eball Posted April 30, 2015 Report Posted April 30, 2015 Hey guys, Im in a bit of a loss. My TS fence is parallel with the blade and the miter slot. My problem is setting the fence to the ruler tape. I zero out the fence to the blade, then adjust my red line indicator over the zero on the ruler strip. But the farther I get away from zero, the more 'off' the measurement is. I've tried multiple times, dialing in the red line indicator at various distances, but it doesn't stay accurate the farther i get from my start point. I hate having to always use a measuring tape not being able to rely on my fence tape. Has anyone else dealt with this and know what I'm doing wrong??? Quote
Guest Posted April 30, 2015 Report Posted April 30, 2015 compare your tape measure to the ruler on your fence rail. do they match up? Quote
Eric. Posted April 30, 2015 Report Posted April 30, 2015 ^^^ The only explanation...one of them is off. Quote
Janello Posted April 30, 2015 Report Posted April 30, 2015 I usually cut a piece of stock and mic it with calipers until I get a nice even number, then set the red line. It's hard to know if the fence is right on the tooth perfectly doing it your way. 1 Quote
Tom Cancelleri Posted April 30, 2015 Report Posted April 30, 2015 What Janello said. I do that, then adjust the red line indicator with a dial indicator. Quote
..Kev Posted April 30, 2015 Report Posted April 30, 2015 Even though I know my ruler is on, I don't trust it. I still measure blade to fence to be sure. Quote
Janello Posted May 1, 2015 Report Posted May 1, 2015 Even though I know my ruler is on, I don't trust it. I still measure blade to fence to be sure. I think this depends on the operation. I was putting up siding in the shop, and could care less if I was 1/16th off and it sure was handy to not have to break out a rule. But I agree, not exactly a scientific measuring device they stick on there. actually, I'm usually just using the mark on my stock to line up my cut....the built in tape gets me close before a final adjustment. Quote
Stobes21 Posted May 1, 2015 Report Posted May 1, 2015 Is it possible your fence rails are a little loose? Especially if you move it around a couple of loose bolts can let the fence rails move slightly and throw off your measurements. Quote
Tpt life Posted May 1, 2015 Report Posted May 1, 2015 All the suggestions have some merit, but the first posts had it. The key is wider variation at further distance. Loose parts would give slop and lead to unpredictable results. The scale of the fence tape is suspect. Possibly the tape got stretched. This would lead to an increasing error the further away from zero. 1 Quote
Coop Posted May 1, 2015 Report Posted May 1, 2015 I don't know that I ever used the scale on the fence as a measurement. I have a pretty accurate 24" metal ruler that I use to set the distance between the blade and the fence. Then, after cutting a trial piece if it's absolutely critical, I'll use the scale to "bump" it over a bit. If I take my glasses off, it's usually pretty close! Quote
Tom Cancelleri Posted May 1, 2015 Report Posted May 1, 2015 I calibrate my fence before every project that will include a lot of tablesaw action. I trust my ruler 100% bought a new starret metal scale for the saw. Quote
Eric. Posted May 1, 2015 Report Posted May 1, 2015 It's funny...my saw scale is dead nuts on and always has been...but every time I go to make an important cut, I check it with a tape or rule. And it's always right. But I keep checking. I don't know what it has to do to earn my trust. 2 Quote
Popular Post Freddie Posted May 1, 2015 Popular Post Report Posted May 1, 2015 I never installed the tape on my table saw. That's how I feel about that. 3 Quote
wtnhighlander Posted May 1, 2015 Report Posted May 1, 2015 I slid my rails as far right as they would go, and never bothered to replace the tape. Quote
Brendon_t Posted May 1, 2015 Report Posted May 1, 2015 It's funny...my saw scale is dead nuts on and always has been...but every time I go to make an important cut, I check it with a tape or rule. And it's always right. But I keep checking. I don't know what it has to do to earn my trust. Once you figure it out, let me know. I do the same thing. Quote
ColinF Posted May 1, 2015 Report Posted May 1, 2015 I have never even thought about using it, I've got a 16" metal rule that I use, for anything bigger than that I just break out the tape measure. Quote
Twistedcowboy Posted May 1, 2015 Report Posted May 1, 2015 I'm making a crosscut sled currently. I have to use a square every time I set my fence to make sure it is set right. Kind of frustrating. Quote
dwacker Posted May 1, 2015 Report Posted May 1, 2015 Your fence tape is probably closer than you think. Unless you are standing directly in front of the reticle looking straight down in the same position every time your reading will change. The further away you get from the blade the more you tend to look at it from an angle. Bottom line don't use it for final adjustment just use it to get semi close and use a steel ruler. Quote
Chet Posted May 1, 2015 Report Posted May 1, 2015 It's funny...my saw scale is dead nuts on and always has been...but every time I go to make an important cut, I check it with a tape or rule. And it's always right. But I keep checking. I don't know what it has to do to earn my trust. Me too. Quote
Shane Jimerfield Posted May 1, 2015 Report Posted May 1, 2015 I never installed the tape on my table saw. That's how I feel about that. I did, but it's only for rough dimensioning. Quote
wdwerker Posted May 3, 2015 Report Posted May 3, 2015 Starrett tape is more accurately printed. I added a digital scale and it's great for tweaking to tiny measurements, push a button and use metric too ! I still double check with a tape frequently. As soon as you drop a new tape the hook can get bent even slightly and your measurements will be off. I take the hook off and keep my tape in my pocket. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.