Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

End grain cutting board

Featured Replies

I have been experimenting making end grading cutting boards which in the end come out quite nice. Here's my question. After my final glue-up, I have squeeze out which is to be expected, and the height of the wood might vary vey slightly which requires sanding. Because of the hardened glue, and the need to sand that out and make flat the entire surface, I've been using a orbital sander with 40 grit disks which takes FOREVER! What's out there where I can take a more aggressive approach knocking down the initial end grain and glue? Through research I know that running end grain through a planer is a no no, so I won't do that.

I just made my first end grain board recently.  I too went the ROS route, I don't have a full size router yet but in the future I want to use a router sled to flatten. 

Let the glue set up partially then scrape it off while it is still soft, it isn't fun but it is better than dealing with dry glue. 

1 hour ago, Michael Melvin said:

I have been experimenting making end grading cutting boards which in the end come out quite nice. Here's my question. After my final glue-up, I have squeeze out which is to be expected, and the height of the wood might vary vey slightly which requires sanding. Because of the hardened glue, and the need to sand that out and make flat the entire surface, I've been using a orbital sander with 40 grit disks which takes FOREVER! What's out there where I can take a more aggressive approach knocking down the initial end grain and glue? Through research I know that running end grain through a planer is a no no, so I won't do that.

Drum sander

p13747.jpg

If you have a big enough air compressor. This should do just fine. An auto-body air file. Find them for about $70.00

 

-Ace-

A router sled will do a pretty mighty fine job flattening both sides of the cutting board, including set up I would even say faster than the drum sander. With that said both are also going to need sand it still as the router will leave track marks and drum sander will leave sending lines so both will cut your standing time down but neither will eliminated. Just remember when sanding The Cutting Boards to change your paper often, trying to squeeze every last minute out of a worn-out pad is futile and frustrating. Change often switch grits quickly going up and down up and down to avoid burnishing the surface

I also found it easier to level the rubber feet I put on the corners rather than get the board completely flat.  None of my knives are completely square so I don't think they will notice the slight twist.  Also found my kitchen counter (old plastic laminate) has a twist compared to the soapstone counter in my bathroom. 

I've made about 6 or 7 end grain cutting boards and have found that running them through the planer with the flattest side on the table works for me. Of course I get tearout on the end pieces, but I finish with on the router table rounding the edges with a round-over bit then using a ROS to finish.

4 minutes ago, drdabrown said:

I've made about 6 or 7 end grain cutting boards and have found that running them through the planer with the flattest side on the table works for me. Of course I get tearout on the end pieces, but I finish with on the router table rounding the edges with a round-over bit then using a ROS to finish.

Probably won't be your practice after you get one that explodes on you.

52 minutes ago, drdabrown said:

I've made about 6 or 7 end grain cutting boards and have found that running them through the planer with the flattest side on the table works for me. Of course I get tearout on the end pieces, but I finish with on the router table rounding the edges with a round-over bit then using a ROS to finish.

I hope you wear a cup. when they go,  metal and wood parts go flying at almost the speed that your pants get soiled..

And I've read a few stories about what happens when end grain gets mixed up with carbide planer cutters. Apparently it's just like end of days.

I had a thin strip come apart in the planer the other day when I was making my cutting board.  That was sketchy enough, Definitely wasn't going to run end grain through the planer after that.  The plastic doesn't seem like it would stop a bullet (planer knife) to me.  I'm thinking of buying a router and making a sled as I'm planning to make a cutting board for my dad for xmas. 

One method I have thought about, but not yet tested: save a few inches of edge-grain glue up and add it to the trailing edge of the board going through the planer. Seems like that would support the edge enough to avoid chipping chunks out of it. Still an unknown risk, though. Notice I said I haven't tried it!

9 hours ago, wtnhighlander said:

One method I have thought about, but not yet tested: save a few inches of edge-grain glue up and add it to the trailing edge of the board going through the planer. Seems like that would support the edge enough to avoid chipping chunks out of it. Still an unknown risk, though. Notice I said I haven't tried it!

That would keep the good part of the board good, but there's still the possibility of chunks breaking off the trailing edge & banging around in the planer, taking out cutters, plastic & flesh

I liked a 3" or 4" belt sander for the initial flattening of the cutting boards. Now I use a drum sander and do it in a fraction of the time with much less effort. Can you get a used belt sander off craigslist for a couple bucks? The belts last much longer than ROS pads if you keep a rubber stick around. 

 

The planer might seem faster until you get tearout thats 1/32-1/16" deep. That is a crap ton of end grain sanding to get rid of the tearout. Ive never done it. I have a byrd head and still wouldnt do it. Yes, i know the russian cutting board professional does it, but hes russian. 

11 hours ago, Pwk5017 said:

I liked a 3" or 4" belt sander for the initial flattening of the cutting boards. Now I use a drum sander and do it in a fraction of the time with much less effort. Can you get a used belt sander off craigslist for a couple bucks? The belts last much longer than ROS pads if you keep a rubber stick around. 

 

The planer might seem faster until you get tearout thats 1/32-1/16" deep. That is a crap ton of end grain sanding to get rid of the tearout. Ive never done it. I have a byrd head and still wouldnt do it. Yes, i know the russian cutting board professional does it, but hes russian. 

He had a video a while back showing his trick  he saturates the end grain with vodka and it is more compliant. 

I've swore off and grain boards until I get a drum sander.  Shannon's new'ish video showing his shop built panel clamps has been bouncing around my head though, and I would think two or three of those clamps would minimize the amount of work to flatten a board.

  • Popular Post

I use the router sled option if my board is very wonky, otherwise I just use a ROS. I do remove glue squeeze out after about 30-60 mins of clamping (Titebond III). However, the biggest difference I have found is in the quality of the sanding paper. I used to use Makita or DeWalt discs just because that was available here. Ever since ordering a sample pack of Mirka discs I haven't looked back. Their 80 grit removes material so much faster and better than the Makita/DeWalt 40 grit with hardly any swirl marks. I now keep only Mirka 80, 150 and 220 in stock and it does it for me. I generally don't even bother with the 150 and jump straight to 220 after flattening. Comes out buttery smooth.

A drum sander is on my future "really really want one" list.

13 minutes ago, Bart said:

I use the router sled option if my board is very wonky, otherwise I just use a ROS. I do remove glue squeeze out after about 30-60 mins of clamping (Titebond III). However, the biggest difference I have found is in the quality of the sanding paper. I used to use Makita or DeWalt discs just because that was available here. Ever since ordering a sample pack of Mirca discs I haven't looked back. Their 80 grit removes material so much faster and better than the Makita/DeWalt 40 grit with hardly any swirl marks. I now keep only Mirca 80, 150 and 220 in stock and it does it for me. I generally don't even bother with the 150 and jump straight to 220 after flattening. Comes out buttery smooth.

A drum sander is on my future "really really want one" list.

Brendon turned me on to the Mirka discs. I'm replacing all grits with it as I need them. They're very aggressive and last longer IMO. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.