Lee Bussy Posted December 5, 2015 Report Posted December 5, 2015 I read Marc's article about 6" vs 8" and it sounds like I want a 6". That decided, which brand? I was hopping around Amazon and think the following is pretty representative of the range of blades:Forrest DK06244 Dado King 6-Inch 29/32-Inch Width 5/8-Inch Bore Dado Blade Set - $279.00Freud SD606 6-Inch Dial-A-Width Dado - $233.58Freud SD506 6-Inch Super Dado Set with Anti-Kickback Design $165.12Freud SD206 6-Inch Professional Dado $73.50Oshlun SDS-0630 6-Inch 30 Tooth Stack Dado Set with 5/8-Inch Arbor $72.68It seems like Forrest is a very popular manufacturer, at least for the WWII blades. I'd prefer not to spend that much if I don't have to. I expect the majority of my dado usage will be for M&T and some plywood dados.I mean yes, I am looking for someone to tell me I can spend $73 instead of $279 - and I know I'll find that. But if I do go lower, what am I missing/cursing? Quote
Trip Posted December 5, 2015 Report Posted December 5, 2015 (edited) ==>I read Marc's article about 6" vs 8" and it sounds like I want a 6"Well, that's one opinion...I'd go 8" if you care about the quality of your cuts... For DIY, yea 6" is fine... Edited December 5, 2015 by hhh Quote
Lee Bussy Posted December 5, 2015 Author Report Posted December 5, 2015 I'm not sure my little jobsite saw can swing an 8" stack. Quote
Trip Posted December 5, 2015 Report Posted December 5, 2015 (edited) ==>Jobsite sawI'm not sure jobsite saws have arbors long enough for a stack... And if they do, then enough power to spin them... Check the manual for restrictions... Edited December 5, 2015 by hhh Quote
Lee Bussy Posted December 5, 2015 Author Report Posted December 5, 2015 ==>Jobsite sawI'm not sure jobsite saws have arbors long enough for a stack... And if they do, then enough power to spin them... Check the manual for restrictions...from the manual (R4510): Quote
Trip Posted December 5, 2015 Report Posted December 5, 2015 So the dial-a-dado from your list is out...From your list, I've got the Dado King and the Super Dado. Both are good. The King leave a better cut and can be reshaprened more times... Quote
Cliff Posted December 5, 2015 Report Posted December 5, 2015 I like the Oshlun. But I've only used the Oshlun. 1 Quote
ChrisG-Canada Posted December 5, 2015 Report Posted December 5, 2015 I have the Freud Super Dado 8" set. Works good for me.I debated (with myself ?) between the Freud and the Dado King - In the end I went with the Freud (cheaper) and I get clean, accurate cuts.The Dado King may be a better set but I don't cut dados very often and so far I don't regret buying Freud. Quote
Cliff Posted December 5, 2015 Report Posted December 5, 2015 ==>I read Marc's article about 6" vs 8" and it sounds like I want a 6"Well, that's one opinion...I'd go 8" if you care about the quality of your cuts... For DIY, yea 6" is fine...What makes an 8" better cut quality? Wouldn't it only affect how deep you cut? Quote
estesbubba Posted December 5, 2015 Report Posted December 5, 2015 Might not work for your saw but this is a good dado currently $90 with the current promotion:http://www.amazon.com/gp/product/B0002ZU6X4?keywords=dewalt dado set&qid=1449335558&ref_=nav_ya_signin&s=hi&sr=1-1 Quote
Trip Posted December 5, 2015 Report Posted December 5, 2015 (edited) ==>Wouldn't it only affect how deep you cut? No. As Eric pointed-out, I'm doing double duty... So I'll be channeling Don for awhile and just giving answers -- not explanations... Edited December 5, 2015 by hhh 1 Quote
mat60 Posted December 5, 2015 Report Posted December 5, 2015 I have had many but right now I was in a pinch so I grabbed a 8in Dwalt on sale and it will get me by.I liked my Freud....I bet I didn't spell that right Quote
Boatworks Today Posted December 5, 2015 Report Posted December 5, 2015 I picked up a Dadonator (I know, goofy name) this past Summer from Ebay (was new, but much less expensive than getting it from a store) and it cuts beautiful. They also make a 6", but it's still $200 :-/..I think I got mine for $120 give or take? Keep an eye out on ebay, occasionally they have one listed. Quote
Tpt life Posted December 5, 2015 Report Posted December 5, 2015 (edited) What makes an 8" better cut quality? Wouldn't it only affect how deep you cut? This may not be the right answer here, but use this as fuel to use in your search. 8" teeth move faster at the same RPM being further away from center. 8" teeth intersect the table at a shallower arc. High end commercial manufacturers are not building 6" sets for anyone but hobby shops. Edited December 5, 2015 by C Shaffer 2 Quote
shaneymack Posted December 5, 2015 Report Posted December 5, 2015 Might not work for your saw but this is a good dado currently $90 with the current promotion:http://www.amazon.com/gp/product/B0002ZU6X4?keywords=dewalt dado set&qid=1449335558&ref_=nav_ya_signin&s=hi&sr=1-1 I have the same one Mike and I'm really happy with it. Sent from my SM-P550 using Tapatalk Quote
Cliff Posted December 5, 2015 Report Posted December 5, 2015 This may not be the right answer here, but use this as fuel to use in your search. 8" teeth move faster at the same RPM being further away from center. 8" teeth intersect the table at a shallower arc. High end commercial manufacturers are not building 6" sets for anyone but hobby shops. well damn, wish I had known that 6 months ago. Ha. Quote
Tpt life Posted December 5, 2015 Report Posted December 5, 2015 There is so much in wood working that is not a simple good vs bad. If your 6" does the job, don't feel regret or envy. Don't read everything in my post as a qualitative remark as much as a quantitative. Too many just don't engineer in three dimensions often. 2 Quote
Llama Posted December 5, 2015 Report Posted December 5, 2015 I think the 8" is better due to the angle the blade approaches the piece being cut. 1 Quote
Immortan D Posted December 5, 2015 Report Posted December 5, 2015 An 8" blade has a faster linear speed and more teeth. May have something to do with cut quality. Quote
andrew-in-austin Posted December 5, 2015 Report Posted December 5, 2015 When the time comes for me, I will be getting the ridge carbide 8" dado. Holbren usually has the lowest price. Quote
knotscott Posted December 12, 2015 Report Posted December 12, 2015 The Infinity Dadonator Jr should rival, if not exceed the performance of the Forrest, but at a more reasonable price (~$200). As expected, both the Forrest and the Infinity will have better performance than the Oshlun or Freud 206, but all will do a decent job. If you're willing to go with an 8" set, the Dewalt/Delta 7670 will also outperform the Oshlun and SD206 for ~ $120, though it's not quite as good as the premium sets. It also has a great carrying case and excellent shim stock. Quote
Lee Bussy Posted December 13, 2015 Author Report Posted December 13, 2015 The Infinity Dadonator Jr should rival, if not exceed the performance of the Forrest, but at a more reasonable price (~$200). As expected, both the Forrest and the Infinity will have better performance than the Oshlun or Freud 206, but all will do a decent job. If you're willing to go with an 8" set, the Dewalt/Delta 7670 will also outperform the Oshlun and SD206 for ~ $120, though it's not quite as good as the premium sets. It also has a great carrying case and excellent shim stock.I'd heard that of the DeWalt. Thing is this saw won't swing an 8". Too bad because that price is right.I'll add the Dadonator to the list. Quote
miranthis Posted December 15, 2015 Report Posted December 15, 2015 So, what is the arbor length that the stack requires? I have an old Craftsman (Emerson) 113.29902 and it has a pretty long arbor shaft.....I have a copy of the manual and it covers dado stacks, but not the max width. Also, its a 1967 saw, so I suppose the 6 in is the better stack given my low power? What do you think? Jeff in KC Quote
bgreenb Posted December 15, 2015 Report Posted December 15, 2015 +1 for the dadonator. Beautiful cut quality. Been very happy with it. Quote
Lee Bussy Posted December 15, 2015 Author Report Posted December 15, 2015 So, what is the arbor length that the stack requires? I have an old Craftsman (Emerson) 113.29902 and it has a pretty long arbor shaft.....I have a copy of the manual and it covers dado stacks, but not the max width. Also, its a 1967 saw, so I suppose the 6 in is the better stack given my low power? What do you think?Do you have a set of calipers? Take the blade off, put the washer and nut back on and get full engagement - then measure. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.