Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Router Bowl!

Featured Replies

Okay, last Xmas project...

Purchased the CMT Bowl & Tray bit and collet extension last year. Time to finally put it to use.

Like turning, different species can be glued together for effect. The advantage of the B&T bit is the ability to make "unturnable" shapes.

I chose a pill-shape for the wood I had on hand and for the fact my bandsaw can't resaw anything wider than 6".

PSA. When buying a bandsaw, get the riser blocks and a couple of blades, even if you don't think you need them. You'll thank yourself later.

Final choice: white oak and wedge.

8a2aef049c40a25c02ff3e50911a81ca.jpg

Resawed...

418795331aaec8dff25a8426c593cbab.jpg

I left the edges unjointed. It will be trimmed away with the bandsaw later. The outside width of the bowl will be 5" and I will only have 6" to work with, so no room for error when laying down the template.

Glue-up.

082313e6f07e471eebc154962022cce0.jpg

72760817c83f89f2a71a8414800b6d2e.jpg

It's a shame much of the wenge will be turned into chips. It's a nice grain.

Next up, mdf template.

Stay tuned.

Sent from my iPad using Tapatalk

Gonna look good.  And I will stay tuned.

I have gotten good results with CMT bits. Be careful with that extension. Don't take to much depth in one pass. If your router is older the affect of worn bearings will be amplified by the extension. I am egaer to see how your bowl turns out ! 

Looking forward to seeing it move forward.  If you haven't worked wenge, you haven't lived.

  • Author

Update:

Unless your bowl is 2" diameter, chances are you will need a bigger base. For want of 3/8" plastic (small town blues) I laminated two pieces of 1/4" hardboard.

f239f71a48ad89cbd6f5e20969335917.jpg

529759a7b730f5c974e3b5d3b7f4359f.jpg

Template time...

09c52daab480ee8cb7a11956306a9cff.jpg

c94647074da8ebac74128b174dcac33c.jpg

As mentioned, I don't have much width to work with so centering the template across was crucial.

79c9aeb7fecda1bfb6ca4e9fb0adb6c3.jpg

One could easily begin routing at this point, but it's quieter, somewhat safer, and far less dusty to hog out as much as you can at the drill press with a forstner bit.

67a4e6d0b3519a516b2da6055ade761b.jpg

Some important considerations while at the drill press.

1. Forstners leave dimples. Unless you want your bowl to look like a golf ball, you need to account for this when setting the depth of your drill press.

2. Keep way from the template for two reasons. First, the B&T may follow the gouge if it's anything bigger than a hair. Second, you may end up leaving a squared-off bottom that can't be rounded out by the B&T bit.

3. Keep your work secure and empty out the chips often. See #2.

Hogged out. Had a close call when I tried to drill out a small area and the forstner bit jumped away.

0c808134c1d65af84adcdae7be7b5ed1.jpg

Ready to rout. I secured the blank with carpet tape on plywood. I really need to build that bench top soon.

26d9ba61692dcee4d747a0f6753c8c89.jpg

I used the stepped depth stops on my plunge base to take off small amounts each pass.

Half ways done.

92805c67f7b3b147212fbc2bec828d05.jpg

For the deepest pass, I had to loosen off the collet and collet extension to get a little more length.

Success!

00b7cfd91eb4cc1be364a5a021105a6b.jpg

Seems I uncovered something I did "knot" see.

Is it okay to leave it, or should I fill it?

Next up, bandsaw.

Sent from my iPad using Tapatalk

Id fill it with a little CA glue.  Will keep things from going in there (Food or dip or dressing whatever.) Should fill pretty easily, and should look just fine.  Looks good!

Interesting shape, what do you envision it being used for?

  • Author

Back to the router finish the base and top.

1/2" 4-cutter round-over to mitigate tear-out...

290a85ac2b583b567a4d559e409c07cf.jpg

And a 1/8" round-over for the top.

5886786311b5610584df947711eb9452.jpg

Wenge. I worked with it before to make the ribbon-handle boxes and didn't find it hard to work with. Not this time.

Sent from my iPad using Tapatalk

  • Author
  • Popular Post

Coat of tung oil...

d738fe33f98e53cc822263153a994733.jpg

Fin

This elf needs a rest!

Thanks for following.

Sent from my iPad using Tapatalk

Excellent job! I did a similar project in the shape of a snowman for my wife to hold candy. It's not a pretty as yours!

  • Author

Thanks for the compliments everyone!

Sent from my iPhone using Tapatalk

Nicely done.  Seems like some of the process were real nail-biters.  I like it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.