Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

argghhhh what did i do wrong?? ! maple slab dots

Featured Replies

hi. First time poster. I have no idea what I have done wrong or how to fix it. I am planing down my first slab. It is maple and I finished filling all the cracks with epoxy. I have been working it for the past few weeks. Yesterday I was finally done with all the epoxy and blemishes and had finished hitting it with 400 grit on the belt sander. I then went to 500 and 2000 using wet dry sandpaper and spraying water on the piece as I went. I was under the impression you get a better sand using wet/dry when it is wet. After completing what I thought was a decent rub down of the 2000 paper I got some fresh water and rubbed down the top with steel wool thinking I was taking all the remaining sawdust and debris away. When I woke up this morning I found that my slab is now covered in black spots everywhere... a light sand did little to get rid of them. What did I do wrong and does anyone have any idea how to remedy? I read one post that had a similar issue used something called oxalic acid? no idea. please help. 

IMG_20170820_200138.jpg

IMG_20170820_200143.jpg

IMG_20170820_200149.jpg

IMG_20170820_200210.jpg

5 minutes ago, macm said:

I got some fresh water and rubbed down the top with steel wool

This.  Welcome to the forum!.  Steel wool, is iron it reacted to the water, left the black spots.  What are you going to use the piece for?  There is no particular reason to go past 180 on most pieces, 220 at the most.  

  • Author

Damn... Any suggestions to getting rid of the spots without having to go crazy on sanding again? I was planning on trying to wax it with some red mixed in. I think it would look great against the black epoxy. 

PS thanks for the reply. 

Mac

What kind of wood?  Can you lightly sand and remove the spots?  It looks like there may be some reaction with the tannin in the wood I am not sure.  Some wood is worse than others.  My guess would be sanding, but there are  some really smart people on here that should have better advice.  

 

 

Go back to 120 grit and sand the whole slab.  Then work your way up to 220 and stop.  There's no reason to go any higher than that.  Once a piece of wood feels smooth and shows no scratches, it's time to move to finish.  I don't even sand my finishes higher than 600 grit until the final polish, and even then I stop at 1,000.  Sanding wood any higher than 220 (or 320 on end grain) is a complete waste of time...any higher grit should be done on finish.  Make sure you have proper dust collection so you're removing the sanding waste, and don't use water while you sand.  Wet sanding raw wood with water will never work because water raises the grain.

Check out Marc's video on this live edge slab. I haven't tried it but in the future, when I try something with a slab, it will be following something like this.

 

 

 

As Eric said, go back and sand. I occasionaly use iron acetate to color the wood surface, and it penetrates a bit. Since what you have are essentially rust stains, hopefully they will be right at the surface.

When you get to the final grit, you can wipe on a bit of water to raise the grain, swelling the surface fibers so that they stand out. Wait until the surface is dry, then hit it on more time.

I agree that the stained layer will have to go.  I would take a few swipes with a card scraper first to see if I was going to get off easy.  If that does it I would lightly do the whole surface taking care not to be too aggressive and leave scallops.  The logic here is that if a light pass or two with the scraper does the job, you will save a lot of sanding. 

Since you mention a belt sander and not a hand plane for surfacing I'll assume you'd like to sand.  A piece of 220 stuck to a 20" or so long board milled flat will help you retain the same plane while sanding.  You can go straight to this if you have no scraper but, change your paper often; over using abrasives (trying to eek out a little more work from worn paper) is a waste of time.

Call around to see if a cabinet shop has a wide belt sander, and would run it for you.  If shouldn't cost a whole lot.  I have a place that has run some things for me.  They know that I'm not going to waste their time talking, and would probably charge me 15 bucks.  With such a charge, I'd hand the owner a 20 dollar bill, and say, "Thank you."

  • Author

Thanks for the advice.  It seems the consensus is that I have no choice but to sand again. I have a 4x24 sander so it does a pretty good job. I just didn't want to take more material off again.

Bummer. 

Agree completely with Tom!  Find someone with a drum sander!  What will take you several hours will take a few minutes.

My suggestion, even if you take is somewhere to get sanded, you're gonna have to pay a few bucks to do that. Go by an inexpensive ROS and get busy. Start at 80 grit and work your way up to 150 grit. The ROS will give you a much better sanded surface than a hand belt sander.

 

-Ace-

  • Author

Yeah I think this thread has gone a different direction from what I was asking. I was wondering if anyone knew a way to remove the iron spots that I created without having to sand like crazy. 

 

43 minutes ago, macm said:

Yeah I think this thread has gone a different direction from what I was asking. I was wondering if anyone knew a way to remove the iron spots that I created without having to sand like crazy. 

 

Nope.  That staining is in the wood and the only way to remove it is by removing wood.

24 minutes ago, AceHoleInOne said:

Mama said there would be days like these:P

 

-Ace-

Fixed it.

8 hours ago, macm said:

Yeah I think this thread has gone a different direction from what I was asking. I was wondering if anyone knew a way to remove the iron spots that I created without having to sand like crazy. 

 

Easy fix? No sir! It took you a while to screw it up and it'll take you a while to get back to where you want to be. Beats the heck out of starting over with a new piece and it's a cheap lesson learned. 

And you don't forget lessons learned this way . It won't be so bad once you get going on it. You don't have to do as many fine grits as you did the first time.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.