jerkface42one Posted January 7, 2015 Report Posted January 7, 2015 Howdy. I'm new to the forum here. So far I've found a ton of great information, so thanks to everyone who is active on here. I've been around woodworking my entire life with my father and grandfather being incredibly active woodworkers. I finally have the time, space, and money to start getting into it seriously myself and just set up my new Sawstop table saw last night. My question is in regard to how anal retentive I should be with the flatness of the table on the saw. The extension wing on the right side of the blade is cupped by about 1/64th of an inch in the middle. The perfectionist part of my brain is telling me I should fix it because dead flatness is sexy, but the realist in me is voicing a loud, "Meh" and saying don't mess with it. Thoughts? How much variation are you normally willing to allow in regard to flatness? Quote
wdwerker Posted January 7, 2015 Report Posted January 7, 2015 I worried about stuff like that when I set my brand new UniSaw up 30 + years ago, I re checked it 10 years ago when I had to replace belts and do a major tune up. Get it as close as possible, within reason, no edges to snag on etc, then move on ! 1 Quote
knotscott Posted January 7, 2015 Report Posted January 7, 2015 Make some test cuts and let them be your guide....if it cuts well, all is well. Quote
wtnhighlander Posted January 7, 2015 Report Posted January 7, 2015 Forget it and move on. Unless the wing protrudes above the main table, it won't make any difference in your cuts. Quote
Tom King Posted January 7, 2015 Report Posted January 7, 2015 You can flex a wing more than you might think. Get one end flush, and tighten that bolt. Next the middle, and then the other end. You should be able to get it flush all the way across. 1 Quote
wdwerker Posted January 7, 2015 Report Posted January 7, 2015 I would be curious what the quality standards were for Sawstop castings (after final milling )especially considering the prices they charge ! 1 Quote
Popular Post Eric. Posted January 7, 2015 Popular Post Report Posted January 7, 2015 What Ross said ^^^...the wings matter not as long as they're low and not high. Your boards reference off of the flatness of your main table. My left wing has a teeny dip in it, too. Doesn't matter. As soon as the new saw smell wears off, you won't care. 3 Quote
..Kev Posted January 7, 2015 Report Posted January 7, 2015 Eric hit the nail on the head.. The wing is not your reference surface so, doesn't matter. Welcome to the forums! Quote
Gary Posted January 7, 2015 Report Posted January 7, 2015 Yep, I would be happy with pretty close. I have an old Crapsman with a cast aluminum main table. It has a hump right down the middle. It is so bad that I have to reset the blade to 90 degrees for cutting on each side of the blade. Very convenient. Quote
jerkface42one Posted January 8, 2015 Author Report Posted January 8, 2015 Thanks for the responses. With your help, the realist won. I'm going to spend my time this evening ripping plywood for the outfeed table instead of messing with it. Which, really.. is going to be a lot more fun. Quote
Tom King Posted January 8, 2015 Report Posted January 8, 2015 It really doesn't take that long, or require that much force, to go ahead and get it flush all the way across. We end up moving table saws several times a year. Only rarely do we have the loader there to take the whole setup from the house to the trailer, so we end up partially disassembling. I do have strong helpers, but I've done it by myself a few times. A helper makes it a lot easier, but the times I've done it by myself, I used a big C-clamp to help with positioning for the last bolt. I just use the blade of a combination square as a guide. I'd get aggravated sliding something across the top of a table saw with an edge to hit from any direction. Quote
Curtis Posted April 10, 2016 Report Posted April 10, 2016 What do you guys think about this one... Similar situation. Brand new SS saw. Eagerly setting it up tonight. Left wing is on, the seam is nut flush, when I put the straight edge running from just the main center table to the edge of the left wing it shows the left wing edge to be high. Can get my .013 Feeler in at the high point. Now if i run from the main table to the edge of the right wing, dead flat, not a hair of light. Part of me says .013, woodworking, not gonna matter? But part of me says, $$$$ new saw, :(, not flat. Should I contact SS or let er slide? Quote
wtnhighlander Posted April 10, 2016 Report Posted April 10, 2016 Quit worrying and make something! Wings are just there to hold your beverage if choice, anyway. The main table is far more important. 1 Quote
Brendon_t Posted April 10, 2016 Report Posted April 10, 2016 36 minutes ago, wtnhighlander said: Quit worrying and make something! Wings are just there to hold your beverage if choice, anyway. The main table is far more important. If someone puts a beverage on my cast iron wings that are 20 years old and scratched to hell, I'd smack them with a push stick. Last thing I need is their rust spots interfering with my 12oz can sized rust spots. Quote
Tpt life Posted April 10, 2016 Report Posted April 10, 2016 Any part of the wing high is bad in my experience. A touch low is better. You always want your work tight to the table where it is being cut. I would work to get the butt flush and the outer edge in plane with a hollow in between if the wing is dished. This usually involves some back and forth with blue tape shims. 1 Quote
knotscott Posted April 10, 2016 Report Posted April 10, 2016 11 hours ago, Curtis said: What do you guys think about this one... Similar situation. ... ...Part of me says .013, woodworking, not gonna matter? But part of me says, $$$$ new saw, :(, not flat. Should I contact SS or let er slide? It could very well be a non-issue. Don't contact SS unless the flatness is effecting the cut. If you're results are off due to table flatness, you've got a very strong beef. Otherwise, it's just nitpicking for the sake of nitpicking. Replacing the top simply because you paid a lot for it, just means others will pay more for it. $$$$$ 1 Quote
gee-dub Posted April 10, 2016 Report Posted April 10, 2016 On 1/6/2015 at 5:02 AM, Tom King said: You can flex a wing more than you might think. Get one end flush, and tighten that bolt. Next the middle, and then the other end. You should be able to get it flush all the way across. +1 on this. Cast iron is quite malleable. This will get you a flush seam. To obtain flat from left to right you can manipulate the fence rail attachment points a bit. Now, the glossy black right side table extension is another issue. Poor design and execution and the low point of the saw IMHO. I still have to go back and provide a more permanent fix. Quote
gee-dub Posted April 10, 2016 Report Posted April 10, 2016 3 minutes ago, Mike. said: ???? What glossy black right side Sorry, I assumed a 3HP PCS. Oh silly me ;-) What model is it? Or maybe the PCS doesn't come with the glossy black table anymore? Depending on the fence option the comment about using the fence rails to help with the wing could be off base too. Boy, I need to not reply until the coffee kicks in. Sorry about that. Quote
gee-dub Posted April 10, 2016 Report Posted April 10, 2016 It is not the color; that's kinda cool. Mine is framed with soft pine underneath. Despite the rather cool leveling pin in the middle of the CI wing seam, the attachment points at the fence rails are used to additionally align this table. The pine is so soft that the alignment will not hold. I added large fender washers to try to increase the pressure area and supply enough grip but, it still eventually fails. There are holes in the CI wing that I will try to work something out with next effort. Its not too terrible. It is just such a contrast with the high quality level of everything else about the product that makes it a head scratcher. ;-) Quote
knotscott Posted April 13, 2016 Report Posted April 13, 2016 So where does the OP stand with the table top? Quote
Curtis Posted April 14, 2016 Report Posted April 14, 2016 On 4/13/2016 at 10:05 PM, knotscott said: So where does the OP stand with the table top? Funny thing happened. Went to attach front rail to the ext wing and the stupid holes on the extension wing don't line up (the other wing lines up just fine). So Im waiting again for a new wing to arrive. I also didn't realize I can flex them a bit and when I attach to the rail it helps level things out. I was just gonna go with it, tired of waiting, but oh well. When my 'first' saw arrived the fence/rail package had been destroyed by a forklift, ridiculous they even tried to hand it to me with a straight face. And they had to replace/send an entire saw! And now waiting for this silly wing. Quote
Chestnut Posted April 14, 2016 Report Posted April 14, 2016 8 hours ago, Curtis said: Funny thing happened. Went to attach front rail to the ext wing and the stupid holes on the extension wing don't line up (the other wing lines up just fine). So Im waiting again for a new wing to arrive. I also didn't realize I can flex them a bit and when I attach to the rail it helps level things out. I was just gonna go with it, tired of waiting, but oh well. When my 'first' saw arrived the fence/rail package had been destroyed by a forklift, ridiculous they even tried to hand it to me with a straight face. And they had to replace/send an entire saw! And now waiting for this silly wing. Hey at least it's nothing you've done to yourself. Hope you get your new wing soon and get yourself up and running. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.