Recommended Posts

Posted

Didn't want to hijack Duck's thread but, I had a bit of a different question for those of you with a drum sander..

What grit do normally run?  Do you change grits often?

Posted

I mainly use my drum sander for flattening and critical dimentioning. I keep 80 grit paper on mine 80% of the time and only move up when needed.

I keep a rubber paper cleaner close on hand and clean the paper often. I only really change it when something gums it up.

Posted

Brendon, you don't find the 80 grit hard to remove later with the ros? I finally quit using it unless I change to 120 or so later to remove the lines. And I hate changing paper more than blades on the ts.

Posted

I don't,  I start at 80 on the ros to remove the drum "lines" we hate, then go 120 then 180.. 

I also hate changing paper,  like really really hate it on the drum. 

If I was doing a piece that was going to be under heavy criticism, I may throw 120 on but again,  I don't really use the drum for finishing,  for for starting. 

Posted

I keep 120 on mine all the time. Works well for cleaning up glue lines and also for removing planer ripples. Seems to be a good grit for decent panel cleanup without a buttload of ROS sanding afterwards. 

Posted

80 grit is a beast on the drum sander.  I think it almost defeats the purpose unless you're using it as a planer in which case you're pretty much misusing it.  I don't ever find the need to remove that much material that quickly with the DS.  It's not meant to be a milling machine.  And frankly 80 leaves a rougher surface than a planer unless you're getting a ton of tearout.

I kept 120 on mine until I got a Shelix head for my planer.  I found that the Shelix actually leaves a smoother surface than the 120 so I've kept 150 on it since then.  The Shelix is so smooth, in fact, that I've actually dropped the drum sander from my workflow quite a bit for post-planer sanding.  Instead I'll take a few swipes with a smoothing plane.  I now use the DS mostly for leveling panels, smoothing veneers off the bandsaw, and dimensioning tiny parts.

  • Like 1
Posted

I run 50 and 80 at the same time for flattening. I will go to 220 sometimes, if the project is large enough. I would argue that 80 scratch lines are kinda tough to remove with a ROS. Nearly every project will get the paper swapped out for 120 and 180. Running dual drums is nice for going through your grits quickly, but im still changing paper as much as everyone else. I don't find it too bad. I can do a drum in 2ish minutes, so a whole change takes me 5 mins or so? Considering im sanding large surfaces like table tops, this is a no brainer. 5 mins to change paper and 5 mins to cycle through another 2 grits, or 45 mins doing it with my ETS 150/5? Whenever I do take a project to 220 off the drum, its a dream. Silky smooth with zero effort. Finish it off with the ROS 220 and 320 real quick and you are done. Im as lazy as the next guy, but if you don't change paper, then you aren't really using the machine to the best of its abilities.

Posted

36 grit is really a beast !  Flattening really wide stock isn't as slow using it. I switch to 60 and work my way down to 180, then ROS starting at 150 -180- 220.

I made a template out of 1/4 MDF so I can cut from rolls, cause the precut is so much more $$. I can switch grits fairly quick but it does take time to learn how. I struggled the first year or so with my original 16/32. It seems like the Supermax 19/38 made it easier with more room to get your finger in to the clamp.

Frequent checking and cleaning the abrasive for resin build up is important to avoid burns. 

  • Like 1
Posted

I tend to switch between 80 and 120 as a general grit on my machine..  I typically don't use it for finish sanding but, to sneak up on a final thickness.  Yes, the 80 leaves some fun marks for later and the 120 is just a bit slower..  I've been thru a couple rolls of each and hadn't really decided which I liked better so, thought I'd toss out the question..  

Thanks for the input!

Posted

I found that the Shelix actually leaves a smoother surface than the 120 so I've kept 150 on it since then.  The Shelix is so smooth, in fact, that I've actually dropped the drum sander from my workflow quite a bit for post-planer sanding.  Instead I'll take a few swipes with a smoothing plane.  I now use the DS mostly for leveling panels, smoothing veneers off the bandsaw, and dimensioning tiny parts.

Does this change your opinion overall on the DS?  I know a lot of people have had the "how did I ever live without it" feeling...but you seemed to have reversed from that at least somewhat. 

Posted

No I still love it and rely on it to do things that would otherwise be a total PITA...smoothing bandsawn veneers and dimensioning small parts especially.  Leveling panels can be fairly easily done with hand planes and scrapers but that's also a big plus.

I just don't find it to be the huge time saver in finish sanding that most people claim.  You can only go so high in grit on the DS...anything over 150 wants to clog and burn so fast that you're pretty limited in how smooth you can actually get a piece of stock before you have to move to the ROS anyway.  So I do a lot of initial smoothing after the planer with a #4 and/or #80, and then go straight to 180 or 220 with the ROS.  I just find this system faster and easier.  Maybe it's just me.

I still love the drum sander, I suppose I just see it as more advantageous for different tasks than the mainstream of DS owners.

Posted

I start at 80 then go to 100. That's it for the drum. Then I ros all the way up to 150. There have been times I wish I had 60 grit. Simply not enough juice for the squeeze to run higher grits on the drum sander. Thats how I roll anyway;)

-Ace-  

Posted

36 grit is really a beast !  Flattening really wide stock isn't as slow using it. I switch to 60 and work my way down to 180, then ROS starting at 150 -180- 220.

I made a template out of 1/4 MDF so I can cut from rolls, cause the precut is so much more $$. I can switch grits fairly quick but it does take time to learn how. I struggled the first year or so with my original 16/32. It seems like the Supermax 19/38 made it easier with more room to get your finger in to the clamp.

Frequent checking and cleaning the abrasive for resin build up is important to avoid burns. 

Steve, I've yet to buy extra as I'm still using the rolls that came with mine. Cutting your own using a template sounds like a good idea. What brand do you recommend?

Posted

Currently I am using some Chinese stuff that Peachtree Woodworking sells in rolls. It's pretty cheap and lasts ok. I used a precut strip to make my template on 1/4" MDF. I roll out the abrasive put the template on top and cut with a utility knife. While I am cutting I cut the whole roll. I think I get 7 strips per roll. I label the grit on both ends on the back with a Sharpie. Then roll it up and put a rubber band on it.

  • Like 1
Posted

I'm pretty much same as Eric.  I keep 120 on there (I have a straight knife planer) because I'm mostly using it for flattening panel glue ups and dimensioning small parts.  I've gone down to 80 before and I found it was a mistake.  Took WAY too long to sand out the tracks afterwards.  

Posted (edited)

 

I was just going to ask where you guys get your large rools of drum paper...I am using jet paper pay alot for it..
Edited by mat60
  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 66 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined