Popular Post h3nry Posted March 27, 2025 Author Popular Post Report Posted March 27, 2025 I've now started work on the cabinet doors. Cutting the rails and stiles to size and ploughing a groove for the panels. These are cut from 8/4 stock that I sawed about 1/2" off to make the drawer sides. The stiles will stay this thickness to stand proud, but the rails will need to be planed a little thinner. Then some mortise and tennons to build the frames ... I've opted to make through tenons. These doors will have to support the top when it is unfolded, and if somebody leans on the table they may need to hold significant weight, and I don't want them racking. The front will have three panels, and because I want extra workspace on the left when the top is unfolded ... the left hand door will have two of them. An extra stile needs to be inserted into the frame. This is done with a half-lap joint: Everything is a nice tight fit ... Now I have to work on shaping and carving the rails ... The lower rails will be very similar to the cabinet sides ... but I'm not quite sure what I'm going to do with the top rails yet. 7 Quote
gee-dub Posted March 28, 2025 Report Posted March 28, 2025 This is such a satisfying ride-a-long. Again, thanks for taking us with you. 2 Quote
Mark J Posted March 28, 2025 Report Posted March 28, 2025 Sounds like you will need some heavy duty hinges to support the top open load. But that's down the road a bit. Quote
h3nry Posted March 28, 2025 Author Report Posted March 28, 2025 On 3/28/2025 at 8:28 AM, Mark J said: Sounds like you will need some heavy duty hinges to support the top open load. But that's down the road a bit. I'm going to be using piano hinges ... I hope they'll be up to the task. 1 Quote
Popular Post fcschoenthal Posted March 28, 2025 Popular Post Report Posted March 28, 2025 It's really nice to see such great work done with hand tools. I sometimes wish I had the patience to make something that way, but you make it look so effortless. 3 Quote
Popular Post h3nry Posted March 30, 2025 Author Popular Post Report Posted March 30, 2025 Managed to get the rails shaped. Cutting the shape into the top rails removed the groove for the panel, so I had to recut it with some chisel work ... And ready to start the carving process... 6 Quote
wtnhighlander Posted March 30, 2025 Report Posted March 30, 2025 Looking great, @h3nry! Do you have a trick for laying out those asymetrical arches? 1 Quote
Popular Post h3nry Posted March 30, 2025 Author Popular Post Report Posted March 30, 2025 On 3/29/2025 at 10:04 PM, wtnhighlander said: Looking great, @h3nry! Do you have a trick for laying out those asymetrical arches? No. I'm just winging it. At the moment they look a little strange ... hopefully once the carved design is present the shape will look the way I'm hoping. 3 Quote
Popular Post h3nry Posted March 31, 2025 Author Popular Post Report Posted March 31, 2025 The router has done its job ... and I'm ready to get the gouges out again. 6 Quote
fcschoenthal Posted March 31, 2025 Report Posted March 31, 2025 Glad you showed the before and after routing the excess before finishing the carving. Really surprised at the difference it makes. I would probably take the shortcut of scrolling out the "fancy bits" and laminating them onto the panels. Routing out the waste really gives it a different look. Quote
pkinneb Posted March 31, 2025 Report Posted March 31, 2025 Looks awesome! So you do the routing freehand? Quote
Chestnut Posted March 31, 2025 Report Posted March 31, 2025 I'm more curious how you cut and cleaned up those odd curves so easily. Quote
h3nry Posted April 3, 2025 Author Report Posted April 3, 2025 On 3/31/2025 at 6:20 AM, pkinneb said: Looks awesome! So you do the routing freehand? Yes, all freehand. I try to stay just outside the lines, and then pare down to the line with the carving gouges. For a lot if the carving, the final edge will be slightly undercut to make it stand out more. On 3/31/2025 at 9:13 AM, Chestnut said: I'm more curious how you cut and cleaned up those odd curves so easily. Cut on the bandsaw, then cleaned up with a rasp and file before scraping and sanding. 1 1 Quote
Popular Post h3nry Posted April 3, 2025 Author Popular Post Report Posted April 3, 2025 I've got most of the carving done on the right hand door. It still needs a bit of cleaning up and sanding. 9 Quote
Jonathan McCully Posted April 3, 2025 Report Posted April 3, 2025 I've got most of the carving done on the right hand door. It still needs a bit of cleaning up and sanding. That’s absolutely beautiful. I’ve never heard of someone doing intricate carving like that freehand with a router. A previous picture looked like you had a small palm router in it. What kind of bit do you use for something like that?Sent from my iPhone using Tapatalk Quote
wtnhighlander Posted April 3, 2025 Report Posted April 3, 2025 @h3nry, do you create the carving designs from scratch, or adapt some sort of pattern? Quote
Popular Post h3nry Posted April 4, 2025 Author Popular Post Report Posted April 4, 2025 On 4/2/2025 at 6:35 PM, Jonathan McCully said: That’s absolutely beautiful. I’ve never heard of someone doing intricate carving like that freehand with a router. A previous picture looked like you had a small palm router in it. What kind of bit do you use for something like that? Sent from my iPhone using Tapatalk Just to make sure there's no misunderstanding ... the router is not doing any carving, it is simply renoving the waste where there is no carving to be done. The carving itself is done with gouges. I like to use a 3/16" bit which is small enough to get a lot of the detail, yet still removes material efficiently. 4 Quote
Popular Post h3nry Posted April 4, 2025 Author Popular Post Report Posted April 4, 2025 On 4/2/2025 at 7:40 PM, wtnhighlander said: @h3nry, do you create the carving designs from scratch, or adapt some sort of pattern? I don't have any designs. But I spend a lot of time on google lookin at images of furniture, and get inspiration from many pieces. Then try to combine the elements I like into one design. I'm not trying to challenge myself with the carving on this piece, so the design heavily borrows on the kind of thing I have done before ... the design of the leaves is very simple, and not sophisticated representations of acanthus leaves or anything else complex. 3 1 Quote
Popular Post h3nry Posted April 6, 2025 Author Popular Post Report Posted April 6, 2025 Finished the carving on the door fronts ... Unfortunately I'm going to have to pause for a couple of months here, as I'll be away. still to do: door panels, door shelves, top, finishing. 7 Quote
wtnhighlander Posted April 6, 2025 Report Posted April 6, 2025 I am still amazed at how quickly you work through those carvings! 1 Quote
Popular Post curlyoak Posted April 6, 2025 Popular Post Report Posted April 6, 2025 On 4/5/2025 at 9:27 PM, h3nry said: Unfortunately I'm going to have to pause for a couple of months here, as I'll be away. Me and I'm sure a bunch of others will be waiting for your return. Good luck on your travels. A pleasure to watch your projects unfold. Thank you. 4 Quote
Mark J Posted April 6, 2025 Report Posted April 6, 2025 What wtnhighlander and curlyoak said. 2 Quote
DanielJohn Posted April 25, 2025 Report Posted April 25, 2025 I made a flip-up section like that with a piano hinge and some felt pads underneath to level it out when closed. Held up great and stayed flush. 2 Quote
DanielJohn Posted April 29, 2025 Report Posted April 29, 2025 I ran into a similar cabinet dilemma a while back and ended up trying out ai furniture design to sketch up a model before cutting anything. It saved me from a bunch of mistakes, especially with tight tolerances for the drop-down sewing machine shelf. The cool part was being able to adjust clearances visually before committing to measurements. Made the whole process smoother. 1 Quote
Popular Post h3nry Posted August 19, 2025 Author Popular Post Report Posted August 19, 2025 I'm back after a summer trip sailing out to Haida Gwaii But to keep it woodwork related ... the Haida are famous for their woodwork. Most famous for their carvings on totem poles. After european contact when they acquired iron tools the relief on the carving became more pronounced ... this old pole with a much lower relief was probably carved in the old style using sharpened seashells for gouges. You can still see the mortice and tenon joints in the corner post of this old house. This house would have been built with iron tools, but the style is exactly the same as when they were using stone tools. This rafter still shows the groove that held the boards that made the walls. The boards would have been riven from logs using wedges, not sawn, and they would have been removed and taken with them when the village was abandoned. ... Right, now I have to get back to work on this cabinet. 7 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.