Recommended Posts

Posted

I just tripped the brake on my SawStop, ruining the cartridge, of course, but also the blade. I was cutting a board with some graphite fabric glued to it. The blade has 1 tooth & the steel behind it torn off & another partly removed. I'll not do that again.

Not much drama though, just a thunk & then silence.

SS cartridge.jpg

Posted
7 minutes ago, Chestnut said:

That stinks :( Did you at least have a backup cartridge so your not stranded?

Ya, I've got a spare cartridge, rip & crosscut blades, but that was my only combo, & it was really good.

Does anyone have an opinion on the Freud Premier Fusion 40T combo? It's on sale for a good price at KMS.

Posted

I've seen two of those go off, it is just a thunk as you said, not much noise at all. this was at my part-time job and two different guys set it off, needless to say they have extra cartridges handy all the time.

Posted
7 minutes ago, mat60 said:

That stinks. Hope it didn't cost you to much.

Cartridge is $98, the blade was about $100. I'm bothered more by my mental lapse than I am about the $200 though.

11 minutes ago, Chestnut said:

I have a freud industrial 50T combo and it works pretty good for cross cuts but struggles on rips thicker then 1" I think that's more the 50T and less the blade.

Ya, 50T is a bit much for ripping I think.

11 minutes ago, treeslayer said:

I've seen two of those go off, it is just a thunk as you said, not much noise at all. this was at my part-time job and two different guys set it off, needless to say they have extra cartridges handy all the time.

I would have expected much more. The saw didn't even flinch of vibrate.

Posted
Just now, Brendon_t said:

Does it release the belts when it trips? I can't think it could stop the motor dead in its track like it does the blade.

The brake engages the blade & the blade drops, but I don't know if the drive disengages as well. It must, to be able to stop so fast. there is a lot of rotating mass in the motor.

Just now, Woodenskye said:

Guess you need a new blade, a new brake and some new underwear.

No new underwear required. As I said earlier, no drama at all.

Posted

If it makes you feel any better, the other day I was cutting some pressure treated wood for the deck I've been building on my sawstop and, while I remembered to turn off the brake, I forgot to clean off the sawdust after I was done. My cartridge is in tact, but my table top is now covered in rust. Definitely a lot cheaper of a fix than your situation, but I did feel like an idiot afterwards.

Sent from my iPad using Tapatalk

Posted

Nah.You're not a complete idiot.

Complete idiocy would require you to put in a new blade and cartridge, and then try to run the graphite fabric through again.;)

Posted
Ya, I've got a spare cartridge, rip & crosscut blades, but that was my only combo, & it was really good.

Does anyone have an opinion on the Freud Premier Fusion 40T combo? It's on sale for a good price at KMS.

I have a full kerf fusion. No complaints.

Sent from my SM-N910W8 using Tapatalk

Posted
41 minutes ago, davewyo said:

Nah.You're not a complete idiot.

Complete idiocy would require you to put in a new blade and cartridge, and then try to run the graphite fabric through again.;)

You haven't given me a chance to put a new blade in yet :(

 

  • Like 2
Posted

Been there.  I cut some UHMW material that I discovered was anti-static treated.  My test device was my Saw Stop :angry:.  I hung the cartridge and the blade on the wall as a reminder.

Posted
19 minutes ago, gee-dub said:

Been there.  I cut some UHMW material that I discovered was anti-static treated.  My test device was my Saw Stop :angry:.  I hung the cartridge and the blade on the wall as a reminder.

I think I'll hang the old cartridge right beside the switch.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 63 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined