legenddc Posted January 21 Report Posted January 21 On 1/21/2026 at 8:41 AM, pkinneb said: I hear you! I lost mine several years ago and have yet to find anything close as a replacement. It's going to add another obstacle. It's not that I don't like the other dealers, but I like to know they have what I need in stock before I drive 3 hours. If I need to rent a truck to pick stuff up I'll have an extra 80 miles to pay for. On 1/21/2026 at 8:44 AM, Von said: I completely get the appeal of having a jig on hand, well-designed and general purpose, that I made and serves me at a moment's notice. I also completely get that one can make a lot of jigs, specific to a job, very quickly. Especially with practice, knowing a a few techniques, and a stash of appropriate scrap on hand. One bit of advice from a local friend: if he saves a jig, he writes his name, the date, and the jig's purpose on it. That's smart to write the date and purpose on it. I sometimes find stuff and wonder what it was for. 2 Quote
roughsawn Posted January 21 Report Posted January 21 On 1/21/2026 at 7:41 AM, pkinneb said: I hear you! I lost mine several years ago and have yet to find anything close as a replacement. Did you contact that sawmill in Cambridge? He sells slabs, not sure about other lumber. 1 Quote
fcschoenthal Posted January 21 Report Posted January 21 On 1/21/2026 at 6:51 AM, legenddc said: Our local hardwood, plywood and cabinetry shop is closing. Now my options are super expensive local places Have you tried local cabinet shops to see where they plan on getting their stock? Quote
Popular Post Tom King Posted January 21 Popular Post Report Posted January 21 I've never had any supplier of dry hardwoods anywhere near me. Today I put the last two new tires on my old trailer in preparation to go get a free 9' Gandy pool table for the rental house a couple of hours away. This new trailer jack takes most of the work out of it. I didn't have to move it much to reach across to the other side. 6 Quote
fcschoenthal Posted January 21 Report Posted January 21 You're finding all sorts of ways to use your new toy. 1 Quote
legenddc Posted January 22 Report Posted January 22 On 1/21/2026 at 1:12 PM, fcschoenthal said: Have you tried local cabinet shops to see where they plan on getting their stock? Not yet. There's another shop just by this place that I could see filling the void. 2 Quote
Popular Post Mark J Posted January 22 Popular Post Report Posted January 22 22 hours ago, legenddc said: That's smart to write the date and purpose on it. I sometimes find stuff and wonder what it was for. Or if I have all the jig's parts. 3 Quote
Mark J Posted January 22 Report Posted January 22 18 hours ago, Tom King said: This new trailer jack takes most of the work out of it. If only you could bring your trailer jack along to pick up (literally) that pool table . Quote
Popular Post Tom King Posted January 22 Popular Post Report Posted January 22 The reason it's free is because it's on the third floor of a beach house. They're going to use that room as another bedroom for a rental house. I'm hiring a pool table moving company to bring it downstairs and load it onto my trailer. I'll set it up myself, but no way did I want to move three 200 pound slates down three flights of stairs. It's a 9' table. They had been trying to sell it but couldn't. I priced renting a telehandler, but the moving company was cheaper and I don't do any lifting. 5 Quote
Popular Post legenddc Posted January 24 Popular Post Report Posted January 24 My dad got his knee replaced today. My mom decided as they were about to be discharged she wanted someone at their house in case my dad needed help so I ran over there. By the time I got there my dad was safely inside. Hung out there for a couple hours while I finished up working. Replaced their microwave door switches again, changed their humidifier filter, and figured out what HVAC filter they needed. Their laundry room door needs the frame patched behind a hinge that’s pulling out. We already tried repairing the screw holes. I think I’ll add a third hinge to the door as well. 37 years of opening and closing with a rack of cans hanging off has been too much. Can’t convince them to put it the cans in their pantry. 4 Quote
Tom King Posted January 24 Report Posted January 24 Can you get some longer screws to go through the jamb and into the framing behind it? 2 Quote
Mark J Posted January 24 Report Posted January 24 I was thinking the same thing. Maybe longer screws, and a 3rd hinge? 1 Quote
gee-dub Posted January 24 Report Posted January 24 +1 on longer screws to hit the studs that frame the door opening. I have had success with this in the past. Don't over-torque the screws and pull the side jamb out of true though . . . DAMHIKT. 2 Quote
legenddc Posted January 24 Report Posted January 24 We tried longer screws but hit nothing. I think I will try to repair the screw holes again before a more invasive repair. I think a painter reinstalled the hinges and I’m wondering if he didn’t overtighten them and strip the holes. 2 Quote
Popular Post Tpt life Posted January 24 Popular Post Report Posted January 24 I have had good success in jambs and doors, with glue and toothpicks. I know it’s a pain, but almost any time I run into issues with a door, I pull the whole thing and rehang it. There are so many issues that correct in the first three steps of hanging a door, that installing out of order keeps you from correcting. Crossleg, lean, swing, square, reveal, etc., have a flow of order that works. 6 Quote
Popular Post gee-dub Posted January 26 Popular Post Report Posted January 26 Started the front yard concrete prep. End result targeted is for my dirt and gravel wasteland to become a horseshoe driveway with extra goodies. Here's the east driveway prep. West (existing) driveway (cracked and ugly, poured in the 1980s) will get demolished and dug tomorrow. 3 Quote
Popular Post Tom King Posted January 26 Popular Post Report Posted January 26 How long were the screws? It's not unusual for there to be a gap between the jamb and framing, but I've never seen a door hung with no framing behind it. The trouble with the screws is that butt hinge screws are no. 9's, so a bit of oddballs' to find, but you can get them off Amazon in different lengths. I would try some 4" ones. 3 Quote
Popular Post legenddc Posted January 26 Popular Post Report Posted January 26 I will have to see what I have in my stash and what my dad has. I'm not sure when I'll get it fixed. I need to time it right so my dad doesn't try to help with his recovering knee. I think the last time I started fixing the door and then he finished "fixing" it. 3 Quote
Popular Post gee-dub Posted January 26 Popular Post Report Posted January 26 Helping a buddy move his garage fixtures to a new shed building on the property. We came across this that he had all but forgotten about. I swear the thing looks like the day he brought it home from Radio Shack. 6 1 Quote
wtnhighlander Posted January 26 Report Posted January 26 I used to do some side hustle work for a guy that ran his business on a TRS-80. 1 Quote
Tpt life Posted January 27 Report Posted January 27 I played programming with one in elementary school. 2 Quote
Von Posted January 27 Report Posted January 27 That's an amazing find. Part of a trinity with the Apple IIe and Commodore 64. 2 Quote
Popular Post fcschoenthal Posted January 27 Popular Post Report Posted January 27 I learned some BASIC programming on the Model I (with cassette) and then the Model II with the 8" floppy disks. Also played with the Apple IIe. Looking back, It's funny how everyone was vying for their version of DOS to be the standard. 3 Quote
Mark J Posted January 27 Report Posted January 27 14 hours ago, gee-dub said: Helping a buddy move his garage fixtures to a new shed building on the property. We came across this that he had all but forgotten about. I swear the thing looks like the day he brought it home from Radio Shack. That is probably worth some good money to a collector. 2 Quote
gee-dub Posted January 27 Report Posted January 27 On 1/27/2026 at 3:51 AM, fcschoenthal said: I learned some BASIC programming on the Model I (with cassette) and then the Model II with the 8" floppy disks. Also played with the Apple IIe. Looking back, It's funny how everyone was vying for their version of DOS to be the standard. It's like VHS vs. Betamax, optical vs. capacitive discs, HD vs. Blueray video discs; new technologies battle to be the new standard and somebody wins 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.