Recommended Posts

Posted

@Von, great idea on the false top. I need to remember that. The little 90* angle thingys at the top corners, are they self made or did they come with the ratchet strapping? 

  • Like 1
Posted
On 6/30/2025 at 9:59 PM, Coop said:

 The little 90* angle thingys at the top corners, are they self made or did they come with the ratchet strapping? 

They came with the strap clap. It's made by Pony. Doesn't look like it's made any more but I found one on ebay.

  • Like 2
Posted
On 6/30/2025 at 4:57 PM, Beechwood Chip said:

Installed the Grizzly T34399 dust deflector for my Grizzly G0555 band saw. 

I'm interested in your experiences because dust through the table is a annoyance I have as well.

Yeah, the hose looks like one I would bump all the time as well. With my limited perspective from your photos, does either trying to attach a 45 or 90 adaptor, or maybe drilling and taping the table bottom and replacing the magnets with bolts make any sense?

 

  • Like 1
Posted
14 minutes ago, Von said:

drilling and taping the table bottom and replacing the magnets with bolts make any sense?

You probably have to remove the hose to change blades.

  • Like 2
Posted
15 hours ago, Tpt life said:

Packing and pre-move house beautifying. Ready for that part to be past us. 

Packing a house is a super pain.  Unpacking is no picnic either.  I feel for you. 

Are you moving yourselves or will you use professionals?  Workshop, too?

  • Like 1
Posted
On 7/1/2025 at 8:15 AM, fcschoenthal said:

I've been looking at that for my G0555, so glad to hear it works. I thought about getting one of the Woodcraft 2½" Magfitt sets for attaching the hose to the adapter so it'll stay out of the way when not in use.

That's a good idea, but the magnets holding the thing to the underside of the table are pretty weak.  I had to tweak the hose length and bend to keep the hose from yanking the thing off of the table.  You might find that the Magfitt sets are too heavy.  Check out my more detailed reply to @Von above.

Posted
On 7/1/2025 at 12:55 PM, Mark J said:

This Ripnado thingy may be of interest for bandsaw dust collection.  

Interesting!  It's pretty crowded under the table of the G0555, so I'm not sure that a general solution would fit. 

The T34399 was about $15 with another $15 for the cheapest shipping option.

I think the 3D printed solution might be the best, since it looks like it bolts directly to the insert plate instead of using magnets.  

  • Like 1
Posted
On 7/1/2025 at 12:16 PM, Beechwood Chip said:

I think the 3D printed solution might be the best, since it looks like it bolts directly to the insert plate instead of using magnets.  

It does look like a good option. I downloaded it and will let you know how it turns out.

  • Like 2
Posted
On 7/1/2025 at 1:54 PM, fcschoenthal said:

It does look like a good option. I downloaded it and will let you know how it turns out.

I was thinking of having a 3D printing service make one and send it to me, both to try out the gadget and also to try out using a 3D printing service.  But I'll hold off to see what you think.

  • Like 1
Posted
On 7/2/2025 at 7:27 AM, Von said:

I have to slam the brakes on this endorsement and patting myself on the back. I was adding splines to the box yesterday and noticed two of the corners are opening up, one rather badly. Looking back at the data in my photos, I notice I only had the clamps on for 20 hours, so perhaps I didn't give it the glue enough curing time? In any case, I'm sending the jury back out on this one. I won't get to this today, which will give me a chance to see if it's done separating and then I can figure out next steps. I'm thinking some PVA glue in the joint and re-clamp it.

PXL_20250702_121741504.thumb.jpg.ace2157cf7df0572284d0f79195e4515.jpg

PXL_20250702_121745673.thumb.jpg.91a99386318b4dfe2cd11c891dd9e327.jpg

I've done and seen far worse @Von. Those will probably clean up fairly well with some sanding or planing and possibly some dust and glue if necessary. 

I use Old Brown Glue for that purpose, i find it's much better than pva for mixing with dust and filling voids. 

 

Also, 20 hours is plenty of clamp time. Titebond says 30-60 minutes in Clamps  and not to stress the joint for24 hours. So you're good there. 

  • Like 2
Posted
On 7/1/2025 at 3:33 PM, Beechwood Chip said:

I was thinking of having a 3D printing service make one and send it to me, both to try out the gadget and also to try out using a 3D printing service.  But I'll hold off to see what you think.

I printed it and it looked pretty good, but here are my thoughts

  1. The insert and adapter are held together with 2 printed screws. The printed threads aren't that great and I ended up running a tap to get it cleared out and sized correctly.  Both screws still ended up breaking off in the hole when tightening, so it was a lot of trouble getting the hole cleaned out again. The thread is 1/4-20, so a metal version is advisable.
  2. The adapter outlet is still facing the same way that yours is. I'm not proficient enough in modeling software to change it, but the design would be better facing toward the back and dust port for the same reason you discovered.
  3. It's not easy to take the adapter off and on, which would be required for any blade changes or table tilt. I do like the idea that it's held on by the screws, but is a pain to get changed out.

I'm going to still look around for another 3D printed option, but the Grizzly one (possibly modified with stronger magnets) may still be the best choice for now.

  • Like 2
Posted
On 7/5/2025 at 11:13 AM, fcschoenthal said:
  1. The adapter outlet is still facing the same way that yours is.

I was thinking that with the adapter firmly screwed in place, it would be possible to use a more flexible hose and make a tighter bend down and to the side.  Possibly anchoring the hose in place.

I'll experiment with a 2.5" elbow.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.