Shane Jimerfield Posted November 10, 2014 Report Posted November 10, 2014 Folks, I recently purchased a new table saw - not going to say the brand and model just yet - but it has few issues and I was wondering what your thoughts are. 1) I cannot get the blade parallel to the miter slots. There is not enough play in the table to base adjustment to make it parallel. It is off by .01" from the front of blade to the back (same spot on the blade, marked and rotated). They are telling me that is within the manufacturer's specs of 20k. 2) The main table and the wings on both sides do line up properly. When I adjust for the front and back to be flush then the middle of the main table sits proud of the wings on both sides by .015". There is a very obvious rise when you run your finger across the joint. A flat edge will slide right across the front and back, but hits/stops solidly at the center. 3) Both wings when bolted to the main table slope down toward the outsides. This is a significant slope. It drops by .15" across the 12" wings. I'm not really feeling the love from their customer service. He keeps talking about the manufacturer. It is still early in my conversations with them, so I am not yet ready to throw them under the bus and blow the whistle. He said he would ship me a new table, but now wants a photo of the warp. What? How the heck am I supposed to do that? They do make good machines. I just think I unfortunately got a lemon in the bunch. It is not a top end machine, but it is marketed as being of very high quality and reviews are great. Am I being too picky, or are they not stepping up? Thoughts, opinions? Bummed in Southern Oregon, Shane Quote
chefmagnus@grics.net Posted November 10, 2014 Report Posted November 10, 2014 I would wait and see what happens. If they fix the problems, then cool tell us that they fixed things up with you. If not also let us all know. More than 10 years ago I bought a Delta high end contractors saw. Got it home and stripped the plastic off the top and my first thought was that there was a long hair on the top. But no it was a crack that ran from the blade opening to the corner of the saw. Only the fact that it was bolted down kept it from falling off. Delta was completely in the clueless department. They told me that I was going to have to wait 12-16 weeks to get a replacement top from Asia and I was going to have to pay shipping from Long Beach, CA to IN where I was living. I called Lowe's and sent it back. I exchanged it for the DeWalt that I have today. And it arrived without a motor cover. Lowe's did find me a motor cover and DeWalt sent me 2. They did't want them back either. So I put some cheap wheels onto the extras and use them as scrap bins. My dealings with Delta 10+ years ago has poisoned the well so to speak on me getting any of their products. I have just gotten one of their older drill presses and it works great for me. Quote
Trip Posted November 10, 2014 Report Posted November 10, 2014 ==>How the heck am I supposed to do that? Another reason to own a good straitedge and feeler gauges... Won't comment on the tolerances -- if the mfg specs something and the top's within spec, there's not a lot you can do... If you want to photo the defect, span the dip/warp/whatever with the straight edge, slide the biggest feeler you can manage take a snap of the setup... That should do it... Quote
bob493 Posted November 10, 2014 Report Posted November 10, 2014 Ive had problems, needed to the get the... i dont remember what they are called... they press against the saw blade and needed to be flatten. sent them to a shop to have them surfaced, and then it ran like new. Quote
Shane Jimerfield Posted November 10, 2014 Author Report Posted November 10, 2014 Yeah, I did that. It's hard to photograph a .015" rise across 27". The photo does not really show anything except a feeler gauge under a straight edge, but I guess that's their problem. Problem is they don't put the manufacturer's specs on the website. Which brands do? Who the heck would buy a nice table saw that was speced out at .02" over less than 10" on the miter slot to blade? I'll spend 2 hours if I have to to get my sled < .005" across 48". But no can do if the blade and slot are not parallel. Quote
bob493 Posted November 10, 2014 Report Posted November 10, 2014 Oh I see what you mean now. If the blade rotor isn't square, its gonna be tough to fix that mate. Is there an adjustment on your saw for that? Quote
TerryMcK Posted November 10, 2014 Report Posted November 10, 2014 10 thou should be very easy to get spot on. I presume the top bolts from the underside as you haven't given indication of what the saw is. There will be tapped holes in the cast iron top. What you need to do is file the clearance holes in the bottom to make them into slots. Not sure if it is pressed steel or a casting. Either way it should be very easy to do with a round file. Or simply open the hole up slightly with a larger drill. On query 2. Are the wings made from pressed steel? If they are then they can be persuaded to lie flush with a mallet. If they are cast iron then don't hit them as they will crack. On query 3 you are saying the wing slope downwards. You can compensate for that by shimming the lower part of the mating faces. Most wings I have seen have small grubscrews that can be adjusted for this very reason to jack the wings into position. I would be more worried if the wings were leaning upwards but even then it can be adjusted by shimming at the top of the mating faces. Quote
knotscott Posted November 10, 2014 Report Posted November 10, 2014 There's little to be gained by withholding the brand and model...knowing that could give us a lot of info about the design and adjustments on the machine, which ultimately could give us some insights about your issues. You should be able to shim the wings. The table flatness can be tested by making some cuts...it'd take a sizeable deviation to significantly alter the cut....if the cuts are off I'd send it back. The alignment should be more like +/- 0.003". 0.01 is too much if it pinches on the workpiece....if the trunnions can't move any farther, you can make up small deviations by adjusting the fence. Quote
Jfitz Posted November 10, 2014 Report Posted November 10, 2014 ^^^ what Terry said. #3 is easily remedied by shimming the table/wing joint to force it up or down as needed. thin brass stock, or even small pieces cut from an aluminum can, work well. The first issue is the most severe, so you'll have to file out the mounting holes somehow to get more play in the movement of the table. Quote
dwacker Posted November 10, 2014 Report Posted November 10, 2014 You don't take your car to the the shop and expect them to fix it without knowing the make and model. We can give advise based on experience but contrary to belief they are not all the same. Sound like your dealing with the retail sales company, place of purchase. Most of the time you will have better luck with the manufacturer. I wouldn't bother dealing with a retail store for a PM problem so much easier going to the manufacturer. I don't care what brand you buy there will be an issue here and there. Expecting accurate advise while withholding needed info is not the way to go about this sort of thing. Quote
Eric. Posted November 10, 2014 Report Posted November 10, 2014 1 and 3 are easy fixes, as Terry noted above. If the main table is warped significantly, I would fight tooth and nail to get a replacement. Having trouble understanding...the wings are warped, your table is warped, or both? If it's the wings, remember that as long as they're not positioned higher than the main table, they're inconsequential. The wings are only there for supplementary support...all the registration that matters is at the main table. Set the highest point of your wings just a hair below the main table...a fraction of a hair...and as long as they don't deflect the angle of a longer workpiece, they mean nothing. It's annoying to feel and see that slight discrepancy at the joint...but you get over it. But again, if the table is significantly warped, I'd send it back without thinking. Significant is a bit subjective. If I could get a dead-nuts 90* cut on a dozen workpieces of varying sizes, it's not significant. 1 Quote
Shane Jimerfield Posted November 10, 2014 Author Report Posted November 10, 2014 thanks for all the tips. Indeed the main, unfixable issue is the warped main table. Shims and and a file fix the other two. I'll send the photo today and see what they say. I guess what I'm really after here is a sense of wether given that there are three significant defects should I keep this thing or fight to send it back, or get a replacement? After reading the great reviews and dumping the cash I was not really prepared emotionally to have to make all the repairs needed. If I'd picked it up on craigslist for half the price all these repairs would have been done already and I'd feel good about it, but this is a new saw. I guess I'm feeling a bit cheated out of that "I just a great new tool" feeling that will plague my relationship with this saw forever. Quote
Beechwood Chip Posted November 10, 2014 Report Posted November 10, 2014 I know how you feel. When I bought my Sawstop I had to go back and forth with the retailer. I was already in sticker shock and feeling kinda guilty/foolish over how much I had spent, and then to have problems with the assembly just made my head explode. For the record, the Sawstop was fine - the problem was Woodcraft giving me the wrong extension table for the saw. Twice. And I have to say that after I talked to the manager, they made it right. They delivered the correct extension table to my home and did the installation for me, including all the adjustments and fine tuning. Good luck with your new saw! A couple of months from now, this will all be a memory and you'll be happily making sawdust. Quote
ChetlovesMer Posted November 10, 2014 Report Posted November 10, 2014 Back in 2007 I bought my table saw (a SawStop Industrial Cabinet Saw) from Acme Tool in Des Moines. They delivered it. Set it up. Confirmed I was happy with it. They absolutely over performed in their making sure I was happy with everything. To this day I still brag about them and still buy from them. What's the commercial? You only get one chance to make a first impression. Quote
estesbubba Posted November 10, 2014 Report Posted November 10, 2014 There's little to be gained by withholding the brand and model...knowing that could give us a lot of info about the design and adjustments on the machine, which ultimately could give us some insights about your issues. I agree that brand and model would allow people to know if this is a common problem and if the manufacturer is good at making things right. That said, no matter who made the saw, I would be firm in getting what makes you feel good and not what makes them more cash. I know how you feel about getting something brand new and having problems. When I got my Grizzly cyclone, the trucking company put a forklift into the box and scratched the blower housing. Grizzly offered a gift certificate if I kept it, and since the scratch will be facing the wall and unnoticeable, I'm happy. Quote
Rick A McQuay Posted November 10, 2014 Report Posted November 10, 2014 The Delta contractor I bought around 15 or 16 years ago had issues #2 & #3 as well. Shimming fixed #3. The left cast iron wing doesn't sit perfectly flush with the saw top and it is a tiny annoyance but does not affect my cuts. I can feel the difference with my fingers but a board slides right over it. Incidentally, on a positive note ... the saw was missing a couple bolts when I got it home. Called the retailer who told me it would be a couple weeks. Hung up and called Delta who overnighted the bolts with Saturday delivery. My blade and miter slot alignment was dead on though, at least to my ability to measure it back then. If you can't align the blade on yours that would prompt me to send it back. Quote
Tom Cancelleri Posted November 10, 2014 Report Posted November 10, 2014 Fixing the droop in the wings should be an easy fix. If you watch Marc's video on setting up a table saw, you can put tape on the bottom part of where the wings attach to the table, and then reinstall and check it. Fixing the blade parallel to the miter slot is an interesting one, is it a contractor saw or a cabinet saw? Cabinet saw has bolts in the corners for the top, and for a contractor saw you need to loosen the trunnion which I find to be a huge pain in the ass. You can also try to coerce that .1" that it's off by with a dead blow. if it's off by 20/1000, you're looking at roughly 3/128ths which is acceptable in woodworking. getting it 0 across the board is gonna be nearly impossible. When I setup my saw the closest I was able to get it was 8/1000. Quote
Mzdadoc Posted November 11, 2014 Report Posted November 11, 2014 I'm going to take a different approach because I'm "The guy" that always gets the broken item in a new box. Also the guy that grabs the short line to watch the long line go twice as fast. My wife can verify this! LOL With this said I'm all about the relationship with my new expensive purchase. If it's not perfect in my eyes and that includes customer service I walk away and don't look back! The products I own are because of quality and customer support. If you're disenchanted then I'd say walk away but...... Are you talking to the retailer (don't) or manufacturer? (Do) Quote
Shane Jimerfield Posted November 11, 2014 Author Report Posted November 11, 2014 I've been talking to the manufacturer, kind of. Not the dealer. The brand is not, as we know, who manufactures...it's made in Taiwan. The guy at the brand keeps referring to the manufacturer. It's really kind of weird. Quote
Shane Jimerfield Posted November 11, 2014 Author Report Posted November 11, 2014 The customer support rep at the brand keeps referring to the manufacturer in the second person. Well I know the things are made in Taiwan, but I thought these guys took more pride in their machines, more ownership. He kept complaining how the "manufacturer keeps changing things and not telling us." "They don't even update manuals." blah, blah, blah... The experience is not sitting well with me. I've sent the photos and hope they saddle up and do the right thing here, or a full report will be published. A report will be published, but these gory details may have to be included. To be honest at this point I just wish I had my money back, and my 15 year old Rigid - that trusty old dog served me well. I should not have abandoned him. Who thought a machine could get me so worked up, and broken hearted. Quote
..Kev Posted November 11, 2014 Report Posted November 11, 2014 Piss poor service loses my business every time. I would demand a refund and return the saw regardless of what brand it is. Quote
ResidentEvil Posted November 11, 2014 Report Posted November 11, 2014 Yea. For a bigger purchase like that they get one, maybe two, chances to make things right. I understand that nothing is perfect and that little things can happen. But that is just the companies opportunity to step up and show their excellent customer service and make it right with as little inconvenience to you as possible. The fact that they didn't just come right out and immediately offer to make it right tells me all I would need to know. This is a brand new machine with a problem that they are seemingly reluctant to fix, what is going to happen in 18 months when you need to get something fixed on warranty? I'd pack it up and take it back, or call them and tell them that they need to arrange to have it shipped back to themselves if you had it delivered. Quote
woodbutcher74 Posted November 11, 2014 Report Posted November 11, 2014 I can't accept poor quality in things I build, so I won't accept it in things I purchase from somebody else. You'll never be happy with it. Return it !!! Make sure you tell everybody that will listen, Quote
collinb Posted November 11, 2014 Report Posted November 11, 2014 The customer support rep at the brand keeps referring to the manufacturer in the second person. ::: Who thought a machine could get me so worked up, and broken hearted. Apparently a private-label product. Not bad in and of itself, but apparently they do not have a good customer service model wrapped in their business model. It is just a machine. It can be fixed or replaced. Not like it's a person or something. But it's not the machine getting you worked up. It is the people and the company behavior. That's enough reason to jump ship. I do it every couple of years. Life is too short for headaches and heartaches. Quote
chrisb Posted November 11, 2014 Report Posted November 11, 2014 As someone that might be in the market for a new table saw in the near future, I would be interested in more details about your purchase. I really want to minimize my risk of having a similar experience. Chris. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.