Popular Post wtnhighlander Posted March 2, 2016 Popular Post Report Posted March 2, 2016 ... for a new chess board. So, my wife and son like to play chess together, but were getting tired of the worn-out old cardboard playing field they had. Wife says "Why don't you make us a new board?" So I had a good way to use up some scraps from the bin. I first resawed some maple and walnut to make the squares. My little bandsaw isn't great, so I make a kerf on the table saw first. Honestly, I could just as effectively have finished these off by hand. I was cutting it close on the maple, having just enough to make do. Plenty of walnut scraps, though! Here are the boards, jointed and planed. Since there wasn't much wood to spare, I was careful to get the end squared up prior to glueing, rather than taking a chance on having to trim both ends, and waste too much. Sorry for the blur. With the blue tape behind the seams, I just folded each seam over the edge of the bench to apply glue with an acid brush. After the glue dried, and I scraped off the squeeze-out, I cross-cut and flipped every other piece to create the pattern of squares. Mistake #1 - I used a piece of 1/4" luan plywood as a substrate for the hardwood squares. Mistake will be obvious in a moment. For now, how do you like my Redneck veneer press? Initial clean up of the surface involved a paint scraper, and this little jewel ... Here is what it looks like after a rough sanding. Indoor incandescent lighting, really warms the color in photographs. And NOW you see the problem. Maybe it was moisture in the glue, I dunno. The hardwood and ply had both been 'acclimating' in my shop for almost two years. So, after getting some advise from Steve and others here (Thanks to all). I make a 3/4" thick panel of poplar, and glued the board to it. This gave the thing enough stiffness to remain flat. I left it longer and wider than the board. because I wasn't yet sure how I would trim it out. Back to the bandsaw to rip down some of the remaining maple for edge banding. This blade drifts badly, too much to manage with a full fence. I do better by marking the cut line, and just using the combo square head as a visual reference to keep this little piece square to the table & blade. Time to bust out Gandpa's old #4 to smooth out the resulting banding. Just using tape works pretty well to hold the glue in place for the banding. I use as much blue tape in most projects as I use glue. Closeups of the corner details. I did have one square that started to de-laminate on me. I masked it off, and used a bamboo skewer to work some TBIII into the crack. Seems to have worked, I hope it holds! That's about it for now. I have to come up with a frame of some sort to go around the edge. I have a little bit of cherry that may wind up as a 'diploma' style frame around this board. One thing I forgot to photo - I used the router table milling technique I described in another thread to remove 1/4" of thickness from the bottom of the poplar base panel, just to eliminate the excess bulk. More to come soon. if the weather co-operates! 8 Quote
Chestnut Posted March 2, 2016 Report Posted March 2, 2016 Looking good. I really like the edge detail. Are you going to make a box underneath of it for storage of the pieces that you carve by hand? Quote
N00b-in-training Posted March 3, 2016 Report Posted March 3, 2016 Looking great! Glad the kids aren't looking over my shoulder right now or this would get added to the list quick! Quote
wtnhighlander Posted March 3, 2016 Author Report Posted March 3, 2016 Looking good. I really like the edge detail. Are you going to make a box underneath of it for storage of the pieces that you carve by hand? Hand-carved pieces have been vetoed by the woman in charge, she wants a TV stand / storage unit made for the spare bedroom. Quote
wtnhighlander Posted March 8, 2016 Author Report Posted March 8, 2016 A brief update. Now that the board is flat, and seems stable, I started working on a decorative frame to cover the edges. I had just enough cherry stock on hand to saw out some sticks about 1" square. Rather than make a ton of noise with the DW735, and risk tearout, I hand planed them in a gang to get the size exact, and remove burn marks from the saw. I also needed to reduce the thickness of the poplar backer board, by about 3/16". This cheap plane from Harbor Freight does a surprisingly good job as a scrubber. I finished leveling with my #4C Stanly clone. Here is the profile for the frame molding. A lip on the bottom to hold the board, and an 8* bevel on the outside. Simple as can be. More to come soon, if the warm weather holds out. 2 Quote
shaneymack Posted March 8, 2016 Report Posted March 8, 2016 Missed this when you originally posted the other day. It looks great Ross. Im not sure im understanding that decorative piece you just made. Are you covering the nice decorative edges that you already glued on? Quote
wtnhighlander Posted March 8, 2016 Author Report Posted March 8, 2016 Missed this when you originally posted the other day. It looks great Ross. Im not sure im understanding that decorative piece you just made. Are you covering the nice decorative edges that you already glued on? Not the show face. Covering the sides where the laminated edge shows. Quote
Popular Post wtnhighlander Posted March 9, 2016 Author Popular Post Report Posted March 9, 2016 Got a little more done today. This cardboard will become the core of the cushioned base of the board. Here I am covering it with black velour upholstery fabric. Bottom of the board, sanded and branded. Note the recess into which the cardboard base will fit. And here is the first coat of spray lacquer. I debated using danish oil, which would have been smooth an sexy, but opted for durability instead. Still undecided about leaving it glossy, or buffing it to a matt finish. I plan to have it ready to play in the morning. Hopefully I can get lighting for some good in-situ photos for the showcase. Thanks for following along! 10 Quote
Chestnut Posted March 9, 2016 Report Posted March 9, 2016 Wow that is awesome! I really really really like the boarder detail around the edge. Was it hard to do? 1 Quote
Coop Posted March 9, 2016 Report Posted March 9, 2016 Play in the morning? Dang, don't any of you guys have a real job?? Great looking board Ross! I too like the boarder. 1 Quote
Chet Posted March 9, 2016 Report Posted March 9, 2016 That is real nice Ross. Probably a good decision on the finish what with soda, coffee and or beer being spilled or thrown in the wheat of battle. Chess can be a vicious game. 1 Quote
shaneymack Posted March 9, 2016 Report Posted March 9, 2016 Ross that turned out awesome man. Nice work! Sent from my SM-N910W8 using Tapatalk 1 Quote
wtnhighlander Posted March 9, 2016 Author Report Posted March 9, 2016 Wow that is awesome! I really really really like the boarder detail around the edge. Was it hard to do? Not hard, just tedious. Making the banding a little wide, then planing / sanding it flush after glue up helps a lot. Play in the morning? Dang, don't any of you guys have a real job?? Great looking board Ross! I too like the boarder. Uh, yes. I won't be the one playing... Last-minute update: I have several coats of lacquer in it now. Gloss really does look like plastic. A glassy-smooth french polish might look good, but this ain't that. Anyone have a favorite technique for buffing the gloss down a bit? Quote
wdwerker Posted March 9, 2016 Report Posted March 9, 2016 I buff with a gray abrasive pad then come back with a white one. Make sure the lacquer is completely dry and hard or you will smudge the finish. Quote
wtnhighlander Posted March 9, 2016 Author Report Posted March 9, 2016 I buff with a gray abrasive pad then come back with a white one. Make sure the lacquer is completely dry and hard or you will smudge the finish. Think overnight is enough dry time? Quote
wdwerker Posted March 9, 2016 Report Posted March 9, 2016 Thin coats from a rattle can ? When you can't smell even a faint trace of solvent give it another full day before you try buffing. Too soon is risky . Quote
wtnhighlander Posted March 9, 2016 Author Report Posted March 9, 2016 While its on my mind, here is a shot to illustrate how I peel the backing from double-stick tape. This question came up a while back, generating quite a discussion. I slice a diagonal line across the backing, and use the knife point to lift the sharp corners. This avoids pulling up the tape, as will often happen when peeling from the end. Ok, I rushed the finish a bit, butI promised to have it ready to play this morning, so here it is. I'm lucky lacquer dries so fast! I'll post some better photos in the showcase, as soon as I get the light too make them. 1 Quote
SawDustB Posted March 11, 2016 Report Posted March 11, 2016 That looks great! I'm curious, how did you avoid movement issues with having the solid frame? Is it OK because your surface is thin enough to be treated like veneer? Quote
wtnhighlander Posted March 11, 2016 Author Report Posted March 11, 2016 That looks great! I'm curious, how did you avoid movement issues with having the solid frame? Is it OK because your surface is thin enough to be treated like veneer? Only time will tell if I've avoided movement! The three layer construction seems (so far) to behave like plywood. I'm counting on that to keep it balanced. Check back after its been through a year of West TN humidity swings! ? 1 Quote
Brendon_t Posted March 11, 2016 Report Posted March 11, 2016 Ross, I'm a bit lost as to where the fabric covered cardboard went.is it under the board sitting on the table? 1 Quote
wtnhighlander Posted March 11, 2016 Author Report Posted March 11, 2016 Ross, I'm a bit lost as to where the fabric covered cardboard went.is it under the board sitting on the table? Yep. Note the shadow line under the bottom. Keeps the wood from scratching the table. Table is one of mine, too. I call it a 'modern rustique' in walnut. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.