Tpt life Posted April 22 Report Posted April 22 On 4/22/2026 at 10:48 AM, legenddc said: This will be the 3rd set of rear brakes I've put on our 2014 Mazda CX-5 that only has 81k-ish miles on it. The set before this were replaced because the rear passenger brakes seemed to be sticking. Despite being thoroughly cleaned and lubricated, it looks like the lower pin stuck and it chewed through the pad in 13-14k miles. Someone I saw online was comparing rears to fronts on newer vehicles. Rear pads were failing due to being thinned out. Fronts used to get swapped twice as often as rears, so the started creating failure into the rears. That said, if you ever had rotors replaced, be sure all mating surfaces got clean. If not, runout can occur that creates friction heat due to the rotor and pads being out of plane. 2 Quote
Popular Post legenddc Posted April 22 Popular Post Report Posted April 22 On 4/22/2026 at 12:04 PM, Tpt life said: Someone I saw online was comparing rears to fronts on newer vehicles. Rear pads were failing due to being thinned out. Fronts used to get swapped twice as often as rears, so the started creating failure into the rears. That said, if you ever had rotors replaced, be sure all mating surfaces got clean. If not, runout can occur that creates friction heat due to the rotor and pads being out of plane. I just watched a video of a mechanic saying the same thing. I think our car uses the rear brakes more for the traction control so they get used without us even knowing. We do mostly city/heavily congested suburban driving too. Saw a local tire chain shop charges $525 for new pads/rotors. I'm under $500 for 3 sets of pad/rotors and a new caliper. 3 Quote
Popular Post gee-dub Posted April 23 Popular Post Report Posted April 23 Went to my daughter's this morning and played with the new grandson for a couple of hours. He is just starting to walk. Then my daughter went and picked up the next oldest grandson from school and we all went to a local sandwich joint for Italian Grinders and macaroni salad. Picked up a Grinder to go for oldest grandson who was still in school and didn't get to come along. Dropped the daughter, grandsons, and extra sandwich off at home. Then LOML and I came to our home with full bellies and took a nap. It was a good day. 5 Quote
Coop Posted April 23 Report Posted April 23 I’ve said for years that the auto industry has enough snap to replace the damn metal squealer that the driver can’t hear but just annoys the driver next to you. My 2010 Silverado now shows the mileage left on each pad. Should help in having to replace the rotors. 2 Quote
Popular Post legenddc Posted April 25 Popular Post Report Posted April 25 Replaced the brakes today at my parents house while my daughter was at dance rehearsal. Took a while to get the one caliper off. Cleaned the wheel hub and made sure everything was lubricated. Had to leave halfway though to pick up my daughter in my Mom’s car. 4 Quote
Popular Post Tom King Posted April 26 Popular Post Report Posted April 26 I finally finished installing all the floor joists for the barn apartment. This was a much worse job than building a new house since there was so much stepping over, in and out than working on a new house where you can get around everything-especially by myself. I had saved all the strips of sapwood that I ripped off of Cypress boards when making Cypress shingles, not knowing that I would ever have a use for them. I'm using them to hold 2" foam sheets which supports R23 Rockwool batts between the floor joists. The barn has a lot of overhang and good drainage around it, so the ground inside is always bone dry. I laid 20 mil crawlspace vapor barrier over it anyway. The North wall on the outside will be completely closed up underneath but the long side on the aisleway will be wide open with removable screen panels. It's a slow go by myself, but once I get the floor done it shouldn't be so bad. I have the floor insulated, subfloor down and all closed up where the bedroom will be. It's good to have just that flat floor to be able to work on top of. I have to give my knees days off from all the high stepping over floor joists. I'm very glad to get them all in. Next step is to get the DWV piping in for the bathroom because I won't be able to get under that part of the floor that is only about a foot off the ground. Water piping will be run in black poly pipes with an access panel in the wash stall on the end, so I can change any of it in the future. The bathtub is against the aisleway where there is a big hay drop door that I will leave to have access to the water lines in the future. It's been especially slow over the past few weeks because we had two litters of puppies going to their forever homes, and three more litters born over the past week and a half. Only recently have I had time to work on this project. Total size for the apartment is 12 x 40. Our farrier has been spreading word for us without me asking him to and we're already getting people who want to rent the horse farm. I have so many projects going that I have no idea when this will be done, but it will give me something to do this Summer when renters are here for the Lake House. 7 Quote
Popular Post Von Posted April 27 Popular Post Report Posted April 27 I enjoy watching bats fly around at dusk. They seem to come and go (and there have been population concerns here). I saw them again recently and it prompted me to put this bat house up on the new shed in the sunniest spot I could find (I understand they like the warmth). It was up before for a couple of years before re-siding prompted me to take it down and never had a tenant but I'll give it another shot. 4 Quote
Popular Post Mark J Posted April 28 Popular Post Report Posted April 28 We just purchased and put up a couple of bat houses ourselves. Someone told us to hang it in tree, which is what we did. 3 Quote
Popular Post gee-dub Posted April 29 Popular Post Report Posted April 29 Random complaint . . . I made a tall boy and a low boy dresser for our old master bedroom years ago. I get four of those sixteen drawers. I made two seven drawer dressers for the new master bedroom. I get one sock drawer out of those. We have an old master bedroom closet in which I have not one stitch of clothing. I get six feet of closet rod in the bedroom/office. There is a nine foot by ten foot walk in closet in the new master bedroom. I get about ten feet of rod in there but part of that is taken up with file storage and home defense. I went looking for a pair of grey Carhartt shorts to wear to lunch today and it took me fifteen minutes to find them. They were not in the "shorts" drawer. Before I end my rant I just want to ask . . . where is the justice in this world!?! 5 Quote
Popular Post Tom King Posted April 29 Popular Post Report Posted April 29 When I built the new bedroom/bathroom addition onto our house around 2004, I built two 8x16 "closets". One of them is mine. Pam said when we were planning it that one closet that big would be enough. I said, "Nope". 3 Quote
wtnhighlander Posted April 29 Report Posted April 29 @gee-dub, your next project should be a nice armoir, that 'accidentally' gets made too large to leave the shop. Quote
Popular Post Ron Swanson Jr. Posted April 29 Popular Post Report Posted April 29 On 4/29/2026 at 1:41 PM, gee-dub said: Random complaint . . . I made a tall boy and a low boy dresser for our old master bedroom years ago. I get four of those sixteen drawers. I made two seven drawer dressers for the new master bedroom. I get one sock drawer out of those. We have an old master bedroom closet in which I have not one stitch of clothing. I get six feet of closet rod in the bedroom/office. There is a nine foot by ten foot walk in closet in the new master bedroom. I get about ten feet of rod in there but part of that is taken up with file storage and home defense. I went looking for a pair of grey Carhartt shorts to wear to lunch today and it took me fifteen minutes to find them. They were not in the "shorts" drawer. Before I end my rant I just want to ask . . . where is the justice in this world!?! This sounds very familiar. If i ever complain about the grossly unfair distribution of closet and dresser space, my wife will just say "You're lucky i allow *you* to be in here" I just take my lumps on this unwinnable battle. 3 Quote
gee-dub Posted April 30 Report Posted April 30 On 4/29/2026 at 2:37 PM, Tom King said: When I built the new bedroom/bathroom addition onto our house around 2004, I built two 8x16 "closets". One of them is mine. Pam said when we were planning it that one closet that big would be enough. I said, "Nope". Wiser words were never spoken Quote
Coop Posted April 30 Report Posted April 30 I guess I’m luckier than most. My three pair of cargo shorts and five tee’s fit nicely in my drawer. Whitey tighties and socks have ample room in the small tote that slides under the bed. 2 Quote
Popular Post Von Posted April 30 Popular Post Report Posted April 30 A quick tip, in case it's helpful to someone else.... A break in my bench-building to make a picture frame for a family member and I was reminded I'm grateful for learning (probably from this forum) about the power of shims to make minor adjustments to stops. In this case, I cut the piece intentionally long, measured how much shorter it needed to be and then used an appropriate shim (a Rockler 5/16" set up block in this case) to dial in the length. If I were going to make lots of cuts based on the stop, I would move it to idiot-proof things, but for just two cuts, I find it faster and more accurate to use a shim rather than move it. 6 Quote
Chet Posted April 30 Report Posted April 30 On 4/29/2026 at 11:41 AM, gee-dub said: where is the justice in this world!?! Probably stored in your wife's closet under lock and key. 2 Quote
Popular Post gee-dub Posted April 30 Popular Post Report Posted April 30 I have a few leather splits on had for leather work when required. LOML has decided on the dark brown suede for the straps. I sanded the top film on the mirror frame this morning to provide a smooth landing strip for the final top coat. I am leaning towards a semi-gloss lacquer final top coat. I usually use a paste wax but this will be on the wall behind the sideboard and hard to reach. I want something a little more durable so I don't have to think about it. It is funny how many decisions in my later life revolve around "is there a way I can make this easier to maintain in the future?". 6 Quote
Popular Post Chet Posted April 30 Popular Post Report Posted April 30 On 4/30/2026 at 1:07 PM, gee-dub said: "is there a way I can make this easier to maintain in the future?" This reminds me of my mom in the senior section of her life. She started telling family members that she didn't want any birthday or Christmas gift that would require dusting. 4 2 Quote
gee-dub Posted May 1 Report Posted May 1 On 4/30/2026 at 2:04 PM, Chet said: This reminds me of my mom in the senior section of her life. She started telling family members that she didn't want any birthday or Christmas gift that would require dusting. Amen. When I show LOML certain furniture designs she will simply say . . . "Dust Magnet" . . . and the design process continues. 2 Quote
legenddc Posted May 1 Report Posted May 1 On 4/30/2026 at 8:33 AM, Von said: A quick tip, in case it's helpful to someone else.... A break in my bench-building to make a picture frame for a family member and I was reminded I'm grateful for learning (probably from this forum) about the power of shims to make minor adjustments to stops. In this case, I cut the piece intentionally long, measured how much shorter it needed to be and then used an appropriate shim (a Rockler 5/16" set up block in this case) to dial in the length. If I were going to make lots of cuts based on the stop, I would move it to idiot-proof things, but for just two cuts, I find it faster and more accurate to use a shim rather than move it. It just so happens I ordered a setup block kit earlier today. I will have to keep this in mind. On 4/30/2026 at 5:04 PM, Chet said: This reminds me of my mom in the senior section of her life. She started telling family members that she didn't want any birthday or Christmas gift that would require dusting. My grandfather once emailed his kids to say they wanted a 1/2 cord of firewood for Christmas as they were out of space to put fishing or lake related gifts. He had us split some logs from a tree that fell so he sent an updated email saying 1/4 cord would be fine. 2 Quote
legenddc Posted May 1 Report Posted May 1 Took today off to chaperone my daughter’s 5th grade class field trip. Had to not lose five 11 year old girls at the Natural History Museum. My daughter was not happy her friends didn’t want to do the scavenger hunt and wants to go back and do it. Ran to our dump to get rid of the brake parts and recycle some glass and clothes. Apparently we can get free plants there so I have 3 of some sort of plant. Will have to figure out what they are before I plant them. Waiting to pickup my son from school now. 2 Quote
Popular Post gee-dub Posted May 5 Popular Post Report Posted May 5 So LOML wanted a "pot filler". Well pretty much my life-goal is to make her happy so we got one. When I first heard about it I thought I had never heard of anything more silly . . . wrong! For pasta, soups, sauces, corn on the cob . . . the thing rocks. Same goes for the "solar tube" in the kitchen and the bathroom. Our electric bill has dropped drastically. She's right again!?! Then just as a side note . . . uncharacteristic May weather for our part of town. Cloudy and overcast!?!. How often does that happen around here? 6 Quote
Popular Post legenddc Posted May 5 Popular Post Report Posted May 5 Firetrucks are leaving now. Apparently a new neighbor (renter) was having a campfire in their backyard and added leaves to it. Their next door neighbor came home to a house filled up with smoke. It seems when you're a mile from the fire station and next to an almost 500 acre park you get a lot of people responding. At my in-laws this weekend for a housewarming party. One of their new neighbors fell and we ended up calling 911. Turns out she fractured her kneecap. Outside of dealing with first responders, I've been finessing the fitment of the cabinet doors. Need one more slightly trimmed and I think it will be time to sand and paint anything that got trimmed or damaged. 3 Quote
Mark J Posted May 5 Report Posted May 5 11 hours ago, gee-dub said: Same goes for the "solar tube" in the kitchen and the bathroom. Our electric bill has dropped drastically. She's right again!?! That's surprising, not the part about her being right, but that cutting back on lighting use would have such a significant effect on your bill. I would have thought HVAC to be the biggest power consumer. 1 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.