Recommended Posts

Posted

I received my new 4 piece set of Narex chisles Saturday afternoon after ordering from Amazon on Friday evening.

This morning I went to do a preliminary sharpening since they wouldn't shave the hair on my arm ( super sophisticated method) I laid the first chisel back down to check/flatten the back. About 30 seconds on 320 and the black markings (brand - size - model code) are all gone. They must just be surface painted.

It seems I'll have to mark the size on the handle with a sharpie or rotary marker. .

End of rant.

Posted

I have an old chisel from my dad with the marking "Sheffield" drop forged onto the back (near the handle).

John

which I assumed would be the case. My glue scraper which is an old chisel from a garage sale can still read "Sears made in America"
Posted

I have narex, a couple Irwin and a couple old marples, and even a few contractor chisels from Lowes.  Not one of them has the size anywhere! I grab a chisel that looks like it fits, if not, I grab the next size.... My dado blades don't have sizes marked, I force myself to actually think!  My hand saws don't have how many teeth marked on them, but I "know" which is rip and which is crosscut.  I don't get the problem!

  • Like 1
Posted

My 3/4" narex lost the markings when I was taking the lacquer off the blade. I've got it written in with sharpie.
 

The rest are fine, the markings are only painted/printed on, but are high enough on the blade I don't need to touch them.

Posted

It takes time and experience but after a few years you can just grab a chisel and know it's the right one. Start throwing metric and inch tools in the mix and it might take some labels !

Posted

It takes time and experience but after a few years you can just grab a chisel and know it's the right one. Start throwing metric and inch tools in the mix and it might take some labels !

 

Back before they started putting metric fasteners on everything I could just look at a nut or bolt on the vehicle or equipment I was working on and grab the correct socket or wrench at first attempt. Damn metric system sure tossed that particular skill in the toilet!  :angry:

  • Like 1
Posted

My chisels (PFeil) are all metric, but I work with imperial measurements. I have found knowing the size of the chisel doesn't matter.  I just grab the one that is closest to the size I need.

Posted

Back before they started putting metric fasteners on everything I could just look at a nut or bolt on the vehicle or equipment I was working on and grab the correct socket or wrench at first attempt. Damn metric system sure tossed that particular skill in the toilet! :angry:[/quote

as an old bmw tech, I can still do that with metric sockets. I just find it strange that they ink the sizes on there knowing one of the first things to be done with a chisel will erase it.

Posted

Back before they started putting metric fasteners on everything I could just look at a nut or bolt on the vehicle or equipment I was working on and grab the correct socket or wrench at first attempt. Damn metric system sure tossed that particular skill in the toilet! :angry:[/quote

as an old bmw tech, I can still do that with metric sockets. I just find it strange that they ink the sizes on there knowing one of the first things to be done with a chisel will erase it.

 

In a previous life I worked at an engineer's supply firm and in about 9 out of 10 cases I could tell head size, thread standard, pitch, thread included angle, and diameter.

 

Over here we have... Imperial (Whitworth) (55deg) , Unified (a standard adopted by a standards group convened in 1948 between US Canada and the UK), (60 deg),  Metric, (60 deg) and BA (45 deg from memory). For the old Whitworth the spanner nomenclature is based on the thread diameter so a 1/2" W spanner fits a standard 1/2" W bolt, unless they are using an oversized head in which case the 1/2" W bolt would use a 9/16" spanner.

 

We went metric in the 70s but that did not slow the sales of Unified and Whitworth.

 

Don't get me started.... :)

 

Now, what was this thread about again :o

 

John

Posted

I received my new 4 piece set of Narex chisles Saturday afternoon after ordering from Amazon on Friday evening.

This morning I went to do a preliminary sharpening since they wouldn't shave the hair on my arm ( super sophisticated method) I laid the first chisel back down to check/flatten the back. About 30 seconds on 320 and the black markings (brand - size - model code) are all gone. They must just be surface painted.

It seems I'll have to mark the size on the handle with a sharpie or rotary marker. .

End of rant.

 

Send them back! 

 

Defective for sure ... how is one supposed to tell a 1/4" from a 1/2" size? Damned confusing!

 

Regards from Perth

 

Derek 

Posted

Send them back!

Defective for sure ... how is one supposed to tell a 1/4" from a 1/2" size? Damned confusing!

Regards from Perth

Derek

Simmer down Aussie, I'm not worried about telling themall apart now. But when I add a 3/8 and 5/8 into the same drawer, it gets confusing.

Why print the label at all?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.