Finishing
2,922 topics in this forum
-
I recently turned a Purple Heart bowl and don't know how I should finish it. I want to keep the deep purple color I have right now but I also like what it looks like with no finish. So is there an option that will save the color but keep that close to the wood feel? Thanks in advance.
-
-
- 12 replies
- 5.2k views
- 1 follower
-
-
This is off the wall. But looking for a source for inlay moulding. I'm restoring an old chest of drawers and vanity. a good part of the moulding is gone. small stuff, 1/4 in wide and 1/8 in thick. Pics are a little fuzzy (ok, a lot) but you get the idea. My fingers are too fat to try to make myself. Thanks Mike Jones
-
- 5 replies
- 2.8k views
-
-
Highly leveraging the advice on this forum, i successfully applied my blotch control and dye (many thanks - debrief later when its all said and done). Yesterday, I applied my first ever coat of spray finish via the Earlux 5500 to the 6’x3’ table top. Enduro Var gloss. I now have orange peel after a complete dry. I have sanded this orange peel down a bit with 320 paper and wonder how far to go? In some spots, it seems i have gotten it completely smooth, but in most of the table, i have just sanded off the tops of the peel – i can see shinny low spots between each peak which didn’t get the sand paper. I know Enduro Var is very good at self leveling, but before I try a 2n…
-
-
- 5 replies
- 10k views
-
-
How can I remove green food coloring (dye?)from an oak cabinet?
-
-
- 4 replies
- 2.9k views
-
-
Hi all. Just discovered this website and I'm curious if anyone has found videos/articles on here related to a project we have for our company, Archer Seating. People love the oldtime look of ballpark seats, even if they're made from parts of unremarkable stadiums. One of our best sellers is this seat: We'd love to figure out a way to give it that old–time feel with our new seats. The wood is elm: Any ideas or previous projects someone could point out would be great.
-
-
- 31 replies
- 10.5k views
-
-
A beautiful walnut cabinet was given to us, for free, but it smells so badly of cigarette smoke I get the impression I should refinish it to seal in the smell and saving my nose/head from attack each time I walk by. I have never refinished anything and have a few questions: First information on the piece: 1. The piece is a china cabinet. Made of walnut with the backer board and bottom of the inside cabinet probably a cheaper wood. EDIT: I forgot to mention that I did a test with denatured alcohol which did not get tacky, so I do not think the original finish is a shellac. 1.5. This piece was in a smoker's household for at least 20 years. 2. Use: China ca…
-
-
- 8 replies
- 3.3k views
-
-
I'm refinishing an antique extension table that was my great-grandparents. At some point someone painted it a lovely shade of brown and yellow... I stripped the paint first with Citristrip, then used steel wool and mineral spirits to remove residue, then used a methylene chloride based stripper on stubborn sections, followed by another mineral spirits/steel wool rub down. This is the base after drying a bit and a light sanding with coarse grit sandpaper. Can anyone tell what kind of wood this is? The darker spots seems to lighten with sanding, but not significantly so. I was planning on staining it a darker/chocolatey brown but I don't want it to look splotchy. Wou…
-
- 4 replies
- 3.1k views
-
-
I am trying to mimic this finish from a pottery barn console table and can't seem to get it right! I've been using different combinations of GF's dye stain, but it appears to me that multiple stains are being used to build the color in layers rather than applying one. I almost wonder if it's stained and sealed, followed by several applications of different colored glaze. I'm not sure though.. Any ideas are greatly appreciated! I have more detailed pics if needed
-
- 6 replies
- 3.1k views
-
-
Kitchen cabinets have taken a beating, maybe should be replaced or resurfaced but plan on moving within a couple years so would rather not spend money on them. While learning woodworking, I now understand that lacquer finish can be prepared. How can I tell if finish is lacquer? Do you think I have a shot at doing a possible repair? Anyone know a good learning resource for this? Thanks!
-
-
- 5 replies
- 2.9k views
-
-
I used polyurethane to finish a red oak window sill in our bathroom several years ago when we remodeled. My wife spilled a silver dollar sized amount of nail polish remover on the sill (54"L x 8"D sill) and it ate through the 3 layers of poly (she forgot to go back & wipe the spill up). Is there any decent way to "mend" the poly finish without doing a full sand/strip of poly on the entire sill? I think I already know the answer. I am just hoping someone can point me in the direction of a decent repair process.
-
-
- 4 replies
- 3.2k views
-
-
I'm building new cabinet doors for the kitchen, also drawer fronts and the upper cabinets. I'm doing them in maple and using a general finishes oil stain, candle light. I've attached several pictures of spots that are showing up in the finish. I'm doing two coats of stain with 24 hours of dry time between coats. The spots were not there after the first coat but were after I attempted to wipe off the excess on the second coat. They disturbingly look like finger sized smudges. I'm wearing blue nitrile gloves as I wipe on and off the stain and it is possible I'm laying a finger on the board there but I'm not understanding why it isn't happening everywhere I touch and i…
-
-
- 6 replies
- 2.9k views
-
-
Hello All, I am new to this forum and in search of help deciding on a finish to use on the Cherry cabinets I am building. I have read through the posts on finishing and found that this subject comes up regularly. I have also noticed that there is a huge amount of experience and knowledge here. My experience in wood working in my opinion would be considered "beginner" but I have been around woodworkers my whole life and by taking my time and researching diligently before a new technique is used I do pretty well. The lot of Cherry that I bought is exceptionally colorful and full of beautifully contoured grain. While I have approx. 25% over the BF that I need, try as I mi…
-
- 18 replies
- 4k views
-
-
Hello everyone, I am trying to decide what finishes to use for a kitchen island, desk and counter top I am building. They are all made from reclaimed yellow pine bowling alley lanes. I framed them in pine trim to hide the abundance of nails on the long edges. The desk will likely be Arm-R-Seal but I want to keep the light pine look at much as possible, if you have worked with this, will it remain close to the bare wood look? My real dilemma lies with the counter top and island. I want them to be food safe, so mineral oil is an obvious choice but if I avoid directly cutting on them i think salad bowl finish will suffice and require less maintenance. What…
-
- 2 replies
- 2.8k views
-
-
What would be best finish for a hundred year old plus, piece of hemlock?
-
- 4 replies
- 2.8k views
-
-
I am refinishing a wood interior window again, I stained and am ready to protect, read that epifane would work well to protect the wood. I bought gloss for first coat but don't want it glossy. Can I top with some other satin product? If so any suggestions?
-
-
- 1 reply
- 2.6k views
-
-
My wife bought a nice sideboard last week which had a pretty beaten up top. (Her original plan was for me to make one but then she found this - imagine my disappointment.) Anyway... I bought some Restore-A-Finish and used that on it. It looked quite a bit better but even a couple days later, I was still wiping some color off the top with a clean rag. It says on the can that it should dry and be ready for wax in 30 minutes but after two days and repeated wipings, some color still is coming off. Not much but still I would expect none. Today I finally put wax on it which made it look a bit better still but I'm still wiping up traces of color. Any ideas othe…
-
- 4 replies
- 3.3k views
-
-
Greetings, I am a new member and have been reading numerous great posts on this forum for a couple months and need some advice so I thoughts would ask here. I drifted away from my tried and true finishing process of using BLO and then wipe on poly. I read good reviews about other wipe on products and decided to use Arm r Seal. I am at my wits end trying to fix streaks on one of the layers. I have a total of 7 layers and I thought that sanding and resetting the finish with another application would fix the problem...it has not. Anyone else have this problem and if so, how did you fix it? Thanks in advance Bruce
-
-
- 14 replies
- 14.5k views
-
-
I'm building a live edge maple coffee table (for indoor use). I'm not staining it, just keeping it natural. I decided to finish it with Helmsman Spar Urethane but with everything I've read it may not have been the best product to use. I'm at 5 coats and noticed that the in-between sanding with 220 grit is creating some tacky white looking areas that are not going away with the follow-on application. Should I scrap the spar finish and strip it back down to the wood and use another product or should I simply sand more aggressively a layer or 2 down and continue with the spar product? D
-
I am rebuilding a 1958 Alaskan truck camper that had a lot of water damage. I'm not trying to make it exactly original, I just want to retain some 1958 charm. The countertop is BS1088 ply that I hope to cover with vintage Formica when I find a piece to match the rest. Anyone have any suggestions of how I can get this to all jive together? Right now it is a mix match of several different grains and colors. Painting is a last resort, and I am no expert at finishes.
-
- 0 replies
- 2.9k views
-
-
Hi all, I'm a relative newbie when it comes to woodworking but I do enjoy taking on a project every now and then. My latest project is a outdoor bench made out of an old tailgate,red cedar for the frame and reclaimed barn wood for the seat and armrests and I have a few questions when it comes to finishing it. This will be an outdoor bench btw. 1) The cedar frame... I will be using red cedar from one of the local lumberyards, so nothing special there. Can I sand this wood smooth ie furniture smooth? What is the best method of achieving a smooth finish on this type of wood? 2) Reclaimed barn wood... I am unsure of the type of wood it is but I want to make sure that it i…
-
- 6 replies
- 8k views
-
-
When finishing a cutting board, Marc suggests using a 50% Salad Bowl Varnish with 50% mineral spirits... So therefore could I use denatured alcohol as my thinner?
-
- 2 replies
- 2.8k views
-
-
Hi! I am really new to finishing so forgive me if this is a stupid question -I just stripped and sanded some wood to refinish and the wood grain is all very dark in color, it looks unnatural, perhaps the effect of a previous stain. If it is unnatural, does anyone know how to get rid of it? If not (and if so) what kind of wood am I working with here? What might have caused this? [img src=http://s1287.photobucket.com/user/Schroeder846/media/Mobile%20Uploads/image_zps15511115.jpg.html] [img src=http://s1287.photobucket.com/user/Schroeder846/media/Mobile%20Uploads/image_zps0af1d5c4.jpg.html]
-
- 7 replies
- 2.8k views
-
-
Hello, We just had some trees cut in our backyard, one of which was a pine tree. The cutters chopped the trunk into manageable pieces and they are the perfect height for stools to put around our fire pit. What do we need to do to each stump to make it last? I did look through previous posts and saw that pine isn't really the best for outdoor use, but as these will just be extra seats we're not looking for them to last forever, just for a few years. They will be sitting on sand covered with gravel. We would like to leave the bark on. Thank you!
-
- 4 replies
- 2.8k views
-
-
Goog morning all, I am not sure in what section I should place this question, so I put it under finishing, since it is about painting wooden stairs. I have additional stairs going from the garage into the basement where my shop is. This is very convenient, all machines could go straight from the garage into the basement. Sometimes new machinery can go into the basement not passing the eyes of my wife, which reduces the amount of critical questions significantly. Anyhow, those are simple wooden stairs, nice in the beginning, now already pretty dirty. So I came up with the idea to paint them but I am somewhat concerned that paint will make them slippery. Well, my idea …
-
-
- 9 replies
- 3.3k views
-
-
I recently made a beer mug out of cherry and walnut. I would like it to be useable. I rubbed it with mineral oil but was told I would need an epoxy of some sort to make it liquid right and yet safe for the consumer to drink out of. Wondering what product I could use and possibly where to purchase it. Any suggestions are welcome. Thanks
-
- 13 replies
- 3.5k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·