Recommended Posts

Posted

Welcome to the forums Jim.  I moved your post to the journal section.

We usually don't allow first time posters to drop a video in.  I sincerely hope you're not just trying to up your youtube views and hope you remain active in the forums.

On the video front, it thought it was very well done.

On the shop safety side, there was some scary stuff in there.

  • Like 1
Posted
3 minutes ago, TIODS said:

 

On the shop safety side, there was some scary stuff in there.

now I have to watch it... darn... I hate youtube.  

Posted
39 minutes ago, TIODS said:

Welcome to the forums Jim.  I moved your post to the journal section.

We usually don't allow first time posters to drop a video in.  I sincerely hope you're not just trying to up your youtube views and hope you remain active in the forums.

On the video front, it thought it was very well done.

On the shop safety side, there was some scary stuff in there.

I had to stop watching halfway through.  Everything he did with the TS gave me the willies.  

Posted

Welcome Jim....On the shop safety side it may be better for newcomers that see your videos if you would at least pretend to be safe...

Posted

Interesting mixture of equipment. CNC router, sliding tablesaw, ancient clamps and workbench. Scary tablesaw work ( but he did have the guard in place )

Neat looking flower that couldn't sell for the time and effort expended.

Posted

I liked the video,  and really like that old bench,  but for the love of fingers,  get an inset in that monster saw.  You had me puckered up all sorts of proper.

Posted
1 hour ago, wdwerker said:

Interesting mixture of equipment. CNC router, sliding tablesaw, ancient clamps and workbench. Scary tablesaw work ( but he did have the guard in place )

Officer, I may have been driving 100 miles an hour, drunk, in a school zone, but my car has anti-lock brakes, so no big deal, right?

Posted
28 minutes ago, xxdabroxx said:

What am I missing at the table saw? 

Off cuts dropping in. I was never bothered by that until someone told me it had some danger association. I never saw it be a problem in hundreds of occurances, but it only takes once. 

Posted
6 minutes ago, C Shaffer said:

Off cuts dropping in. I was never bothered by that until someone told me it had some danger association. I never saw it be a problem in hundreds of occurances, but it only takes once. 

If that hundreds is a real number, then I'm surprised you haven't seen an injury yet.  It's not so much the off cut as it is before it becomes an off cut dropping down in the throat plate can pull the whole board in pulling your hand into the blade. It's not even just a little dangerous, it's down right asking for trouble.

  • Like 1
Posted
22 minutes ago, Janello said:

If that hundreds is a real number, then I'm surprised you haven't seen an injury yet.  It's not so much the off cut as it is before it becomes an off cut dropping down in the throat plate can pull the whole board in pulling your hand into the blade. It's not even just a little dangerous, it's down right asking for trouble.

Conservative number at that. We used to rip the mill radius off of 2x material to get boards with square corners to wrap with aluminum coil stock. Any little knot and the off cut would break and drop. Not claiming I was wise at the time. Not even close some would say... They often fell out the bottom of the job site saws. 

Posted
6 minutes ago, C Shaffer said:

Conservative number at that. We used to rip the mill radius off of 2x material to get boards with square corners to wrap with aluminum coil stock. Any little knot and the off cut would break and drop. Not claiming I was wise at the time. Not even close some would say... They often fell out the bottom of the job site saws. 

Gotcha, we've all done that at some point....There's a slight difference to a small sliver off cut on a wider board falling in, and what he was doing. One not a good idea, the other, have a medic on standby. 

Posted
36 minutes ago, C Shaffer said:

Conservative number at that. We used to rip the mill radius off of 2x material to get boards with square corners to wrap with aluminum coil stock. Any little knot and the off cut would break and drop. Not claiming I was wise at the time. Not even close some would say... They often fell out the bottom of the job site saws. 

often times a job site stalls will stall before they pull you into a vortex of pain :)   

Posted
1 hour ago, xxdabroxx said:

What am I missing at the table saw? 

Isn't it also a no no to back boards out of a cut while the blade is still running?  Seems like asking for a kickback if you don't pull it straight back out.  It also looks at one point he reaches back behind the blade while the board is only halfway through the cut to pull it through from the backside.   

Posted
2 minutes ago, Lee Bussy said:

A CNC but no correct sized-bit to drill the hole in the flower center?

Also not seen him back here ... seems a hard way to get 495 YouTube views.

despite the safety issues (which I find more amusing than anything) I liked the video.  I liked the pace.  i could watch with no volume while doing something else and get some ideas.   But i agree getting youtube views is a slog.  a long hard slog.  

Posted

saw enough till i got scared then quit, somebody on the tube will try this and get themselves hurt, people say my son picked up my woodworking skills, but when he was in the shop with me i taught him to work safe and keep all his parts attached, this guy is headed for trouble and probably taking a few guys with him 

  • Like 1
Posted
2 hours ago, Lee Bussy said:

 

Also not seen him back here ...

He has had a lot going on today posting this flower thread as his first post on another woodworking forum also..:huh:

Guest
This topic is now closed to further replies.
  • Who's Online   0 Members, 0 Anonymous, 54 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined