Popular Post gee-dub Posted May 16 Popular Post Report Posted May 16 Took the grand kids out to lunch at a family place one town to the south. That place shares a parking lot with one of my favorite BBQ places to I walked over and got a rack of baby-backs. So good. You know the kind where the meat practically falls off the bone and you don't even really need to chew . . . ahhhhh. 3 Quote
Popular Post wtnhighlander Posted May 16 Popular Post Report Posted May 16 I wrapped up a new small parts joinery sled for my tablesaw. Hold downs and stops all made from junk I needed to clear out. 8 Quote
fcschoenthal Posted May 16 Report Posted May 16 I use my big sled a lot, but sometimes it just makes more sense to have a smaller one. 2 Quote
Popular Post gee-dub Posted May 16 Popular Post Report Posted May 16 On 5/16/2026 at 8:59 AM, fcschoenthal said: I use my big sled a lot, but sometimes it just makes more sense to have a smaller one. Amen. I have a selection. Some with t-track, some with Micro-Jig dovetails, some deep, some wide. Handy little buggers. 3 Quote
Von Posted May 16 Report Posted May 16 On 5/16/2026 at 10:08 AM, wtnhighlander said: I wrapped up a new small parts joinery sled for my tablesaw. Hold downs and stops all made from junk I needed to clear out. Nice looking sled. You cut your own t-slots or what are those hold downs using? TIA 1 Quote
Popular Post Tom King Posted May 16 Popular Post Report Posted May 16 That sled not only looks like it's very functional, but looks good too! I finished up the under floor plumbing this morning. The most amazing thing about this plumbing job was that it only took one unplanned trip to Lowes. Hard to believe I forgot that trap adapter, but all the plans were in my head, so my head must be falling off a bit. I securely set a tailpiece in the exact location to fit everything else to. It really wasn't that bad to get done. The main 4" line will have a cleanout easily accessible in the aisleway behind the old hay drop door. Pipes stubbed up through the plate. Next step is to insulate that section and put the last piece of subflooring down so I can fasten the plate down and build the last wall in that bedroom, but I'm tired of messing with it today. I thought I was going to end up having to build the vanity for that bedroom, but Pam found the perfect one at the Habitat store this morning for $30. My first PEX expansion fittings. I love this system just after these two joints. All to code with combination Wye's and long sweep 90's where they're supposed to be. 5 Quote
wtnhighlander Posted May 16 Report Posted May 16 @Tom King, oblyone extra trip would be an absolute miracle for me! I wish I had found someone like you to learn these tips from earlier, before I decided DIY plumbing was something I never wanted to do again. Quote
wtnhighlander Posted May 16 Report Posted May 16 1 hour ago, Von said: Nice looking sled. You cut your own t-slots or what are those hold downs using? TIA Base is 3/4" ply. Slots are 1/2" wide x 3/8" deep grooves on the bottom, with 1/4" through slots centered in them. All cut on the router table. I used 1/4-20 all thread, square 'washers' (cut from cheap angle brackets) and hex nuts glued on with JB Weld for the bolts. Had to grind away about half of the nut thickness to avoid dragging the table. Knobs are just Tee nuts epoxied into some hole-sawn rounds. The flat knobs have wing nuts embedded, which took a little dril & knife work. This is a cheap way to make hold-down track, but has the disadvantage of dropping bolts to the table when tension is released. I might improve by opening holes from the top, at the end of the slot, so the bolt 'head' can insert from above. Then the sled bottom could be skinned with something to keep the bolts from scratching the table. Thanks for making me think of that! Also, if you can get by with 3 or 4" pan head machine screws, grinding the thickness away might not be necessary. I needed at least 5" bolts due to the thickness of my clamps and knobs. 1 1 Quote
Popular Post legenddc Posted May 16 Popular Post Report Posted May 16 Cut down an 8’ pine tree this morning that’s been taking over our backyard. Had to pause to go to my son’s flag football game. They finally seem to be getting it. He had 5 “tackles”. Finished up the tree removal and dug a hole for a hackberry bush (I think). We wanted it right where a massive tree root was. Took me a while with a digger bar, recip saw and an ax to get enough of the root out. Went to the pool since a couple are open. Put away some tools when we got back home. My neighbor returned my miter saw. Ate hot dogs and hamburgers on the deck before going to our basement and starting Pirates of the Caribbean with our kids. Thankfully, they’re tired and ready for bed now! 4 Quote
Popular Post Tom King Posted May 17 Popular Post Report Posted May 17 I don't have any tips or tricks for plumbing. Installing new work is infinitely easier than working on old plumbing. It's all just what are you willing to accept. I want all slope to be exactly 1/8" a foot, indicated by a Johnson level with slope graduations or digital level. All pipes cut with RAS or miter saw to be perfectly square ends and always seated all the way home with plenty of primer and glue. Sanitary tees and regular elbows only installed in one position with vertical drop from turn. Every other turn a long sweep. Stainless steel toilet flanges through bolted to water resistant subflooring with SS fasteners. All water supply lines accessible and easily replaceable. It's much easier starting with some you can get to. When I designed new houses, every bathroom or kitchen was over an unfinished utility/storage room with the water lines going up through the floor that you could get to. This job was the first time I ever had to precisely locate anything like that tub trap because there would be no access later. It was the first time I ever fastened down a pipe to key off of. I didn't figure that out in advance. It just came to me the morning I starting putting the pipes together after locating the position it needed to be in. 5 Quote
Popular Post pkinneb Posted May 17 Popular Post Report Posted May 17 Got the new J/P wired up and tested today. A few minor tweaks and the results are impressive! I bough this machine for a few reasons the main one being the spiral head, right behind that was that the newer version folds straight back in one piece unlike my older A3/31 which kinda gull winged one side at a time. Finally I was hoping it would be quieter, the old one was really load LOL. Well I can say I hit on all three items it really is just a better version of what I have used for the last 20 years, so glad I finally pulled the trigger 9 Quote
Popular Post Tom King Posted May 20 Popular Post Report Posted May 20 Fixed a stopped working completely heat pump in the rental house just now. Yesterday afternoon we discovered it wasn't working. I thought maybe it was the capacitor, and have a couple on hand, but the cap was fine. Probed around to check voltages and was getting nothing between L1 and L2, which should have been providing 240V. Checked each leg to ground and there was 120 on each. Same at outside disconnect and disconnect on inside air handler. Old breaker was sending 240V somewhere like it was supposed to, but had never tripped. It was dark when I quit working on it yesterday, but this morning I was trying to decide whether to pull a whole new wire or crawl into the almost impossible attic with rough cut heavy trusses. I decided I'd go back in there a little ways to see if there was a junction box anywhere. Fortunately, not too far back in there I found the problem. There was a connection like is supposed to be in a junction box, but the wires were out in the open put together with split bolts. One split bolt was welded solid to one of the wires and the wire was burned in two. This house was considered a tear down when we bought it, but it almost burned down on it's own. Thankfully there was plenty of slack in the wire to be able to get back to good wire on both sides. I did put the cover back on that junction box but wanted to get out of the 120 degree attic as quickly as I could, so I didn't take any more picture. back together like it should have been to start with, and the AC went right to blowing cold air. 2:00 now and first guests for the year coming at 5. I worked harder than I like to today, but glad it all worked out pretty simply. I'd like to put off until cool weather to replace the whole 20 year old system. This was a good luck electrical fix. It required no trips to stores. I keep some extra stuff on hand and was glad I had that junction box and a large enough split bolt. I would have rather used a Burndy, but didn't have one big enough, so this will be okay and certainly better than it has been for 20 years. 7 1 Quote
wtnhighlander Posted May 21 Report Posted May 21 That was a close one, Tom! Glad it opened the circuit instead of arcing until a fire started. 2 Quote
fcschoenthal Posted May 21 Report Posted May 21 I'm always amazed at what some people will do thinking that they're fixing the problem. Quote
legenddc Posted May 21 Report Posted May 21 Always shocking what steps are cut at times by people. Yesterday I finished up the construction on the cabinet that I'm making. At least what is needed to make it functional. I still need to touch up the paint, make the side panels and install the crown molding. That can wait until I get around to it. My wife has already started sorting stuff to determine what goes where and what gets donated. 2 Quote
Popular Post Botch Posted May 21 Popular Post Report Posted May 21 I changed out my furnace filter and the new one had an odd, 3" gold-colored disk on it; I read the wrapper and I was to pull a paper strip from the disk, download their App to my phone, and connect via Bluetooth. So now my furnace filter is going to send me a notification when it gets dirty. That is borderline ridiculous, but does explain why it was a bit pricey (it was the only 16x20 Ace had in stock at the time). Think I better go back to Home Despot and buy another 6-pak of $4 filters. 4 1 Quote
Popular Post fcschoenthal Posted May 21 Popular Post Report Posted May 21 On 5/21/2026 at 2:44 PM, Botch said: So now my furnace filter is going to send me a notification when it gets dirty. My thermostat lets me know when it's time for a change. I still mark the date on the filter when I change it and check when it's getting close. Mine are 4" thick, so I only change about every 6 months. 3 Quote
Popular Post Mark J Posted May 22 Popular Post Report Posted May 22 Someday someone is going to come up with a "smart" coffee cup that sends a message to my phone to let me know when it's empty. 4 Quote
Tom King Posted May 22 Report Posted May 22 My excavator sends me an email every night that tells me where it is by street address, how many hours it worked that day divided by work time and idle time (it idles down automatically when it's not working), the diesel fuel level, oil level, and hydraulic fluid level. There are 3d grading programs that you can tie into the machines computer that follows the 3d plan by just pulling on one stick, including changing the angle on a tilt bucket. I don't have anything that fancy but do have a dual slope laser with a receiver that clamps onto the stick using a strong magnet with a string of LED lights that indicates if you are on the laser line, above it , or below it. I think pretty soon you will be able to email the job to the machine and it will go do it while you sit at home. It's getting easier and cheaper for them to do this all the time, like the chip on the HVAC filter. 2 Quote
Tpt life Posted May 22 Report Posted May 22 I’d want the cup to let me know if the coffee was getting cold. 2 Quote
Ron Swanson Jr. Posted May 22 Report Posted May 22 On 5/22/2026 at 7:33 AM, Mark J said: Someday someone is going to come up with a "smart" coffee cup that sends a message to my phone to let me know when it's empty. As someone who drinks WAY too much coffee, I fully support this initiative! 1 Quote
Popular Post gee-dub Posted May 22 Popular Post Report Posted May 22 Reviewed the watering schedule (or lack thereof) for the Plumarias we cut back hard in early spring. The toppings are coming back like gang busters. 3 Quote
Popular Post wtnhighlander Posted May 23 Popular Post Report Posted May 23 9 hours ago, Tpt life said: Is want the cup to let me know if the coffee was getting cold. https://www.amazon.com/wifi-coffee-mug/s?k=wifi+coffee+mug 3 Quote
Popular Post Botch Posted May 23 Popular Post Report Posted May 23 (edited) I try not to post on this thread too much, but I spent a few hours today watching Porch Pirate revenge, and my stomach hurts from laughing! https://youtu.be/zzSvZC4Jh0U?si=L1wQpYw6cQokIj30 https://youtu.be/0VEgIbhA9_o?si=4901WL9_CPjYXNaP Some observations: - 90+% of porch pirates (PP) are obese - The packages with slightly longer det times, so the packages go off inside the thief's car, are Primo! - An Amish guy who ends up spooking his horse, and buggy, thru a barbed wire fence, YESSS!!! - Calling the cops, just What Level Stupid are you?!?!? - Calling your own HOA, where both you and your victim are members, just What Level Stupid Squared are you?!?!? EDIT: I was told by folks smarter than I that most of these are AI-generated (also makes sense that blowing paint and glitter into others' eyes is a good way to get sued). Mea culpa. Edited May 24 by Botch Correction 1 3 Quote
Popular Post gee-dub Posted May 23 Popular Post Report Posted May 23 I love the ones where they call the cops on themselves. Oldest grandson spent the night; pizza, movies, and all that. 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.