collinb Posted November 10, 2017 Report Posted November 10, 2017 Looking at smaller bench-top options. Jet 10-20 open arm vs Shop Fox W1740. Anyone here use either, and any reason to avoid either? Quote
Guest Randy Posted November 10, 2017 Report Posted November 10, 2017 Don't know about brands, but capacity would be what I would think about before buying. I have a friend who has the Jet 10-20 and he loves it. However, he has found enough situations where the 20" capacity isn't enough. Even with a 16-32 projects would come up that you would want wider, but they would certainly be less. Obviously, if you can afford it and have the room, a 19-38 would be my ideal. Having said all of that, the 10-20 would still be useful for sanding veneer and smaller projects, so it would certainly be an improvement over no sander. All depends on what you usually make and/or plan to make. Quote
krtwood Posted November 10, 2017 Report Posted November 10, 2017 I have the 10-20. It's very difficult to get the paper to pull completely tight where it goes into the clamp at the right side which often means that the last inch or so of the drum isn't usable. It will just sand really deep there and quickly burn out the paper that's sticking out. Most of what I use it on it on is 8" or less so that's not something I really worry about, but if you think you need the whole 10" then save yourself a lot of trouble and get something bigger. Quote
Cheeset202 Posted November 10, 2017 Report Posted November 10, 2017 Highly recommend the Supermax 16-32 or 19-38 if you can swing it. They are built by the old Performax guys with many improvements! Installing paper and leveling drum are a piece of cake, 1 Quote
Guest Randy Posted November 10, 2017 Report Posted November 10, 2017 Except that I believe Performax was recently bought by another company; I think Laguna. Only time will tell if the resulting products are as good Quote
Chet Posted November 10, 2017 Report Posted November 10, 2017 34 minutes ago, Randy said: Except that I believe Performax was recently bought by another company; I think Laguna. Only time will tell if the resulting products are as good SuperMax is part of Laguna now, but the way I read the news on this is that they are still basically going to be separate from each other. I think what SuperMax was after was the increase in distribution network that Laguna has. Quote
mikemenifee Posted November 11, 2017 Report Posted November 11, 2017 I also have the 10-20 and agree with krtwood about paper also extremely difficult for me to change paper. Didn't realize how much I would use the drum sander, just purchased a supermax 19-38 Quote
wdwerker Posted November 11, 2017 Report Posted November 11, 2017 I just upgraded to the Supermax 19/38. I started out with the Performax 16/32 and it's a little tricky to get the paper in right, but it is achievable. Quote
Mick S Posted November 11, 2017 Report Posted November 11, 2017 A friend of mine got one of the new Supermax 16-32 units and loves it. I have the 19-38. Really nice features on the 16-32. Quote
difalkner Posted November 11, 2017 Report Posted November 11, 2017 We have the SuperMax 19-38 and it's a great machine. The paper is easy to change, as well. I'm doing a lot of 17"x28" Walnut plaques and leave them oversize until I finish with all of the sanding so they're really about 18"x29" right now. I'll step through grits 100-120-150-220 and it only takes about 2 minutes to change paper; I don't even shut the DC off because it's so quick. David 1 Quote
gee-dub Posted November 11, 2017 Report Posted November 11, 2017 45 minutes ago, difalkner said: I'll step through grits 100-120-150-220 and it only takes about 2 minutes to change paper; I don't even shut the DC off because it's so quick. David This pretty much describes much of my use. Quick and easy. 1 Quote
collinb Posted November 13, 2017 Author Report Posted November 13, 2017 On 11/11/2017 at 11:11 AM, gee-dub said: This pretty much describes much of my use. Quick and easy. Too bad nobody has put put two, three, or four drums on a turret. Quote
wdwerker Posted November 14, 2017 Report Posted November 14, 2017 They make double drum sanders, one behind the other on the same conveyor. That lets you sand 2 grits with one pass. Quote
Coop Posted November 14, 2017 Report Posted November 14, 2017 Collin, I’m sure you’ve been on here long enough to know that the consensus is that the Super-Max is the go to machine. However, I did not listen and bought the Jet 16-32 and don’t have a complaint one. But it depends on your needs and pocket book. Both of mine are relatively small. 2 Quote
collinb Posted November 14, 2017 Author Report Posted November 14, 2017 9 hours ago, K Cooper said: Collin, I’m sure you’ve been on here long enough to know that the consensus is that the Super-Max is the go to machine. However, I did not listen and bought the Jet 16-32 and don’t have a complaint one. But it depends on your needs and pocket book. Both of mine are relatively small. Not everyone can drive a Benz but a Toyota will still get you there. But watch out for that used Yugo. 1 Quote
Marmotjr Posted November 14, 2017 Report Posted November 14, 2017 On 11/13/2017 at 1:28 PM, collinb said: Too bad nobody has put put two, three, or four drums on a turret. We have a Heesemann "drum" sander at work, it has 4 60" wide belts that can be run like that. Computer controlled down to .1mm, etc etc. But not a machine for the home shop. 1 Quote
collinb Posted November 15, 2017 Author Report Posted November 15, 2017 13 hours ago, Marmotjr said: We have a Heesemann "drum" sander at work, it has 4 60" wide belts that can be run like that. Computer controlled down to .1mm, etc etc. But not a machine for the home shop. I guess that means you can't bring it up to Westerville for the weekend? ;-) Quote
Marmotjr Posted November 16, 2017 Report Posted November 16, 2017 Nope, even though I know where that is as my ex fiancee's family is there. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.