propane torch: use a space heater, heat gun, or hair dryer ]

Anyone reading this in the future should avoid direct flame - everything I've read on it says it's not recommended. Last resort type of solution. Slow, even heat is what you want.

+1 on avoiding the use of open flame, if possible.....not for the issue of overheating the water in the pipe, but to avoid starting a fire. Usually once a winter I read a news article about someone who started a fire accidentally by trying to heat frozen pipes with a propane torch.

Glad it all worked out!

Hey Cochese, the plumbers who use flames have attachments for their torches that are like the buddy heaters made for propane grill tanks. In that one circumstance I might try. The heat is diffused and the flame "contained" to a certain degree.

PS, everyone who sweats pipe learns to deal with flames in very awkward places.

Hey Cochese, the plumbers who use flames have attachments for their torches that are like the buddy heaters made for propane grill tanks. In that one circumstance I might try. The heat is diffused and the flame "contained" to a certain degree.

PS, everyone who sweats pipe learns to deal with flames in very awkward places.

 

Yeah, you never know who'll read it and want to try it.

 

Basically you are looking at the possibility of setting a wall or something else on fire, or even melting the solder. Done with caution it might be ok.

I have known welders to hook a truck mounted welder to the valve near the meter box and an outside faucet then barely turn the amps up and thaw a buried line and all the exposed pipes in a crawl space without melting any of the solder.

With all the plastic and lawyers this is probably an outdated technique .....

Even with the heat wide open I couldn't get the shop warm enough to glue up some laminate countertops today. It was 22 outside and the shop was about 52. Label says use above 65 degrees, oh well try again tomorrow. Too damn cold out for my southern blood.

FYI, a house not far from me burned down this morning when the occupants attempted to thaw a pipe with a space heater.

They keys to thawing frozen pipes are patience and vigilance. Preemptive actions like leaving a drip running are the safest bet.

BTW, I live half way between Mason-Dixon and Gulf...it was 1 degree F when I left for work this morning. Bbrrrr...

I have known welders to hook a truck mounted welder to the valve near the meter box and an outside faucet then barely turn the amps up and thaw a buried line and all the exposed pipes in a crawl space without melting any of the solder.

With all the plastic and lawyers this is probably an outdated technique .....

Even with the heat wide open I couldn't get the shop warm enough to glue up some laminate countertops today. It was 22 outside and the shop was about 52. Label says use above 65 degrees, oh well try again tomorrow. Too damn cold out for my southern blood.

-41 degrees Celsius here today. Insane cold.

-41 degrees Celsius here today. Insane cold.

 

Ouch..where was that?  Here in the Ottawa Valley it was only a balmy -21 C..not counting that horrible wind of course.

 

Damn dog still wanted to go for a walk.

i have a simple solution both removes the ice and will open up the cabinet space.........

 

take some gasoline and douse the cabinets.

 

pick up a lighter and set them on fire

 

final use always tasty marshmello's and toast them and enjoy.

i have a simple solution both removes the ice and will open up the cabinet space.........

 

take some gasoline and douse the cabinets.

 

pick up a lighter and set them on fire

 

final use always tasty marshmello's and toast them and enjoy.

 

While you wait for the fire department and your insurance agent 

-41 degrees Celsius here today. Insane cold.

Wow that is hard for me to comprehend ! Did the conversion to Fahrenheit and it's about the same -41.8 F. Don't imagine anyone goes out in that weather willingly.

I went over to Barrie in Ontario to visit family Christmas time a few years back when it was -28 C (-18F) and that was cold enough for me. Can't imagine what -41C (-41F) is like :ph34r: .

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.