Nestor Posted December 23, 2016 Report Posted December 23, 2016 Okay, last Xmas project... Purchased the CMT Bowl & Tray bit and collet extension last year. Time to finally put it to use. Like turning, different species can be glued together for effect. The advantage of the B&T bit is the ability to make "unturnable" shapes. I chose a pill-shape for the wood I had on hand and for the fact my bandsaw can't resaw anything wider than 6". PSA. When buying a bandsaw, get the riser blocks and a couple of blades, even if you don't think you need them. You'll thank yourself later. Final choice: white oak and wedge. Resawed... I left the edges unjointed. It will be trimmed away with the bandsaw later. The outside width of the bowl will be 5" and I will only have 6" to work with, so no room for error when laying down the template. Glue-up. It's a shame much of the wenge will be turned into chips. It's a nice grain. Next up, mdf template. Stay tuned. Sent from my iPad using Tapatalk 1 Quote
Sac Posted December 23, 2016 Report Posted December 23, 2016 Gonna look good. And I will stay tuned. Quote
treeslayer Posted December 23, 2016 Report Posted December 23, 2016 i'm gonna ride along on this one too Nestor, looks interesting Quote
Nestor Posted December 23, 2016 Author Report Posted December 23, 2016 The bit and extension... Sent from my iPad using Tapatalk Quote
wdwerker Posted December 23, 2016 Report Posted December 23, 2016 I have gotten good results with CMT bits. Be careful with that extension. Don't take to much depth in one pass. If your router is older the affect of worn bearings will be amplified by the extension. I am egaer to see how your bowl turns out ! Quote
Chet Posted December 23, 2016 Report Posted December 23, 2016 40 minutes ago, wdwerker said: worn bearings will be amplified by the extension. Good point. Good luck Nestor. This would be a fun one for video. Quote
Brendon_t Posted December 24, 2016 Report Posted December 24, 2016 Looking forward to seeing it move forward. If you haven't worked wenge, you haven't lived. Quote
wtnhighlander Posted December 24, 2016 Report Posted December 24, 2016 Looking forward to this as well. I'm curious how well the collet extension works. Quote
Nestor Posted December 24, 2016 Author Report Posted December 24, 2016 Update: Unless your bowl is 2" diameter, chances are you will need a bigger base. For want of 3/8" plastic (small town blues) I laminated two pieces of 1/4" hardboard. Template time... As mentioned, I don't have much width to work with so centering the template across was crucial. One could easily begin routing at this point, but it's quieter, somewhat safer, and far less dusty to hog out as much as you can at the drill press with a forstner bit. Some important considerations while at the drill press. 1. Forstners leave dimples. Unless you want your bowl to look like a golf ball, you need to account for this when setting the depth of your drill press. 2. Keep way from the template for two reasons. First, the B&T may follow the gouge if it's anything bigger than a hair. Second, you may end up leaving a squared-off bottom that can't be rounded out by the B&T bit. 3. Keep your work secure and empty out the chips often. See #2. Hogged out. Had a close call when I tried to drill out a small area and the forstner bit jumped away. Ready to rout. I secured the blank with carpet tape on plywood. I really need to build that bench top soon. I used the stepped depth stops on my plunge base to take off small amounts each pass. Half ways done. For the deepest pass, I had to loosen off the collet and collet extension to get a little more length. Success! Seems I uncovered something I did "knot" see. Is it okay to leave it, or should I fill it? Next up, bandsaw. Sent from my iPad using Tapatalk 2 Quote
Sac Posted December 24, 2016 Report Posted December 24, 2016 Id fill it with a little CA glue. Will keep things from going in there (Food or dip or dressing whatever.) Should fill pretty easily, and should look just fine. Looks good! 2 Quote
Nestor Posted December 24, 2016 Author Report Posted December 24, 2016 Time to sand... Sent from my iPad using Tapatalk 1 Quote
Isaac Posted December 24, 2016 Report Posted December 24, 2016 Interesting shape, what do you envision it being used for? Quote
wdwerker Posted December 24, 2016 Report Posted December 24, 2016 My guess is keys , wallet, gloves etc. Quote
Chet Posted December 24, 2016 Report Posted December 24, 2016 Spare change... Nice work Nestor. Quote
Nestor Posted December 24, 2016 Author Report Posted December 24, 2016 Sanding sanding sanding Sent from my iPhone using Tapatalk Quote
Nestor Posted December 24, 2016 Author Report Posted December 24, 2016 Back to the router finish the base and top. 1/2" 4-cutter round-over to mitigate tear-out... And a 1/8" round-over for the top. Wenge. I worked with it before to make the ribbon-handle boxes and didn't find it hard to work with. Not this time. Sent from my iPad using Tapatalk Quote
Popular Post Nestor Posted December 24, 2016 Author Popular Post Report Posted December 24, 2016 Coat of tung oil... Fin This elf needs a rest! Thanks for following. Sent from my iPad using Tapatalk 5 Quote
Keggers Posted December 24, 2016 Report Posted December 24, 2016 Excellent job! I did a similar project in the shape of a snowman for my wife to hold candy. It's not a pretty as yours! Quote
Nestor Posted December 27, 2016 Author Report Posted December 27, 2016 Thanks for the compliments everyone! Sent from my iPhone using Tapatalk Quote
pkinneb Posted December 27, 2016 Report Posted December 27, 2016 Very nice! I like the shape you used on the bottom! Quote
Ronn W Posted December 28, 2016 Report Posted December 28, 2016 Nicely done. Seems like some of the process were real nail-biters. I like it. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.