Andy Faust Posted January 16, 2017 Report Posted January 16, 2017 Hey I have the same planer and am looking in to a cheep way do get adequate dust collection from it. What do you think of the drunken woodworking perch at make something. Looks like the bag is running about $40 on Amazon. Quote
mat60 Posted January 16, 2017 Report Posted January 16, 2017 Hi Andy. Im not saying it wont work ok but the bag will fill up fast depending on how much you do and it seems in the way. His wood drags on his bag if you dont hold it up also. Quote
Popular Post Llama Posted January 16, 2017 Popular Post Report Posted January 16, 2017 5 minutes ago, mat60 said: His wood drags on his bag if you dont hold it up also. Story of my life! 9 Quote
Llama Posted January 16, 2017 Report Posted January 16, 2017 2 minutes ago, Mike. said: Wouldnt a pillowcase and twine be cheaper? Yeah, where is Clifford? Quote
Coop Posted January 16, 2017 Report Posted January 16, 2017 I purchased Rockler's 4" x 10' hose last week and plan to make a bag from a bed sheet. This will get the bag out of the way of the outfeed and keep me from having to empty my dc bag as often. 1 Quote
wdwerker Posted January 16, 2017 Report Posted January 16, 2017 Depending on the bed sheet some coarser fabric might work better. Planer shavings usually don't have all the fine dust a saw produces. Quote
RichardA Posted January 16, 2017 Report Posted January 16, 2017 Remember, that planer throws the chips very hard, if it grabs a knot, you might kiss your bag goodbye. There's always this. Quote
Llama Posted January 16, 2017 Report Posted January 16, 2017 Just now, Lester Burnham said: I thought that was Collin? Clifford uses a pillowcase, Collin uses twine. Quote
Chet Posted January 16, 2017 Report Posted January 16, 2017 Andy If you go that route I think what Coop is doing would be better then have the dust bag laying across the outside. Quote
Andy Faust Posted January 16, 2017 Author Report Posted January 16, 2017 Hey thankseveryone looking for something that is also safe. Not sure how a pillowcase be at adequately holding in the finer dust. I don't plan on using a dust mask or a respirator. Quote
Brendon_t Posted January 16, 2017 Report Posted January 16, 2017 Rockler sells a dust rite 30 micron bag with a zipper to empty. I have seen 4" hard pipe used to direct it over to the root of the table then down where the bag will connect and blow down. No interference with the table. Quote
Tpt life Posted January 16, 2017 Report Posted January 16, 2017 Just noodling here... Do you think the blower is strong enough to drive a small cyclonic action without the need of an impeller if the pipe were only two or three feet long? Quote
Andy Faust Posted January 16, 2017 Author Report Posted January 16, 2017 I'm not sure if it's strong enough for a standalone cyclone I really haven't gotten much use on. It but if it is that would be a good idea. Any suggestions on a good cyclone. Quote
Chet Posted January 16, 2017 Report Posted January 16, 2017 1 hour ago, Andy Faust said: Not sure how a pillowcase be at adequately holding in the finer dust. You don't really get a lot of fine dust from a planer, it is mostly chips of wood. 2 Quote
Andy Wright Posted January 17, 2017 Report Posted January 17, 2017 One of these https://www.google.com/search?q=cyclone+trash+can+lid With a 30 gallon trashcan and a shop vac filter on the output should work well. Quote
wtnhighlander Posted January 17, 2017 Report Posted January 17, 2017 The chip ejector in my DW735 is powerfull enough to fully inflate the bags of my 1.5hp delta dc, through 10' of 4" flex hose, with the dc off. Pretty sure it will work through a cyclone, especially if you have only a coarse filter after it, or vent outside. Like several have said, the planer produces shavings, not so much dust. Quote
woodbutcher74 Posted January 17, 2017 Report Posted January 17, 2017 16 hours ago, Andy Wright said: One of these https://www.google.com/search?q=cyclone+trash+can+lid With a 30 gallon trashcan and a shop vac filter on the output should work well. I tried that. The filter will be full of shaving in no time. Went with a Jet Vortex Cone. Got tired of experimenting and wanted to woodwork. Quote
Marmotjr Posted January 18, 2017 Report Posted January 18, 2017 On 1/16/2017 at 0:11 PM, C Shaffer said: Just noodling here... Do you think the blower is strong enough to drive a small cyclonic action without the need of an impeller if the pipe were only two or three feet long? Like this? I just setup my 735x today, and ran it for the first time. And yes..... I used a pillowcase and a drawstring. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.