Recommended Posts

Posted

I would like to post a question to the class. Is snipe on a planer and drum sander just the cost of doing business or is it the result of incorrect calibration/ bad setup?

If you believe it can be helped, What types of fixes have you found that either reduce or eliminate snipe?

I have recently become aware ( by an overflowing milk crate) of just how much wood I lose to cutting off snipe ridden ends.

Posted

Probably just a result of expecting the machine to do all the work.   I still have the first model Delta lunchbox planer that we use once in a while on jobsites.  It has the worst reputation ever for snipe.  The last time we used it, it was used to run a bunch of Yellow Pine 2x12x16s just to clean them up for use in a boathouse.  We got no snipe at all on these boards.  With a board that heavy, and a planer known for snipe, the board has to be held up to the point that it lifts the front of the planer up, and the reverse as it comes out the other end.  On better quality planers, it doesn't require that much effort, but operator hands still play a part.

Posted

Properly supporting the wood beyond the little tables helps me a bunch..  Like you, I leave pieces long for this reason and end up with the same small chunks without snipe..  They come in handy at some point ;)

Posted

Death, Taxes and Snipe...

 

You can address snipe, but it'll cost you... For about $10K, you can get yourself a nice little 15" planer: http://www.felderusa.com/us-us/products/planers/planer-d-951--504-mm.html-- if you want Tersa, add about $4K... Now for about $18K, you can get a 20" planer, Tersa included: http://www.felderusa.com/us-us/products/planers/planer-d-963--630-mm.html ... :)

 

At the end of the day, loosing a couple of inches from each board is less expensive than your time... You can use the off-cuts for finish test pieces, setup blocks, glue blocks, whatever...

 

If you feed stock one after another like a train, snipe will be reduced for the sticks in the middle (I learned that one in Frank Klausz's shop many years ago)...

 

That's about all you can do...

Posted

Probably just a result of expecting the machine to do all the work. I still have the first model Delta lunchbox planer that we use once in a while on jobsites. It has the worst reputation ever for snipe. The last time we used it, it was used to run a bunch of Yellow Pine 2x12x16s just to clean them up for use in a boathouse. We got no snipe at all on these boards. With a board that heavy, and a planer known for snipe, the board has to be held up to the point that it lifts the front of the planer up, and the reverse as it comes out the other end. On better quality planers, it doesn't require that much effort, but operator hands still play a part.

sorry, I must have forgotten typing that I expected my machine to do all of my work for me.

Good info class. . And i liked mw's video. I too have a delta box that actually measures 12 thousandths thinner at the end.

I'm starting to doodle a project plan and a cutlist for an end table but will be made with walnut and a really cool piece of figured maple I bought yesterday.I have just barely enough yield from this one board to create all of the Maple pieces I need with almost no waste.

Hey triple h, is it too late to put that wifi enabled sandwich making 18k unit on my xmas list?

Posted

Seriously, guiding hands can eliminate it.   We had a job with a few hundred pieces to run, that needed to be precisely thicknessed.  The lunchbox wasn't even considered.  The big Powermatic wouldn't mic them all the same, but the Grizzly planer/molder did. Even then, I had to use some feel in feeding the machine, and taking it out the back.   I do have helpers, so I didn't have to dance back and forth. I fed, and best helper handled the outfeed.   We've done it enough, that it's second nature.   Any of them will produce snipe if I just hand the machine a board, and let it spit it out the back.

 

For valuable short boards, run some sacrifice boards in runs before the final run to finished thickness, and use one of them to be the starter pushed in by the first good piece, and end with a push from another sacrifice piece.

Posted

My Dewalt 735 snipes only a very minor amount - enough to easily sand out with a ROS.

+1 on this. Compared to many benchtop planers, the 735 appears to have a wider support platform under the rollers. I have almost no snipe, unless I am planing parts longer than 4 feet or so and don't support the ends.
Posted

Yes in my opinion snipe is inevitable. Cut the boards longer at either end and clip the snipe off when you have finished thicknessing. When you have enough glue the pieces together and make a reindeer.

If you have limited stock length remove the snipe bulge with a handplane.

Posted

I would like to post a question to the class. Is snipe on a planer and drum sander just the cost of doing business or is it the result of incorrect calibration/ bad setup?

If you believe it can be helped, What types of fixes have you found that either reduce or eliminate snipe?

I have recently become aware ( by an overflowing milk crate) of just how much wood I lose to cutting off snipe ridden ends.

 

With some planers you can reduce snipe or nearly eliminate. Would help to know what planer you have. Snipe with the drum sand should not happen.

Posted

Good catch on the drum sander, i missed-that... The only time I've seen sander-snipe is feeding stock that's near the minimum length spec for the unit... I always add several inches to the minimum...

Posted

I have a 735, and its probably the best bench-top you can get. I will eventually upgrade, but it will be to a 20" so that I get the added features that a lot of 15" models don't have.

 

 

try one or two of these, and see if they hep you reduce snipe.

 

1. assuming you have a machine with adjustable wings, adjust them so the outer ends  are 1/32" to 3/32" above the bed. For short boards this is just like the operator lifting up on the trailing edge.

2. if the work piece allows, feed the board through at a slight angle. I'm at a loss to explain why this works, but it always helped to reduce snipe.

3. for longer boards, use in-feed and out-feed roller stand just like in #1, just raise them higher.

Posted

A melamine table board and wax. If your doing a large run of the same boards use a rabbet carrier also works if you are getting tear out on woods like curly maple but requires a rabbet edge on every board.

 

 

 

 

Posted

I do a lot in red oak and a little snipe is a by-product that provides a small amount of little chunks of scrape that I use to start the fire in my off set smoker.  So all is not bad.  Although I am hoping this will diminish in the future when I get my DW 735 in a day or two.

Posted

Start with a sacrificial piece, run all work pieces continuously end to end, end with sacrificial piece. Rarely did I ever have snipe on my work.

 

It can be done, and if you do it enough it will become second nature.

  • Like 1
Posted

I usually do what Sam just said run them butt to butt. I learned to trim all the ends just enough to square them up and the lead scrap can be anything that's a similar thickness.

For my lunchbox planer I built an 8 ft infeed and outfeed box the height of the planer off the table. I clamp my planer in the middle of my 12 ft table and the boxes hang off each end. It's easier with 2 people but you can run back and forth and do it yourself if you have to.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 45 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined