Mark J Posted February 2, 2025 Report Posted February 2, 2025 You're making quick work of this project, Coop. (Could the chair be next?) 2 Quote
Popular Post Coop Posted February 2, 2025 Author Popular Post Report Posted February 2, 2025 On 2/2/2025 at 8:27 AM, Mark J said: (Could the chair be next?) I have a couple of procedures scheduled with my dermatologist this Thursday and, as I have already rough cut the parts for the next stool, I plan on completing it, sans the tiles next. After the doc gives me the ok, I’ll start the chair. 5 Quote
Popular Post Mark J Posted February 2, 2025 Popular Post Report Posted February 2, 2025 Hope the procedures and the results go well. We'll be looking forward to the chair build. 3 Quote
Von Posted February 2, 2025 Report Posted February 2, 2025 On 2/2/2025 at 11:23 AM, Mark J said: Hope the procedures and the results go well. We'll be looking forward to the chair build. +1 1 Quote
Popular Post Coop Posted February 3, 2025 Author Popular Post Report Posted February 3, 2025 Might have screwed the pooch on this one. This is the 6/4 board that I bought for the chair. With a little hit with the belt sander, this is the grain I was dealt with for the chair. The rest of the 10’ board is similar. 3 1 Quote
fcschoenthal Posted February 3, 2025 Report Posted February 3, 2025 On 2/2/2025 at 8:45 PM, Coop said: Might have screwed the pooch on this one. This is the 6/4 board that I bought for the chair. With a little hit with the belt sander, this is the grain I was dealt with for the chair. The rest of the 10’ board is similar. And a 6/4 x 10' board isn't cheap. I just paid $60 for 8bf the other day. 1 Quote
Chestnut Posted February 3, 2025 Report Posted February 3, 2025 I remember when it was like pulling teeth to try and get Coop to post a picture. This is AWESOME! Loving the project and the documentation. 2 Quote
Mark J Posted February 3, 2025 Report Posted February 3, 2025 11 hours ago, Coop said: Might have screwed the pooch on this one. This is the 6/4 board that I bought for the chair. With a little hit with the belt sander, this is the grain I was dealt with for the chair. The rest of the 10’ board is similar. Admitting my ignorance, what is undesirable about the grain? 1 Quote
Popular Post Coop Posted February 3, 2025 Author Popular Post Report Posted February 3, 2025 When using the router with the flush trim bit on the two stools, I had a couple of problems of tear out and those boards were relatively straight grain. Not sure what to expect with this gnarly stuff. Maybe just closer cutting around the template on the bs and using hand planes and rasps to get me there? 4 Quote
RichardA Posted February 4, 2025 Report Posted February 4, 2025 I'm pretty sure you have the hand planes. 1 Quote
Coop Posted February 4, 2025 Author Report Posted February 4, 2025 On 2/4/2025 at 5:51 AM, RichardA said: I'm pretty sure you have the hand planes. And sharp, thanks to you! Quote
Popular Post Chestnut Posted February 4, 2025 Popular Post Report Posted February 4, 2025 For template routing in swirly grain situations, i tend to have a top and bottm bearing bit and flip my work piece over. You have to make sure to adjust the bit height accordingly. THIS IS NOT RECOMMENDED but sometimes when i have no way around swirly grain i do climb cuts very carefully and only with large work pieces attached to template sleds that I can get a good grip on. AGAIN THIS IS NOT RECOMMENDED. 3 Quote
RichardA Posted February 4, 2025 Report Posted February 4, 2025 On 2/4/2025 at 6:54 AM, Coop said: And sharp, thanks to you! Try the big white one! 1 Quote
Popular Post Coop Posted February 5, 2025 Author Popular Post Report Posted February 5, 2025 On 2/4/2025 at 5:29 PM, RichardA said: Try the big white one! I’ll give er a go. I don’t think I explained and it’s probably obvious but, the tiles are held in place via 1/4” black poly rope that is woven through the tile holes and in and out the holes in the frame. The author of the article demonstrates pushing this 1/4” rope through 1/4” holes in the two sides and nine tiles but I found out real fast on the last stool that this ole boy isn’t capable, even after enlarging the hole a tad. I devised a “needle” from some stiff ceiling hanging wire by filing a small slot in one end and connecting it to the end of the rope with some monofilament. Prior to tying the monofilament to the rope, I heated the rope end with a torch and with a pair of gloves, while still hot, I stretched the rope to a point so that it wouldn’t fray and to make it easier to thread through the holes. The author also uses two square knots at the entrance and exit to tie off the ends. My knot tying skills have not improved since my Cub Scout days a few years back so I had to come up with another way to secure these ends. My previous job required using s/s airplane cable and crimps so I came up with another idea. A visit to my Ace Hardware produced 1/4” id brass bushings or bearings to be crimped at the rope ends. I painted them black to blend in. The two holes in the frames where the rope enters and exits were drilled out slightly to recess these. I also found on the construction of the first stool that support from underneath the tiles made threading the rope through worked better than trying to hold the tiles in place with one hand with the needle in the other so I cut a piece of ply to fit that purpose. Pushing and pulling and cussing, I began threading tiles. When all of the tiles had been roped into place, I used a swaging tool to crimp the bushing at the entrance hole. With the aid of a friend and pliers and a screwdriver, we were able to pull all or most of the slack in the rope and crimp the other end. A knot was tied there also to hide the bushing and for looks. So, that’s two down and one to go a little later and I won’t bore you with that one. Thanks for watching. 10 Quote
wtnhighlander Posted February 5, 2025 Report Posted February 5, 2025 Looks really good, @Coop! 1 Quote
Popular Post RichardA Posted February 5, 2025 Popular Post Report Posted February 5, 2025 On 2/4/2025 at 8:23 PM, Coop said: I’ll give er a go. I don’t think I explained and it’s probably obvious but, the tiles are held in place via 1/4” black poly rope that is woven through the tile holes and in and out the holes in the frame. The author of the article demonstrates pushing this 1/4” rope through 1/4” holes in the two sides and nine tiles but I found out real fast on the last stool that this ole boy isn’t capable, even after enlarging the hole a tad. I devised a “needle” from some stiff ceiling hanging wire by filing a small slot in one end and connecting it to the end of the rope with some monofilament. Prior to tying the monofilament to the rope, I heated the rope end with a torch and with a pair of gloves, while still hot, I stretched the rope to a point so that it wouldn’t fray and to make it easier to thread through the holes. The author also uses two square knots at the entrance and exit to tie off the ends. My knot tying skills have not improved since my Cub Scout days a few years back so I had to come up with another way to secure these ends. My previous job required using s/s airplane cable and crimps so I came up with another idea. A visit to my Ace Hardware produced 1/4” id brass bushings or bearings to be crimped at the rope ends. I painted them black to blend in. The two holes in the frames where the rope enters and exits were drilled out slightly to recess these. I also found on the construction of the first stool that support from underneath the tiles made threading the rope through worked better than trying to hold the tiles in place with one hand with the needle in the other so I cut a piece of ply to fit that purpose. Pushing and pulling and cussing, I began threading tiles. When all of the tiles had been roped into place, I used a swaging tool to crimp the bushing at the entrance hole. With the aid of a friend and pliers and a screwdriver, we were able to pull all or most of the slack in the rope and crimp the other end. A knot was tied there also to hide the bushing and for looks. So, that’s two down and one to go a little later and I won’t bore you with that one. Thanks for watching. Over the years we've known each other, I've often wondered why you like to go to the park. At first I thought it was to walk your dog. Now I know the real reason. You go to the park, so you can knock things outa the park. As you did with this piece! 3 Quote
treeslayer Posted February 5, 2025 Report Posted February 5, 2025 Awesome work @Coop , I would say as usual but that is some next level work there, well done sir! 2 Quote
Mark J Posted February 5, 2025 Report Posted February 5, 2025 Good looking seat, and it looks like it is comfortable to sit in! 1 Quote
Coop Posted February 5, 2025 Author Report Posted February 5, 2025 Thanks guys. The author of the article said a customer of his was an old trucker that compared it to the old wooden beaded seat supports that were used at one time. 1 Quote
Popular Post pkinneb Posted February 5, 2025 Popular Post Report Posted February 5, 2025 This is too cool Coop! Great execution and thanks for taking us along!! My youngest and her husband just bought a house in Chicago and I think I'm gonna see if they would like one these as I really want to try making one but don't have anywhere to put it. They went from an 800 sq ft apt to a 2200 sq ft house so they should have room 3 Quote
Coop Posted February 5, 2025 Author Report Posted February 5, 2025 Paul, I have the digital templates from FWW for the chair if you want to undertake it but they didn’t provide one for the stool. I got my measurements for the stool by counting the tiles and the article gives the dimensions for the tiles. 1 Quote
pkinneb Posted February 6, 2025 Report Posted February 6, 2025 On 2/5/2025 at 5:21 PM, Coop said: Paul, I have the digital templates from FWW for the chair if you want to undertake it but they didn’t provide one for the stool. I got my measurements for the stool by counting the tiles and the article gives the dimensions for the tiles. Seeing the kids later this month and will definitely take you up on that if they are in Quote
Von Posted February 6, 2025 Report Posted February 6, 2025 +1 Really nice looking piece and thank you for the walk through. 1 Quote
gee-dub Posted February 7, 2025 Report Posted February 7, 2025 I am digging this thing so much. The look is right out of my childhood. Keep it coming. Quote
Popular Post Coop Posted August 29, 2025 Author Popular Post Report Posted August 29, 2025 I’m now building my 4th and 5th stools. One for my ex-son-in-law ( yeah, he’s still a good ole boy) and another for my house. SIL gets one like the above from walnut. Mine is being made from some qtr sawn sycamore that I bought from Ricky, aka @Spanky in Tennessee. The sycamore planks are 9/4 x 10” x10’ and were milled and kiln dried and have been stickered and stored for the last 8-9 years. The frame of the stools require them to be 1 5/16 so I re-sawed them and this was what was inside. Before re-sawing and after. 6 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.